Dedicated forum for our customers to share, collaborate, discuss best practices.
Recently active
Testing iframe
I am using Mathcad Prime Release 11.0 and Datecode11.0.1.0 Test case Please Ignore
I am currently running the trial version of Mathcad Prime 11.0.1.0 (I think only a few days left) to evaluate its capabilities for solving multiple equations with multiple unknowns. I want to verify that it will produce the results that I need before purchasing the software. I have run into a problem getting Mathcad to solve the system equations symbolically. I have looked around the internet for community information on this aspect of Mathcad but have not found anything that addresses my specific topic. The problem to which is seek a solution arises when modeling the impact between two bodies. Using the impulse-momentum formulation of Newton's 2nd law gives me 6 equations and six unknowns with a point mass (no rotational inertia) impacting a point mass. I put this system into Mathcad and used the solve feature and it produced the desired result. My file is attached. You will see that I took the solution equations Mathcad produced and ported them over to calculate the numeri
Mathcad Prime 10 A few years ago, I found this great Mathcad wrapper (GitHub - usnistgov/REFPROP-wrappers: Wrappers around NIST REFPROP for languages such as Python, MATLAB, etc.) for NIST REFPROP 10 where I can call properties using a script. This has been a game changer for me. The issue is that not all fluids that I need are available to me, (DMAc or MMA for example) in REFPROP.Does anyone know of a DIPPR/Diadem Mathcad wrapper out there that works well? Thanks
Hi, I have been trying to get this non-linear gear dynamics system of ODE's to solve but for the life of me cannot seem to correct the errors.The attached sheet has several attempts at the end to write the equations and initial conditions in different formats but all give "too few initial conditions" or a"floating point error". Like most programming errors its probably glaringly simple!Any assistance would be appreciated.Regards,Ross
Sir Isaac Newton This month’s challenge is inspired by one of the great unsolvable challenges of physics, the Three Body Problem. Of course, we won’t be asking you to perform the impossible in Mathcad Prime. Your challenge, should you choose to accept it, is the Two Body Problem for orbital mechanics. Earth-satellite two body problem Challenge 1: Create the math functions and programs that can calculate the position, velocity, and acceleration of a Mazda Miata-sized satellite in orbit around the earth. (Why a Mazda Miata? It was my first and only car. Feel free to substitute a car of your choice.) Choose your orbital parameters for altitude (e.g., medium-earth, geosynchronous, high-earth), inclination, eccentricity, and any other factors. Challenge 2 (optional): Incorporate advanced input controls to change the orbital parameters. Challenge 3: Graph the x-, y-, and z-values for acceleration versus time. Create additional graphs for velocity and positio
New to PTC community but long time user of mathcad. I need to get the Roarks formula's for stress and strain ebook but as best I can tell from the forums it is no longer provided with mathcad AND it's not available on the forums for download (or on the web as best I can tell). Is this correct? TIA
I want an algorithm that generates the function [a,b,c}=unique(Y) although there are forums what I need is for it to be only with structural control sequences if else for while etc but not advanced functions of either Matlab or from mathcad since when you want to replicate the function elsewhere it is complicated, it would be appreciated if you have a way to do it What would the mathcad programming of this algorithm be like as it is in the image so it is easier to carry out the function?
Hi there!I 'm trying to master the slider advanced control option to see how my goal function will be changed. On the PTC support page, I have found only the 2-axis plot sample:https://support.ptc.com/help/mathcad/r10.0/en/index.html#page/PTC_Mathcad_Help/example_slider.html#wwID0EIKIPB It looks like the upgraded version of Prime 10.0.0 probably has some bugs, or it is impossible to obtain such an option.I've attached the function sample (Prime 10.0.0), which I'd like to observe using the advanced control button (slider).Any advice or assistance will be appreciated.
We have a large number of installed users that use Mathcad 15 on a regular basis. Just recently, a few have been noticing that selecting File|Save from the main menu is NOT saving the updates to their files. You can imagine our concern. It's intermittent and I cannot reproduce it myself on my desktop, but I'm hearing it from enough of our users that I think it's real. It could very well be something to do with our environment and not be a Mathcad issue at all, but it is concerning. We're running Mathcad 15 M045 and one of the keys is that the attempted save it to a network drive, not a physical drive on the desktop machine. Has anyone by any chance run across anything similar?Thanks!
I'm wondering if anyone else is having this problem. Just noticed that Mathcad 15.0 M050, released specifically for Windows 10, has an odd printing issue. To PCL printers and PDF files, it appears that the font characters are all using a negative fixed character spacing on the order of -0.01 to -0.06. This "bunches" up the characters and pushes them all toward the left. I thought my eyes were going buggy because it is subtle, but when I print and examine a PDF, this negative character spacing is easy to analyze. Negative kerning is used for type-setting, but not uniformly on every character. It doesn't seem to matter which printer or which font or font size I use. I do not see this behavior with M045 on Windows 7. I don't know yet if it's a Mathcad issue or a Windows 10 issue (although all other apps print just fine). .NET maybe? I have a ticket open with PTC, but wondered if anyone else is seeing this, or has a clue as to wh
I normaly use odesolve in a solve block. However, I.m struggling to learn how to use the other ODE solvers with units. I asked AI to provide an example. Sadly, the AI example also failed. Typical (cryptic error messages: Mathcad Prime 11 file attached.
