Recently active
I would submit these under Product Ideas for voting, and the developers will also see your ideas. The developers won't see it under discussion/question.
Every time I try to open up one of the student versions of Creo Parametric in a professional version, I get the warning message that I cannot open it because it was created in a student version. This happens when I attempt to help with some of the problems in the community. Has anyone else experienced this?
kaci_54459,Were you able to create the desired geometry based upon the furnished information?
Thanks Dale.
Try uploading the file and a sketch of what you want. This will help us with your definition.
Mike,I've attached PTC's instructions on how to use the Import Data Doctor (IDD), a 54 page pdf file.
Hi Seth,I can see any images.
After you import the .stp file, it will convert to a .prt file after you save it, without modeling history.
Here's and example of using Published Geometry in the below YouTube video:http://www.youtube.com/watch?v=dW7csIeh7c0
What version of what software are you using?
Hi Sam,I think this is what you're looking for. Here is an example that I made of a nonlinear sweeping coil wrapped around a linear sweeping coil. Look at the images below and see if this is the concept. The fact is, Creo can make a nonlinear coil around a linear coil.
Hi Shobhit,You may want to try setting your decimal places using the config option:param_dec_placesYou can set the number of decimal places from 0 - 14, as shown below. Try setting it to 3 and see if this works for you.
You can isolate areas of the bar with Simulation Features, assuming you're using Creo Simulate. Can you upload an image of your problem?
Hi Ryan,If what I provided to you is correct, could you go ahead and mark this discussion as correct, as this will help others who are searching for solutions. Thanks.
Frank,What do you mean by Creo does not have solid body sweeps? Or do mean making a sweeping cut with a solid body?
David,If you enter x, it comes back with an invalid relation.
Hi Sam,Here's an example on how to make the coil using an equation. You can use the same curve in Figure 4 to make the nonlinear coil to wrap around the linear coil, as shown in the nonlinear method video.Figure 1: Curve from Equation MenuThe following relations were used to make four turns of the coil with a radius of 1.5.Figure 2: RelationsFigure 3: Helical CurveFigure 4: Created Helical CurveFigure 5: Helical Sweep
Hi Mike,After importing the STEP file, are the surfaces purple? If they are, then you have surfaces and not a solid. By default, Creo shows surfaces in purple and solids in grey.If you have just surfaces, can you merge them together and then solidify?Sometimes when people export geometry as a STEP, they don't save it as a solid, but only as a surface.Can you upload the STEP file?
Hi Sam,What you're asking can be done, but I don't know if making the first helical sweep (the one attached in your question) should be with Creo's out-of-the-box helical function. What you will need to make another coil around the existing coil is to first have a trajpar that will follow the center of the first coil. Imagine a blue curve following the center of the first coil. This can be made with a curve through points, as you will have to establish the points. Once you have the first curve and a helical sweep made from that curve, you can then make a nonlinear helical sweep around your first coil. The nonlinear method is demonstrated in the attached video:http://www.youtube.com/watch?v=jXYoUdE6eSgThis other video is attached for general knowledge of helical sweeps. This video shows how to bend a helical sweep with a curve, but it shows it only in one plane. This example is towards the end of the video.http://www.youtube.com/watch?v=V4R8kQh3bos
How do you add the syscol.scl file to the config.pro file?
Hi Troy,You can turn this off (and back on) with the config option prehighlight. This option will turn off everything from being highlighted. You can add this option to your configuration file as shown below.
If this answered your question about turning off lines, could you mark it as correct. Marking a question as "correct" will help others when searching for solutions. Thanks.
Can you upload a picture of the component?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.