Recently active
Hi Matthew,First, did you import the STEP as an assembly as shown below?I imported the STEP as an assembly, and it lists all the components in the model tree as shown below.
I don't think you can, as I had contacted PTC support on this "problem". Besides, why would you want to do this? Unless you received an assembly from someone else, and you're concerned that the assembly may have mixed units? I would like to see Units added to the Model Tree Columns, but currently, it's not listed. You have to set the units under the Units Manger, but you probably already know this. But this won't show it under the model tree.
Here's how to turn on your Datum Planes in the model tree (and keep them turned on):Select Tree Filters:Select Datum Planes and anything else you want:After you make the selections, you will want to save them:Save your model tree configuration file, and then you will have to map to it under Options using mdl_tree_cfg_file:
Here's a model that is closed and not ground. Look at the two images below, and see if this is what you're looking for. Also, I attached the model, and you can review the model tree to see how I made it.
Probably like: Closed not ground, as shown below.
Look at the attached file. The spring was created using a helical coil by equation, based upon the information you furnished. Take a look at this and see if this will help you get started in the right direction. In the attached file, I used:r = 5.4theta = 9.5*t*360z = 10*tfor the equations.
Technically, Creo could do the same thing. You could create a datum plane through the part or assembly, remove by extrusion or "slice" as you call it, the features to hide, then sketch the desired features from the datum plane. Then you would remove the extrustion or "slice" without interferring with the features that was just created inside the component or assembly.
Can you upload the file? I will take a look at it.
First of all, I wouldn't use a cut surface as a reference, and that's what you're asking Creo to do. It's a better practice to model off real datum planes. You want to be able to "slice" the model while in sketcher and use the surface that was created from the "slice". Right? And then you will "unslice" the model in sketcher to continuing with modeling? Inventor/Solidworks must have some built in function where you sketch on this "sliced" plane and it's reference to a plane and not the actual part surface, I assume this. What happens if you try to modify the part later and you find out that you can't modify it because a dimension is referenced to this "sliced" plane? I haven't seen this in Creo, but it sounds like a nice feature to have, as long as it acts independent.
Solidworks has both the h and p method for FEA. There is a great YouTube on it, and if you would like to see it, I can include it in this discussion. I use Creo Simulate, because we have Creo Parametric.
You can measure the area of a 2D drawing if you import a 3D model, as shown in Figure 1 below. If you make just a sketch in 2D, as shown in Figure 2, you cannot measure the area. So while in 2D sketch, you can and cannot measure areas, just depending on how you use it.Figure 1Figure 2
Antonius,The 2D area has been filled, but you cannot measure the area. Notice that the Measure function is deactivated (grayed-out). This was created in 2D, not importing a 3D. Sure, if you import a 3D, then you can measure the area. But if you create it in 2D, you cannot measure the area...or can you?
Read Only doesn't really lock the features in the model tree. If you make the features "read only", then any user can remove the read-only setting by selecting the Clean function as shown in the below images.
AutoCAD will perform the function you're looking for. If you have AutoCAD in house, I would recommend using it.
Do you want the extrusion that represents the man-hole to be a seperate component? Or do you want the tank to be made as one component? Either way, this can be performed. The below images are of one component, but I could have made it an assembly. But I think this is how you want the features to come together.Figure 1Figure 2Or do you want it to penetrate like Figure 3?Figure 3
Here's a link to FloEFD, as you can use FloEFD with Creo, CATIA, or NX:http://www.mentor.com/products/mechanical/products/floefd/Also, I attached the FloEFD brochure for your viewing.FYI.
Could you please elaborate on your phrase "everything is Linux based". I'm assuming that the OS for CFD is Linux, and the OS for CAD is something else. Or do you want Linux for both?
If you prefer Creo, you could try FloFED for Creo with a free trial version.FloEFD for Creo is a fluid flow and heat transfer analysis software that is fully embedded in Creo Parametric and Wildfire and is based on proven computational fluid dynamics (CFD) technology. Unlike other CFD software, FloEFD for Creo works directly with native Creo Parametric and Wildfire geometry in order to keep pace with on-going design changes. Because you are using the same geometry for CAD and analysis, FloEFD for Creo allows you to maintain a single set of data across your project design process.
If you're looking for computational fluid dynamics (CFD), Creo does not offer this capability with their analysis and simulation software. We have CATIA, NX, Creo, SolidEdge, Solidworks, StressCheck, and ANSYS. Can you believe that? Yes, here at MCAS Cherry Point, NC, we have that many versions. NX (everthing of NX) was given to us for a 18 month trial period, and our organization just spent over $1M for CATIA. I've been learning NX for the past couple of weeks, and what I don't like about it, is that it uses boolean operations to remove material, I mean, how out-dated is that (not that there is really anything wrong with it).So what you're looking for is modeling and then CFD on those models. NX and CATIA both have CFD, and it is probably fully intergrated with the CAD side of the house. Compare the cost of 4 licenses between the two companies, CATIA and NX, with only the modules you need. Either one would meet your needs.
Mark,You can set the number of decimal places in your sketch as shown below. You can also add the option rounded_display_dim_values and set it to yes/no.
Equipment for measuring resistance by Bert Witsmeer.Happy March, everyone! In case you missed it, be sure to check out the winning entries for our latest PTC Creo design contest.Here is this week's Member Showcase Roundup, demonstrating our members' expert use with designs, 3D models, worksheets and how-to's:Solid "Deep Drawing" (how to?)By Davide BoniMathcad to calculate magnetizationBy Denis GorbunovParticipate in the 25th Anniversary trivia contest and win Red Sox ticketsBy Monica Simon (gallery)By Vipul SandhirMacro for Creo Simulate Fastener ResultsBy Steven DunkerCreo Parametric animation: Red BalloonsBy Vladimir PalffyHow to minimize the waste on a DVD?By Walter SchrabmairScreen Captures w/ Background ImageBy Antonius DirriwachterFIND command with limited variable rangeBy Max GomesFeel free to click on any of the links above to discuss, like, rate or reply to any of this weeks' posts. Congratulations to our highlighted members for their incredible contributions this week.Have yo
PTC Community,There appears to be a discrepancy with the following warning message:You cannot select Calculate Large Deformations even though the run summary states it. The check box is greyed out.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.