Recently active
Do you want each arm to wrap around a sphere, or do you want the entire extrusion to wrap around a sphere?
Did you check the run summary file?
Do you have a picture or sketch?
Are you talking about the Mechanism function as shown below? This only appears for assemblies, and not single components. I don't know why anyone would want to disable it. What is your rationale for wanting to remove this?
That all depends on the region and data of interests. 1. Do you have a picture or image of the bolted assembly?2. How is the assembly loaded?3. What are the boundary conditions?4. Where do you want to recover the stress?5. Do you want a multi-body contact analysis where the bolts are solids?List the requirements for your FEA study.
Can you upload an image of your problem? Better yet, can you upload the model? What scale did you make your plot? Is it a multi-body contact analysis?
If you move the cursor over an icon, for example, Hole, and press F1, it will open the Help Center on how to make holes, as shown below (if Help Center is installed):
You have a zip file within a zip file. Please save over again and upload. I cannot check your run summary for positive separation stress values. If you have positive separation stress values, read the following note: A positive value for the separation stress measure indicates that the distributed separation spring has the undesired consequence of forcing the two contacting areas to remain in contact with each other, even though they should naturally separate. To fix this issue clear the Fix Separation check box and create a contact interface between the two parts that are connected by the fastener.
The diagnostics for AutoGEM should tell you where the problems are located and will even make invalid elements red. You may shrink the elements as shown in the below example (this one is 30%). I don't know of a way to show the mesh transparent before processing, only after processing.Figure 1: Brick Elements on a PipeFigure 2: Brick Elements Shrunk 30%
Attached is the latest IDD from PTC.
When you open each image, there's animation. Are you asking can Creo perform the animation? Or can Creo make the parts by relations with equations? Or both?
Figure 1 is the "watertight" joined surfaces, which cannot define a closed volume.Figure 2 is a solid, which can be defined.Figure 3 is the "watertight" joined surface, which material cannot be removed.Is this what you're talking about?Figure 1Figure 2Figure 3
Shaun beat me to the question...I was going to ask for some images too. Can you provide us with some images?
Hi Scott,What are you attempting to analyze with a fastener through three components? Are you interested in just the fastener loads? Do you want stress results in the components?
Just to illustrate what Michael is referring too, look at the below image. The preselection highlighting is checked, and don't forget to check the filter. In Creo 2.0, it's in the lower right-hand corner of the GUI. Make sure the filter is selected for something that can be highlighted. Setting it to Smart will allow highlighting of anything. Notice how I have one component in the assembly highlighted. Welcome to the forum.
Here's how you can change that. If you want N for Newtons in your measure definition, change your model properties. Go to:File>Prepare>Model Properties>UnitsSelect and Set to (MKS) or (mmNs) as show below. I think you must have selected (mmKs), and this will give you the mmkg/sec^2 for Force in the Measure Definition. You can include Subcomponents under the Info tab.
It sounds like you have already figured out this particular problem in the model. If you're working with SI units, then of course, your force should be in Newtons, as shown below. I don't work with SI, but I quickly converted my units to MKS, and I got the right units for Force in the Measure Definition window.
Guilherme,It appears that you have some Measures that were defined and they are called:placaII_axialplacaI_axialand I don't know what units were selected for the Measures.
Hi Tomas,You can hide all of the annotations or part of them using the Show Annotations tool. In the below example, I have all of the notes unhidden, but I can hide all of them with the encircled icon, or I can go down the list and select whatever ones I desire. Notice the six tabs below the Show Annotations text. You have to select the right type of annotation before you can hide/unhide.
Hi Guilherme, One thing I might add to this discussion is the use of preloaded fasteners due to wrench torque. I’ve attached a document to illustrate how to use the preload. It’s for WF4, but it will work in Creo 2.0. This is one area that’s overlooked, and there’s not much documentation out there to tell you how to use preloads. I highly recommend reading and working the example in the attached document so you may become familiar on how to obtain the right preload for fasteners. You have to make two runs in Simulate in order to accomplish this, yes, even with Creo 2.0. I think this will change for Creo 3.0. I’ve attached another document that explains infinite friction, along with other Mechanica contact theory, and this is really used to indicate slippage. It’s called “friction” in WF4, but when you enable infinite friction, the elements actually bond together. This is still the same for Creo 2.0. I have always turned the Fix Separation off and placed contacts between bodies. When yo
Guilherme,You can't pattern fasteners, but you can copy and paste a fastener along with all of its assigned properties, then just rename the fastener after pasting.
How about uploading the file or some images?
I didn't have any problems adding a Surface Region at the assembly level. True, it places the surface at the component level, but you can add it in the assembly. I just added a Surface Region to the assembly below and put a load on it.
Hi Eric,Try this first:File>Options>Entity Display>Show Datum Plane Tagsas shown in Figure 1 below.Figure 1After you open the model, make sure the Plane Display icon is selected, as shown in Figure 2 below.Figure 2If this does not work, then implement the method shown by Praveen. Welcome to the forum.
Mark,You stated concerning contact:For multi-body contact with mis-matched surfaces, Split Surface can be enabled (shown below) to split the surfaces in the region of interest. I think this discussion is about Creo's fastener tool, which does not create a solid fastener. I've used the surface region creation technique for solid bolts, with solid heads and nuts. But you could still split the surfaces with the interface tool. PTC developed the Split Surface function in the interface tool to save time in creating matching surface regions.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.