Skip to main content

Filter by idea status

Filter by product

6851 Ideas

Fix Modernized Project and Offset Tools in SketcherDelivered

1. Describe your environment: What is your industry? What is your role in your organization? Describe your stakeholders.Product design studio, I'm a senior designer.2. What version of Creo Parametric are you currently running?9.0.1.03. Describe the problem you are trying to solve. Please include detailed documentation such as screenshots, images or video.The Modernized Project and Offset Tools in Sketcher is proving to be very time-consuming as it adds many clicks to perform operation that used to be very fast.Projecting or Offsetting a loop until Creo 8 used to require 2 clicks to select the command and Loop, then 1 click per loop. Now in Creo 9 it takes 4 clicks to set up, 1 click per loop plus 1 click to confirm each loop.And, each loop is treated as a single entity where I cannot delete one or more segments of it using Delete segment, which again adds the time-consuming operation of deleting the loop and re-Projecting it as a partial loop.I understand you're trying to improve this command, but I think you should take a better look at all the possible usage scenarios before implementing such a big change.4. What is the use case for your organization?The new Sketcher features are proving to be unnecessarily time-consuming, our work takes longer with no apparent benefit.5. What business value would your suggestion represent for your organization?It would make work lighter and faster.

Supporting in Creo Parametric created trapezoid cross sections in Creo viewAcknowledged

Please include detailed documentation such as screenshots, images or video.1. What product and version are you running?Creo parametric 8.0.10.0 and Creo view Creo View 8.1 and Creo view adapters 9.1.0.0 2. What is the problem?Trapezoid cross sections are used by production department to see details within the assembly but in Creo Parametric created trapezoid cross sections are displayed incorrect and make cross sections in Creo view unusable (The internal details are red and unclear) 3. Are you using a workaround? If yes, please describe it.PTC recommended add a planner section for each plane and show the details in this but this is not wanted work around 4. What is the use case for your organization? Describe how your idea would work in context or how it would apply to a practical situation.Creo view should show the parts in details when you are creating a Trapezoid cross section in Creo Parametric. PTC acknowledged the limitation in my PTC case and R&D will consider an implementation in functionality without committing to a future release.5. What impact does this problem currently have on your organization? (Number of users affected, hours of lost productivity, etc.)It is not possible right now for engineers to help the production department with clarifying details within the assembly. Because these cross sections can not be used it is harder for production to find the details in assemblies which will cost search hours for the production department and more communication is needed between production department and engineering department. That this is not supported is as PTC also acknowledged a limitation of Creo view.         

A Creo parameter of the working directory pathAcknowledged

1. Describe your environment: What is your industry? What is your role in your organization? Describe your stakeholders.Design systems / assemblies to address client challenges - from initial concept to delivering final product.2. What version of Creo Parametric are you currently running?83. Describe the problem you are trying to solve. Please include detailed documentation such as screenshots, images or video.A system Parameter containing the working directory path would allow a drawing to be 'parametrically' documented with the directory file location in which that drawing was developed.   A requirement of some quality control procedures is to know and record the file directory of the source of the document.  A Creo system parameter that can be accessed within a drawing would allow this to be parametric instead of having to enter the path manually.  This would be a 'Creo' system parameter - available within drawings without the use of any product data management.4. What is the use case for your organization?Currently, the entry of data indicating the working directory path is a manual operation.  This could be automated and better serve quality control procedures and proper documentation5. What business value would your suggestion represent for your organization?Minimize and assure adequate documentation is timely and accurately available within the design and documentation phases of a project.

On CREO Illustrate to keep the balloon positions and only add new balloons to new parts.Delivered

Please include detailed documentation such as screenshots, images or video.1. What product and version are you running?CREO Illustrate 10.12. What is the problem?When generating illustrations using Creo Illustrate connected to Windchill, the software automatically positions the balloons of the exploded view when a new illustration is created. This positioning usually needs to be adjusted to meet the requirements for generating catalog images. Once the balloon positions have been defined and the images generated, the project is archived in Windchill.The problem occurs when updating the project to a new version. When a change is propagated from upstream to downstream, and the illustration is opened in the new version, the balloon positions defined in the previous version are lost for all parts, discarding the work done in the previous version.The suggestion is to keep the balloon positions and only add new balloons positioned by the system to new parts. Currently, all balloons are repositioned, requiring complete rework.3. Are you using a workaround? If yes, please describe it.There is no workaround to avoid the problem.4. What is the use case for your organization? Describe how your idea would work in context or how it would apply to a practical situation.5. What impact does this problem currently have on your organization? (Number of users affected, hours of lost productivity, etc.)

