Recently active
If you just want to send 3D files that don't include modeling history, you could save the files as Creo View files (.ed, .edz, .pvs,.pvz), and they can view with Creo View Express, which is free viewer from PTC.
It is recommended to add Units for the model tree columns. When dealing with assemblies, the end user will be able to see if all the units are the same at-a-glance. This will be very beneficial when obtaining assemblies from other users, as sometimes not all components in the model tree will have the same units. Currently, Creo does not have this capability (PTC Case #11906045).
There are many lessons in the attach link.http://learningexchange.ptc.com/tutorials/listing/product_version_id:44
Are you refering to the method in the attach video?http://learningexchange.ptc.com/tutorial/456/using-the-draft-analysis-option
Nice work.
Damian,Glad it worked out for you. I've been so busy, I haven't had time to dig into the problem. If beams didn't work for you, I was going to mention using shell elements instead of solid elements, if you wanted to keep the fasteners in the joints (if fastener analysis was a requirement).
Justin,Are you wanting to send a 3D model that can only be viewed without any of the features that was used to create the model?
Damian,This is an extremely large model for FEA. Do you think you'll have the RAM and disk space to run this? Yes, I downloaded it.
I'll be out of the office tomorrow.
Damian,When you zip the assembly, you have to include all the subcomponents. It may be better to build this with the beam element tool, if you're only trying to get the weight rating for the structure.
Hi Damian,The first thing I noticed is this is a huge model in terms of p-elements. You've got more than 197K elements, and more than 66K nodes. You have a load on a curve that is not associated with any elements, as this can be seen in the original post. If your model is not proprietary or classified, upload it, and I'll take a look at it. There just seems to be too many elements, too many problems with this assembly. What kind of results do you want out of the analysis? And are you running a Student version of Creo?
Whenever you're dealing with a lot of components for FEA (especially contact), start with a small assembly for meshing, then keep adding to the assembly. I would recommend going back to Parametric and suppressing all but the two components that won't mesh. You want all of the geometry to mesh before you start adding a lot of simulation, so you can suppress all the simulation features in Simulate and then resume them later. But first, get the geometry to mesh.
Damian,Go to the Diagnostics window and select File > Save As and save the file. Can you then upload the entire diagnostics file for us to look at? There's something wrong with the geometry, and if you will select on the identified errors, it should tell you the problem.
I don't think there is an config option for this, but I like the clean look of not having plane intersections, as they would just get in my way. However, you could submit this as a Product Idea.
Nathan,Move the cursor over small white square (circled in red) until it turns black. Now RMB and select "trim at". Select the curve to trim to.
You can get some description on that line up to 31 characters as shown in Figure 1 below. The full material description should be in the material definition window as shown in Figure 2.Figure 1Figure 2
Patric,Welcome to the forum. You want to be able to add material to the pipe while keeping the holes the right distance from the ends of the pipe? The best way to do this is with relations. I've attached some images to help facilitate visualization. When you create a double sided blind pipe, go to the Feature Information for that extrusion, and you will see some parameters, such as d0, d1, etc. When you make the holes at the end of a pipe, make the dimension for that hole from the datum plan with relations. The example I used is I want the holes to always be 0.5 inch from the ends of the pipe. When you place the pins in the holes in the assembly, you will have to make sure the pins are constrained with the hole so when you change the pipe length, the pins will move with the holes.
Example attached.
See Page 7 in the attached file.
Abilash,The IDD instructions for Creo 1.0 are attached. This should help some.
If you want to use the same name, delete the directory that stores the results.
It's easy to make intersecting curves at the assembly level, as long as the surfaces were created at the assembly level (shown below). But if you want to copy-and-paste a surface from one of the components in the assembly and put that copied surface at the assembly level, you will have to use Copy Geometry. I copied part of the dummy plate surface and the copied geometry appears in the model tree as Copy Geometry id 232, and this surface is at the assembly level, which can be intersected with other surfaces at the assembly level.
Tommaso,PTC says you can, and here is their response, but I couldn't replicate it for now. PTC stated:"You can create a curve using Intersect at the assembly level. To create the curve you will need references that are valid. For example if you are trying to show an intersection curve of multiple parts in one feature, a surface will need to exist that represents all the parts, which may require some trimming and merging. Another method that you could use to accomplish a curve through multiple parts is a curve through cross section, which is a right click option from the section in the model tree or view manager."I've requested a live webex session tomorrow for them to demo this.
It works well if you can open up the component and create the intersecting curve at the component level. You can then use that intersecting curve to trace on.
Bjorn,I believe your attached file is a Student Version of Creo? A Student Version cannot be opened in a Commercial Version.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.