Recently active
Mike,You were right that is has to be mapped to the syscol.scl file, but there are other steps that need to be included, such as turning off the gradient, then selecting the gradient and setting your own values. Here's a solution from PTC (see below image or click to enlarge):
PTC Community,In order to set the background color to white, the RGB values need to be 255 each. After selecting OK, the systems alerts the user if he/she wants to save this configuration. After saving this configuration to the config.pro file in the default load point, it won't keep the RGB settings. When launching a new session, the RGB values default back to 251 each. Does anyone know why the 255 values won't save?
Thanks for the response. This works, as shown below. I was making this more difficult than it should be, as I was trying to pattern on a curve, not dimension.
PTC Community,I'm trying to pattern some features on a curved component. To help facilitate visualization, I've included an image of the model, and the model itself. I would like to pattern the hole and the other features associated with the hole, extrusion, round (lower end of model tree), etc., along the blue curve. There was a recent discussion on a similar topic, as it was to pattern holes on a curved surface. I've tried to pattern features and to pattern as a group of features, nothing is "working" for me. Any suggestions and comments are welcomed. Thanks.
Hi Hector,If you want your sketcher to always be normal to your view, or 2d, you can set this up in your config.pro file with:sketcher_starts_in_2dBy default, Creo will use the iso view for sketching as shown in Figure 1. Set your config.pro file as shown in Figure 2, and your sketch will always orient to Figure 3. Some people like the default iso view, and if they want to switch to 2D, they just select the Sketch View icon.Figure 1: Default ViewFigure 2: Config.pro FileFigure 3: 2D View
Hi Vinay,If you're not concerned about the stresses in the threads, you could just apply a pressure distribution in the lower cavity using a 2D axisymmetric analysis while capping off the top of cylinder B.
Hi Mark,I know this "problem" has been put to rest, but I just wanted to show you that the Excluded Elements does really work, even on a single component. I took your model and created a Volume Region on one end of the beam. The excluded function excludes thoses elements from measure, not from the legend. I know, that's odd, but that's the way it works. You can see in Figures 3 and 4 below that the max prin is 1469 psi, not 1927 psi as shown in the legend. So when it comes to measures, the elements are ignored on the end of the beam.Figure 1: Volume Region on Beam EndFigure 2: Location of Max Prin in Beam (1927 psi)Figure 3: Max Prin the run Summary (1469 psi)Figure 4: Convergence on Max Prin (1469 psi)
After you download the libraries, you still have to install them? Correct?
I would recommend removing the material with a revolving cut. It's very simple. Just sketch the section you want to remove, and make sure you have an axis of rotation. You will only have to sketch half, since you can revolve the cut 360 degrees.
Hi Ryan,Create a surface feature with a curve through the points and make sure you have a closed loop. Extrude the surface to the desired length.Use the fill feature to fill in the ends of the blade.Merge the surfaces together.Solidify to make a solid part.Or you could just use the extrusion tool, sketch a spline through the points and extrude the blade as a solid.Can you upload the file?
Hi Naeem,Upload one of the parts that causes the application to crash, and I will see if I can replicate the problem.What Date Code are you using? For example, Creo Simulate 2.0 Date Code M080. Are you using a student version of Creo Simulate?What's installed on your PC in the way of, OS, Graphics Card and Memory, amount of RAM, etc.?
Hi Rohit,I'm not sure as to what you mean by "thickness analysis", but if you're referring to measuring the thickness of a uniform cross-section of a part, you just go to the analysis tab and select measures. You can measure the thickness by edge length or by distance with surface-to-surface. What version of Pro|Engineer are you using?
Laurens,I replicated your "problem", and I think the reason the displacement won't update is because you selected Legend Values in your template. This will lock in the max value. I ran two cases, as shown below. Figure 1 is using the settings you showed, and Figure 2 is running the model over again with 8000 N and I selected just Units for the template, and it updated the displacement fringe.Figure 1Figure 2
I selected the icon for User Defined Template as shown below, and I got three windows. The fourth is the one I added from my run. I didn't see any Displacement_Stress_test.rwt to select from as you showed previously from the above discussion. I'll just create one as you showed and run the model over again.
Hi Laurens,I looked at your model, and I plotted your template with the correct legend. I ran the model over again and plotted with no template, and then I compared it to your template values for displacement. I'm going to run your model again, and create a new template to see if I can replicate the error. Figure 1 is a run by itself. Figure 2 is your template with with my run added.Figure 1: Displacement with No TemplateFigure 2: Using the Template
This is a nice model, and I like the way you used the intersect function to give the wing an upward twist. I think what Jun wants is a continuous rounded leading edge until it tapers down to a rounded "point" (instead of having a flat end...see images below). This will require a bit more work to implement, and it's something I would like to see for myself. I don't know if this can be made with just a parallel sweep.
Also, can you upload your input file? This would be your model (.prt file ext).
I will need the solution directory that the results are based upon. In the mean time, I will run a small test model to see if I produce the "same" results.
Hi Laurens,Can you upload the file? I would like to take a look at it.
Try the below link:https://www.ptc.com/appserver/auth/it/esd/product.jsp?prodFamily=ENG
Hi Mark,The color of the on screen information such as "Structure: 3D Native Mode" or the default tolerances is defined by the System color for Secondary highlight. See the below images.
The 1st and 2nd planar walls were created off the same datum plane (FRONT), so no flipping is required. Yes, if you use the surface of the first planar wall, and it doesn't matter if it's the front surface or back surface, you will have to flip the the 2nd planar wall for proper alignment.
Daniel,In your attached model image, it appears that that first planar wall was flipped, which is opposite of the default direction. Once this is done, all planar walls created after this will have to be flipped. Figure 1 shows the default direction. If you keep the default direction, then the additional walls will look like Figure 2, and no flipping is necessary. It's not just creating a planar wall, but even an extrusion, as shown in Figure 3, the default direction will be towards the operator, providing the sketch is on the brown side of the datum plane. If the datum plane is rotated to the backside, the datum plane line will be black (these are default datum plane colors). Why Creo wants that default direction is beyond me, but you can avoid a lot of flipping by keeping the first planar wall in the default. I don't like it either, and I prefer to extrude features away from my view.Figure 1: Default DirectionFigure 2: Adding a Planar Wall in Default DirectionFigure 3: Default Direct
Hi Brian,In your model, it looks like the name A is being locked by Extrude 1. Deleting the Extrude 1 feature in the model will allow you access to the name A. You will also need to delete the gp0 and gp1 annotations. You will have to rebuild some of your model, but that will be easy since it's a simple model. It should only take you a few minutes. I was able to make a datum with the name A as shown below. This may not be what you wanted to hear, but this will fix it.
Hi Brian,If you can upload the model, I will take a look at it on Tuesday morning, and if you don't already have the problem resolved by then. I will be away from my office on Sunday and Monday is a Federal holiday for us. In the mean time, you could upload some images of your model with the entire model tree expanded (with nothing hidden or suppressed). If you're getting that message, then you have something already named "A" somewhere in your model.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.