Allow use of a center-radius circle instead of a spline when creating detail views.Acknowledged

Based off the discussion here:http://communities.ptc.com/message/186964#186964When defining a detail view in Creo Paramentric 2.0 M010's drawing mode, the current requirements are : 1. Select a center point on the drawing you wish to create a detail view of. (One click)2. Sketch a spline that encloses that point. (Minimum four clicks)3. Select a center point to place the detail view.I have a number of objections to the spline as the default method of defining the area of a detail view.1: As written, the operation currently requires at least six mouse clicks.2: It is difficult to generate a smooth looking spline that does not result in messy view boundaries without sketching a draft circle and laying the spline down on top of that.3: The center point of the view can't be attached to a space in between two features so that it shows both of them without defining an extra point or (maybe) construction geometry.4: The preferred option for a detail view boundary (at least on my end) is the ASME circle, which is generated by Creo based on the dimensions of the sketched spline instead of directly defined by the user.  Unless I take extra time and at least double the number of minimum mouse clicks for this operation, the actual boundary of my detail view will not match with the shape or exact proportions of the ASME circle.What I would like is the ability to use a center-radius circle (2 clicks) as the default way of defining a detail view, with the option to use a spline or better yet, predefined draft geometry or an in-model sketch as an alternative way of defining the detail view boundary.  A circle would also eliminate the need for a separate click to define the detail view center in the base model, and would ideally eliminate the need for the circle to be attached to a particular edge or feature, so I can have the view centered on the middle of two evenly spaced features without taking extra steps to create something the current tool can pick up on.  As an added benefit, the dimensions of the detail view would be exactly proportional to the boundary of the ASME circle and would show everything visible inside the circle, eliminating unnecessary visual noise caused by an uneven detail view boundary and making sure that any other features that might be included in the detail view are reproduced exactly.The proposed change would result in a minimum of three mouse clicks necessary to define and place a detail view in drawing mode.  Do note, I don't want to get rid of the spline, I can see it being very helpful for complicated parts, but I would rather take an extra click to select a spline, since I'll be wanting to make a more complicated boundary anyways, than take the normal minimum six clicks to define a spline and four clicks if I want a circle instead of the default spline.Either way, however, would be better of the current alternative of 2 (draft circle) + 1 (center point) + 8 or more (sketch spline on top of draft circle) + 1 (place view) + 2 (double click correctly or 3 to select the view in the drawing tab, right click, properties) +1 (select ASME circle) = 15 or more clicks to get a detail view with a smooth circular boundary that displays the ASME circle.  Again, this operation could take three clicks. 

Creo Cabling - Devices with pigtails and Pre-Fab cable w/o FT instancesUnder Consideration

A functionality that would make Cabling excel would be to enable support for Devices with Pre-Assembled "Pigtail" wires/cables and Pre-fabricated cables without the need to generate new instances every time they are added to a new assembly.   Take for instance a Sensor or Surge Protection device that is sold with 18" conductor leads.  Instead of modeling the wires in Creo Parametric, I would like to define the pre-assembled wires as Entry csys where I can predefine all of the parameters including the addition of "MAX_LEN"  Then when added to a Cabling Assembly, it should become its own harness and if when routed the length is longer than "MAX_LEN" then route would fail do to this.  In this way, there is no need to create a family table and new instance for each application.   Same would go for Pre-Fabricated cable assemblies.  The connectors on each end should be dynamic so that one could assembly each independently and the Cabling application could leverage same logic above the cable in between is routed.    This is functionality I do not believe any other Schematic to 3D solution offers and yet it should be a requirement for all of them as they are so many devices and pre-fabricated cables that are supplied this way.  Attached is a pdf of a Surge Protection device that I commonly use. Note in figure one, the pigtails.  It does not make sense to model wires for each application or at all as the position of these wires is infinite.   Patch cables are the exact same.

Email Authoring AssistantImplementation In Progress

1. Describe the specific problems or pain points that this tool aims to address. What challenges does it solve? Could be more than one. Email is the prime communication channel during case management, and it is sometimes a struggle to write clear and structured emails to customers, being at the same time empathetic and easy to understand for the recipient 2. Provide real-world scenarios or use cases where your tool would be beneficial. How do you see users incorporating it into their workflows? As a TSE writing a communication to the customer about a case, I want some authoring assistance so that my email complies with communications guidelines (positive language, empathetic, etc.) 3. Identify primary processes that will directly benefit from this tool. Case Management4. Identify the primary users or target audience for this tool. Who will benefit the most from its features? TSE5. Estimate the potential business value and impact of implementing this tool. Quantify as much as possible. For example: "TSAMs would save 30 minutes each week", or "TTR for cases would decrease by 1 day." TSEs would save 1 minutes for each email sent6. If you have any preferences or ideas regarding the tool's user interface, provide them here. the TSE enters a draft text with key ideas and a draft would be generated for them to review, enhance and paste into their email application before it gets sent to the customer7. Include any extra details, suggestions, or considerations you think are important for evaluating your idea. Ideally the tool should be embedded either in Salesforce or in Outlook

