Recently active
If the parts in creo are purple, then you only have surfaces and not solids. You can convert these to solids by merging the surfaces together then solidify. Once it solidifies, it will be gray in color. Then you can export it as a solid.One place it sounds like you have a solid, and another place it sounds like you have surfaces.
Hi Giulio,Just what exactly are you trying to analyze in the assembly? Is there a specific component that you're trying to analyze or several components? Are you looking for displacements, stress, etc.?
Hi Giulio,1. Your model would not mesh in Creo Simulate 2.0 (code M080) as shown below. I'm not saying it would not mesh in earlier versions. 2. When running fasteners with a preload, you will have to make two runs in order to get the right fastener load. If you want some information on this, I can furnish it.
Here's another example of pre-loaded fasteners using two runs.
The attached document shows why you need two runs for fasteners.
Under the configuration options, add "enable_absolute_accuracy" and set to "yes". Then change it to maybe 0.006 to start. You could make 0.0001. Just try different settings until it works.
Giulio,I took a brief look at your assembly, and here's what I'm seeing that needs attention:1. The model won't mesh because of invalid fasteners. You have fasteners going through holes of different sizes. The bores need to be the same size.2. Some of the fasteners are connecting more than two components. Creo's advanced fastener is only for two components.3. This is a multi-body contact problem, but there are no contacts. If you leave Fix Seperation off in the fastener definition window, the components will bind around the edges of the holes. To avoid this, you will need a contact interface. If it doesn't matter, then leave as is, if you're not interested in fastener loads.4. The geometry appears to be symmetrical. If the loads are symmetrical and parallel to the plane of symmetry, you could cut this assembly in half.5. The Exclude Elements needs to be selected before running.
If you isolate a component, it will ONLY exclude it from measure in the run summary file and not the legend level. And you must remember to check the exclude elements in the run study window. The image you're showing is only the AutoGEM setting. Also, if you're running a multi-body contact analysis, you may want to keep it, depending if it's in contact with another member of primary interest. Do you have an image that can be uploaded?
valentine contestThanks for the prizes Ryan, they arrived today and everyone at work is jealousheres to the next competitionJeremy
Lawrence, I took a look at your image, and it appears that you could apply symmetry, using just 1/8 of the model (if it's not symmetrical, then this won't work). You have identified simulation with shells. Could you not use volume regions for the copper fills and assign the appropriate material properties and run the model as a solid? The below images is not your model, but the concept works when applying symmetry to three sides. You will not get singularities, because the three sides that have symmetry are not locked, but they slide along the plane of symmetry. The 1/8 aluminum cube has a 500 degree F thermal load, and you can see the global magnitude displacement for the model, as shown below. You could plot the displacement in X, Y, Z alone. For example, the Y displacement is shown below. So the total displacement in Y would be double of what you see 2(0.032") = 0.064".If your model is not proprietary, could you upload it? This is an interesting problem to work on.Figure 1: Symmetry
Can you upload his model?
When you want to add a surface region at the assembly level, you click on the component you want to add the surface, and what this does is activate that component and turn all other components transparent gray. It's just like when you activate a part in the assembly while in Creo Parametric, all other parts are transparent gray. If you're not getting to this stage, then something is clearly wrong.
Just exactly what are you trying to attempt? Are you trying have mating surface regions in the assembly? Are you attempting a multi-body contact analysis?
If you want to assign your own mass properties in Creo:File>Prepare>Model Properties>Mass Properties>Changeand you will get the following GUI:
If the model was imported as surfaces, the surfaces need to be merged, then solidify the part. The part will then be a solid. Add a csys, if it doesn't already have one. Now, check the mass properties by selecting the csys. If you know the material type, you can assign it then check the mass properties. Right now, the reason the mass is incorrect is because the model has no mass, it's just imported surfaces.