Attempting to use a range to help determine a solve block but am struggling to get this function to work. Any ideas on how to debug this issue? See attached image.
I am solving a system of 1D steady ODEs in Mathcad using RK4. The system works correctly until I add a heat transfer term representing two-way coupling between a gas phase and injected droplets. When this term is included, the solver no longer outputs results and reports that the gradient matrix must be scalar or a matrix.The gas stagnation temperature gradient depends on Reynolds number, Nusselt number and a convective heat transfer coefficient that is itself a function of the ODE variables, which vary along z (length of nozzle)All other gradients (Mach, pressure, velocity, etc.) are functions of the same state vector and work correctly when the heat term is removed. I suspect I am incorrectly defining a function within the gradient matrix or using If else wrong.Any help would be appreciated, as I'm going round in circles.below is screenshot of part of code: Thanks very much
GreetingsI have a rather strange question, with topic that some people might consider insignificant and unimportant, but this particular function that Im making will probably be used numerous times in a single worksheet. For that reason Im trying to optimize almost every function in my file as much as possible. Ofcourse I dont expect a detailed answer with testing results etc, but rather your thoughts on this topic.In this case, I need to determine in which region of IAPWS-IF97 (formulation for thermodynamic properties of water) the point lies on a pressure-temperature plot.P-T Diagram, Validity range of IF-97So, here is the question itself: wich model of (p,T) function would be faster and easier to calculate (e.g. on a low-spec hardware), the one with separated IF`s, or the one where IF`s combined with usage of multiple "and (˄)" and "or (˅)"?And will the result be different in Mathcad Prime?Model 1Model 2Functions and constants used (for clarification, in case you are interested)ps(T
I am using Mathcad Prime Release 10.0 and Datecode10.0.1.0Hello,is there a way to insert line breaks in Mathcad expressions, especially when using READEXCEL with long file paths? I need to read two matrices from different files and combine them using AUGMENT(A, B), but the full expressions do not fit on one worksheet line.Is line wrapping supported, or is there a recommended workaround?
Hi,I looked through the API guide and downloaded the examples. The last part of the code displays 'output1' in message box. It does not have example on how to show the matrixoutput1.Can you help with this? I need to get matrix from the sheet.
Hey there. I've been trying all sorts of different ways to try and get this solver to work. Different errors depending on the way I approach it. I believe it should solve. None working. all help would be amazing. Really the two outputs i care about are R_o and h_2.Thanks!
Hello Everyone.From : To : 1. How to plot a point in 3-D and : 2. Rotation of that point a angle t (say, = Pi/2) about X-axis ?Thanks in advance for your time and help.Regards.
Hi all, Currently experiencing an issue with an Excel component on a colleagues computer. The Mathcad file, attached, works on my computer fine but not my colleagues. States his "excel is busy". Any ideas why it works on my computer but not my colleagues? Many thanks,Iain FYI, I am using Mathcad Prime 10.0.0.0 (and is my colleague).
Hi thereI got this screen when I open Mathcad. what should I do to get rid of it ? my license is still valid to 2027 Regards,Yusra
I am using Mathcad Prime 11 and I am a bit confused about how symbolic solving and variable definition work. In my worksheet, I use the symbolic solve operator and Mathcad returns a value for VBL, but when I try to evaluate the variable afterward, it still appears undefined or does not behave as I expect. I am not sure whether I am using the wrong operator, whether the symbolic result is not actually being assigned to the variable, or whether I should be using a solve block instead. The following screenshot describes the issue. I would really appreciate any guidance on what I am doing wrong and how to properly define and reuse the solved variable in the worksheet.
Hi there ,I need to make CWD ,which is used to identify the location of the input, fixed . So if I send my Mathcad sheet to someone else he can open the sheet and see the calculation.Is that possible or he has to change the CWD and the input file ( in_file) ?Regards, Yusra
When using the symbolic solver, Mathcad Prime 11 often puts in unnecessary parentheses. I've tried every keyword in the symbolics pull-down menu to get rid of the parentheses with no luck. Is there a way to get Mathcad to remove the unnecessary parentheses? For example, I would like to see the following.
I’ve been looking at automating some calculations with the Viktor program. Viktor acts as a kind of app builder for python apps. I’d like to use MathCAD to perform the actual math for the calculation because it’s easy to see the math workflow, but I’d use Viktor as the bridge between my finite element program to bring results into MathCAD and to help visualize results. Does anyone have any experience with integrating MathCAD with Viktor? Any guides or tips you can provide?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.