Sheetmetal Flat feature can't bend 180 degrees (Flange works)!Acknowledged

1. Describe the Problem Reference: Article - 419866 Ticket - 17339489    A flat feature is not able to be bent a full 180. As the bend value grows larger and larger to 180, the flat distance stops referencing the reference edge of the part. Rather, it starts to reference a point in space and then stops working altogether when it gets close to 180. A flange has no issues bending to 180. See video:(function() { var wrapper = document.getElementById('lia-vid-6354757664112w962h540r176'); var videoEl = wrapper ? wrapper.querySelector('video-js') : null; if (videoEl) { if (window.videojs) { window.videojs(videoEl).ready(function() { this.on('loadedmetadata', function() { this.el().querySelectorAll('.vjs-load-progress div[data-start]').forEach(function(bar) { bar.setAttribute('role', 'presentation'); bar.setAttribute('aria-hidden', 'true'); }); }); }); } }})();(view in My Videos) 2. Are you using a workaround?The engineering design team struggled to get the geometry they were hoping for. Many user's see a flat and flange as interchangeable and thought there was an issue with the tool to create the geometry. We are confident that most user's will not remember to use a flange feature, if they see this issue in the future.3. What is the use case for your organization?The design requires the sheetmetal to be bent at 180degrees (all bent back).4. What impact does this problem currently have on your organization?This slowed down and limited the design process, as there didn't seem to be any logical reason why a flat couldn't be bent 180 degrees.

Adding a location from a point to a Flat Ribbon should not introduce twisting!Acknowledged

1. Describe the Problem Please reference: Article: 360568 Ticket: 16206056 SPR: 13491483   We created geometry points on a sketch such that we can help route a ribbon cable thru those points within the cabling module. When trying to add location, and specify those points, the ribbon becomes twisted. According to R&D, this is per design as the path of the ribbon will be parallel to the sketching plane that the point was created on. Where-as, if it was a regular datum point, it simply goes thru the point, like you would expect. If we were sketching, we would need to do it on a plane that is perpendicular to the direction we want the ribbon to travel.    This is not ideal for many reasons, including: I don't believe this concept of a direction being dictated by the reference plane of an object was ever used before. Up until we had PTC write this article, it was unknown. A typical user would not think this is how it should behave, based on how the tool behaves in other situations. If we had to create a sketch perpendicular to the direction of travel, we would need to create many sketches. It is much easier to create one sketch with multiple points for the ribbon to travel through. This adds unnecessary complexity and confusion, making it even harder for the user to try and use this module, as intended, instead of using the regular module with a few simple sweeps.   2. Are you using a workaround?We don't use the cabling module much, especially for ribbons, because of it's lack of being user-friendly and inconsistent with work-flows.3. What is the use case for your organization?We would like to have our 3d designs be as accurate as possible, including wiring, cables and ribbons. However, instead of modeling with sweeps in 10 minutes, it took us much longer trying to deal with the issues of 'twisting' with the ribbon.4. What impact does this problem currently have on your organization?Almost all user's won't go near the cabling module due to this and many other similar issues regarding it's user-friendliness (or lack-there-of).

Create Scaling Anchor Points on Broken View Break LinesAcknowledged

1. Describe the Problem When creating broken views, depending on the size/scale of the view and the geometry involved, selecting the Heartbeat or S-Curve Options for the Break Line Style often results in a comically oversized break line that is unusable.  The workaround is to sketch a spline in the size and shape you want, but they never look as nice as the pre-defined geometry.   If a couple of anchor points could be added to the break lines that would allow you to scale the height and width of the break lines, it would be much cleaner and easier to use these break line styles.     For example on the heartbeat style, an anchor point at the point of the heartbeat could be used to grab and drag to scale the height/amplitude of the heartbeat and another at the end could be used to grab and drag to adjust the scaling of the width/wavelength of the heartbeat.  Perhaps a 3rd could be added to allow you to drag its location and snap to various geometry points or freely along the break line.  Similar could be done on an S-curve style break line.   2. Are you using a workaround?Satisfactory results may sometimes be achieved by using a spline sketch or playing with the scaling of the view. However, the spline sketch doesn't always look as clean and the scaling can't always solve the issue.3. What is the use case for your organization?We encounter this issue often when creating broken views of longer pieces of material (a piece of square steel tubing for example). We prefer to use the heartbeat or s-curve styles, but they are often unusable when selecting them in the drawing view dialogue box.4. What impact does this problem currently have on your organization?Lost time spent fiddling with view scales, break line locations, and spline sketches which could be as easy as a few clicks.