Unique workstation design created by BJ PHere is this week's Member Showcase Roundup, demonstrating our members' expert use with designs, 3D models, worksheets and how-to's:Revolve ToolBy Wes HODE Solve Blocks with conditional statements used to switch equationsBy Mark BucktonModeling a Hacksaw Blade (Creo Parametric 2.0)By Nisheeth SrivastavaMathcad Memory Leak - Large Data on ClipboardBy Kenny LemensDid You Know? Creating a Square to Round Blend in PTC Creo ParametricBy Thomas McKeownCalling REFPROP From a Mathcad 3.0 Worksheet (via Excel Component)By Matthew StricklandWho should attend our Master Class at PTC Live Global?By Bettina GiemsaPunch form, exclude surfacesBy Stefan LomanOpening .igs or .stp files in CREO with the geometry in the tree.By Matthew CarpenterFeel free to click on any of the links above to discuss, like, rate or reply to any of this weeks' posts. Congratulations to our highlighted members for their incredible contributions this week.Have you had a chance to demo
You could use the curve created with the style tool to revolve a feature, such as a surface, but you will have to use pick edge on the curve created with the style tool while in sketcher mode. You will also need an axis of rotation. The curve created with the style tool is just another curve.
Does anyone know where and how to set lead_trail_zeros in Creo?
Hi Naathan,The .mfg file is obsolete. All manufacturing information will be stored in the .asm file. You can read a legacy .mfg file in Creo Elements/Pro, however, the file is converted to .asm when saving.Product InformationProductPTC Creo ParametricProduct / ModulePTC Creo Complete Machining ExtensionPTC Creo Complete Mold Design ExtensionPTC Creo Computer-Aided Verification ExtensionPTC Creo Expert Moldbase ExtensionPTC Creo NC Sheetmetal ExtensionPTC Creo Prismatic and Multi-surface Milling ExtensionPTC Creo Production Machining ExtensionPTC Creo Progressive Die ExtensionPTC Creo Tool Design ExtensionVersionWildfire 5.0Product Functional AreaManufacturing (NC, Expert Machinist)Mold Design & CastingUser Interface Location Processes, Initiatives, and Best PracticesManufacturing Process ManagementTooling Design & ManufactureBenefits and DescriptionThe .mfg file is removed and all the information for the manufacturing model is stored in the .asm file. This simplifies data manag
Could you upload an image of what you're suggesting?
If you're going to turn fix seperation off and if you're interested in the tensile force of the bolt, then you will need to have a contact interface between the components. When you enable fix seperation, the components actually bind around the edge of the hole, as I explained this in my attached pdf.
I'm reading "run" and "re-run" in your dialog, and it sounds like two runs? I was under the impression that Creo 3.0 will use only one run. Actually, I have a briefing on it titled, "What's New in Creo Simulate".
You still have to make two runs in order to get the desired pre-load, even in Creo 2.0. Creo 3.0 is supposed to eliminate the extra run. The attached pdf model is in Creo 2.0. The first image in Mr. Simpson's discussion shows two components, upper and lower plates.
The votes have been cast, collected, and counted. Now it's finally time to announce the finalists for Our 2014 PTC Creo Valentine's Day Design Contest! Here are the top three four community winners (we had a tie!) as voted by you, the members of our PTC Community:"Heart Family Vase" Uploaded by: Sven Wiebus"Valentines Day Teddy Bear" Uploaded by: Yogesh Yadav"Twisted Heart Vase" Uploaded by: Jeremy Connaughton"Gyroscopic Heart Locket" Uploaded by: Jehan KothariCongrats to all our winners and a BIG thank you to everyone who participated in Our 2014 PTC Creo Valentine's Day Design Contest! As promised, we'll be sending out some really great PTC Community prize packs to all of our top vote getters. Be sure to head over to the to check out all of this year's submissions and stay tuned for more fun challenges and design contests on our blog coming soon.
Charles,In order to get the right pre-load in Creo Simulate, you have to make two runs. The attached pdf file will explain how to do it.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.