Recently active
Hi Denis,This is "similar" to the way Autodesk Inventor does it. They have a tool where you just select the surfaces and fill in the void, but they still have to compare the two volumes.
Hi Denis,What do you mean by "internal volume of a shape"? Could you upload the "shape" or component in the discussion?
Hi Denis,Here's a simple way to calculate the internal volume:With the part in session, measure the volume of the part as shown in Figure 1 below:Figure 1: Volume = 420.312 in^3Now, suppress the internal volume and measure the new volume as shown in Figure 2 below:Figure 2: Volume = 500 in^3Find the difference between the two volumesInternal Volume = (500 - 420.312)in^3 = 79.688 in^3If you did not create the part and received it as netrual file, you could fill the internal volume with an extrusion. This is as about as direct as you can get.
I don't know of a "direct" method, but the below video will show you how to do it.http://www.youtube.com/watch?v=dW7csIeh7c0But there are other ways to do this, as this is just one method.
Can you upload the tube (input file) with the desired background color?
Hi Mark,Let me see if I can understand your concerns.In your attached image, you are pointing to two seperate things, and you're actually in Creo Simulate 2.0, not Creo Parametric 2.0. Correct?1) You want to know if you can change the color of the default WCS icon (green) to some other desired color? Your arrow is pointing to two csys, one for Simulate (green) and one for the part (black).2) You want to know if you can change the color of the default structural mode text (grey) that appears in the lower left hand corner?
Export to .dwg.
Can you upload an image from Autocad showing the example of what you want Pro|Engineer to accomplish?
Hi Steven,Perhaps you could upload some images of what you're attempting to accomplish. Creo drawings are 2D drawings, and they can also be considered 2D design drawings.
You can create any type of tube with the Sweep function as shown below:
Mark,In response to your questions, I got Simulate to ignore the stress at the constrained end by creating an assembly, where one section of the beam is 199.5" and the other is 0.5". These two components mesh together in the bonded mode, and the beam acts as one body. Then I just plotted the 199.5 section, and that's how I was able to show Model Max without annotation.
The below snippet has a max prin of 1470 psi with convergence on the solution. I think you said it was approximately 1500 psi?
Mark,Did you remember to select Exclude Elements in the Exclude Elements tab before running the analysis? I looked at your input file, and this was not selected (the .zip file that was uploaded). If you're not concerned about what happens in that end of the beam, you could exlude the entire end with a volume region, etc.
Your model generates 9096 elements because of the AutoGEM setting control where the max element size was set to equal to 2.Figure 1: AutoGEM Settings Max Element Size = 2The default settings generate only 780 elements.Figure 2: Default SettingsTry running your model with the default settings and compare the stress in the region of interest and see if it isn't about the same.Creo Simulate is based on the p-version of the finite element method, in which the fidelity of the finite element model is increased by raising the polynomial orders of the finite element basis functions. This approach is in contrast to traditional h-version finite element programs, in which the fidelity of the model is increased by adding more elements.
Hi Mark,In your problem statement, does it clarify how the beam is supported? For example, is the LH of the beam pin supported in XYZ and the RH with a roller support but constrainted in Y? This appears to be how your beam is constrained.Figure 1: Shear Moment DiagramsFigure 2: Constraint on LH of BeamFigure 3: Constraint Near RH of BeamOne thing I noticed about your mesh, it has too many elements for the p-method. Suppress or delete the AutoGEM for element size, because this will generate over 9000 elements.
Create a tube with any desired bend using the Sweep function. If your tube is contained in only one plane, then create the datum plane. Next, create a datum curve with the desired bend, as this will be the trajectory. Now create a sweep that will follow the trajectory.The datum curve can be modified, length, angle, etc., if the tube needs to be edited.If the tube requires more than one plane, create them as needed and create the trajectory.
Hi Mark,I think the best way to replicate your attached sketch in Creo Simulate is to use the Beam Tool function to calcuate the reactions loads, shear and moment diagrams.The below link will show you how to use the beam tool, even though it's for a truss problem:http://learningexchange.ptc.com/tutorial/788/creating-a-structural-truss-analysisThe below link is to a preview of Randy Shih's book, and look at the images that show you how to perform a basic beam analysis (pages 6-3 thru 6-46):http://books.google.com/books?id=OmcBhw_R85kC&pg=SA6-PA15&lpg=SA6-PA15&dq=creo+simulate+beam+tool&source=bl&ots=k0Ms9hHRxk&sig=UuZfT7GhkuhEGgJKVr08JkqDmO8&hl=en&sa=X&ei=W6DIUqK3PMil2wXYlIGIDQ&ved=0CFUQ6AEwBA#v=onepage&q=creo%20simulate%20beam%20tool&f=falseBased upon your exegesis, you have created a 3D solid model for your problem. I can take a look at your model next Tuesday, when I get back to my office. But try looking at replicating your problem wit
1. Right mouse click on the icon to make sure it's pointing to the .exe for Direct Modeling Express2. If the path is correct to the .exe, uninstall and reinstall Direct Modeling Express.I used the 32-bit app last year with no discrepancies.
Hi Rayudu,Yes. It is possible to calculate. Go to the Analysis tab and select the Mass Properties function. Select the desired csys and apply. This will generate a report with the cg of your model.
With the Dell M4800 (15.6 " platform) you can get a screen resolution of 3200 x 1800, QHD+, which is better than a retina display from Apple, and still within your budget. I don't think the QHD+ is available with the M6800.
Try looking at the Dell Precision Mobile Workstations, M4800 and M6800.http://www.youtube.com/watch?v=Jl65c-J0MgA
Hi Giuseppe,First, upload an image of your intersecting holes, and point out the subject intersecting curves that require geometry creation.You have two intersecting holes that are normal to each other with different diameters. I assume that you made the chamfer on the smaller bore, that intersects the larger bore, and now you want to put a round feature on top of the chamfer?
.
What do you mean by "lock"?
Hi Adnan,1. Pro-e files are forward compatible, so you should be able to open a Pro-e (.prt file) in Creo 2.0.2. You can open Solidworks file after you download the free Solidworks Explorer from Solidworks. The link to the YouTube video shows how to do this:http://www.youtube.com/watch?v=H537w3jnCp4
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.