Recently active
1. Describe the ProblemUnable to control the visibility of surfaces and curves (datum curves and sketch curves) on the shaded drawing view by layers of the drawing side in Pro/ENGINEER.2. Are you using a workaround?3D pdf or creo view, format but not possible for all customers and need external application to customise pdf format3. What is the use case for your organization?The display of datum curves and surfaces in the shaded view of a drawing depends on the model or assembly visibility. ptc article describing the issue CS43026 and organisation case4. What impact does this problem currently have on your organization?need external application and productivity loose to obtain the best result: 2 to 3 month for customisation with test Windchill is needed to automatize pdf files etc... dévelopment costs These new fonctionnalities will be good to simplify other case: specific surface, 3d curves for shaded view in drawing many thanks
1. Describe the Problem For all situations the user edits a Creo material or material assignment we run a custom logic via "Creo Parametric Object TOOLKIT Java Free API". Hence there is no way to get the information from Creo when the user selects "Cancel" in the respective Creo dialogs and does not chance the materials at all. In this case we don't want to start any actions via "Creo Parametric Object TOOLKIT Java Free API". Therefore we need a way to get the user selection (OK, cancel) of the commands ProCmdMmEditMaterial and ProCmdMmEditMaterials ideally in "Creo Parametric Object TOOLKIT Java Free API" (JLink).This problem had also been reported in C17514420 with the result: "There is no supported API to do that".With this Idea I'd like to ask for implementing new functionality in "Creo Parametric Object TOOLKIT Java Free API" (best case .. or Toolkit if this is not possible). 2. Are you using a workaround?The workaround is to parse th
1. Describe the ProblemWhen stacking drawing tables side by side or on top of each other, the readability will be improved if it was possible to have the outer border of each table represented with a thicker line as compared to the inner lines of the table. In Creo Parametric 10, it is possible to change the line thickness of the entire table using "Format > Line Style > Modify Lines" and then select a random line in the table, but this will affect innner lines as well as outer border of the tabel. At this point it should be possible to select either an internal line or border line and have the format change work only on the lines of that category.2. Are you using a workaround?Some users are placing tables with a small distance in between, but visually that looks ugly.3. What is the use case for your organization?The idea would increase the quality and readability of output from drawings, e.g. PDF output4. What impact does this problem currently have on your organization?Easier f
1. Describe the Problem Reference: Case - 17509073 SPR - 15725772 Article - 428088 Often, when importing an EMN file in to an existing assembly, one of the components gets replaced. During that process, it removes component level parameter that was on the original component. For example, we use the component level parameter LINENUMBER. This parameter is critical as it is used for Windchill line numbers BOM. Often, we have an ECNs where there was an in-line BOM change from one resistor to another. When trying to update the CAD, and using IDF collaboration, the line number parameter gets deleted and we have to manually add it back each time. Please do not have component level parameters deleted on a collaboration replace. 2. Are you using a workaround?Manually readding the parameters each time.3. What is the use case for your organization?See above in the description.4. What impact does this problem currently have on your organization?It slows down ECN CAD wo
1. Describe the ProblemWhen following a master modeling technique in Creo, creating a drawing of an assembly composed of parts from different bodies does not support automatic dimension retrieval. This forces users to manually add dimensions to the drawing, which contradicts the efficiency expected in a model-based design process.Proposed Enhancement:I request the ability to show dimensions for imported geometry in assembly and part drawings. This feature would enable users to automatically display the associated dimensions from the model geometry, similar to the “show dimensions” feature for standard models. This enhancement would significantly improve the integration and usefulness of the master modeling technique, eliminating the need for manual dimensioning and streamlining the design workflow.2. Are you using a workaround?No. Currently, users must manually create dimensions for assemblies and parts derived from body geometries, which is time-consuming and prone to errors. Incorpor
1. Describe the Problem Reference: Case - 17494178 SPR - 15684520 Article - 426936 There are many situations, while working in Design Exploration, where items in a checkpoint are flagged as 'modified' accidentally and added to the Design Exploration Session. When working with Windchill and/or Family Tables, this could end up causing a lot of future problem managing that checkpoint and pushing out the design to a regular Windchill connected session. Logically, it would make sense, that if an object is deleted from a checkpoint, that it would also be removed from the Design Exploration Session. Then, we could add it back into the checkpoint, unmodified, and continue working in the checkpoint. However, that is not what happens. DEX still tracks the changes to these models, even if they are no longer in the Creo session. There are now no workarounds to clean up a checkpoint that has modification issues besides rebuilding the checkpoint from scratch. If the whole point of
1. Describe the ProblemUsers can't scaling model with different factor on 3 axis with Scale model Feature included in Creo Parametric. 2. Are you using a workaround?the wrap feature can be used to do this, but it seem much easy to include this option in the Scale Model Feature.3. What is the use case for your organization?customer demand4. What impact does this problem currently have on your organization?customer demand
1. Describe the ProblemThis is an improvement proposal for GD&T Analysis .To improve user experience, All dimensions in the Stackup Details Table are appended with balloons in the drawing area to make interpretation easier,Afterwards , When the tolerance analysis is completedall Stackup Details Table should be exported to EXCEL table (.xlsx)2. Are you using a workaround?No workaround available.3. What is the use case for your organization?Standard designer's work, modifying and validating dimensions using GD&T Analysis.4. What impact does this problem currently have on your organization?When the model is complex or has a large number of components, selecting too many dimensions will make identification difficult when using tolerance analysis. Exporting the results table to xlsx format will also make the result information more convenient for field personnel to use.
Please include detailed documentation such as screenshots, images or video.1. What product and version are you running? Creo Parametric 9.0.6.0 connected to Windchill 12.2. What is the problem?With Extremely Large Assemblies, the expand all button in the ribbon must not be used as it induces a download of the entire structure into the workspace with a resulting very large cache (+100GB). We would like to find a way to hide this icon in user interface. It would be nice to enable all the icons in this area of the Creo interface to be customizable for the user to hide/turn on. 3. Are you using a workaround? If yes, please describe it.There is no workaround except hope the user does not select this when working with a large assembly that depends on simplified reps4. What is the use case for your organization? Describe how your idea would work in context or how it would apply to a practical situation.Not having this icon viewable would prevent the user from making
1. Describe the ProblemHi there, currently Creo Parametric provides a bunch of export formats like STEP, IGS, PVZ, STL, etc.What is missing, is a web friendly format like GLB, GLTF, USD and so on. 2. Are you using a workaround?no3. What is the use case for your organization?The file formats listed above could be used to generate a more immersive user experience with 3D web content for our customers compared to still images.4. What impact does this problem currently have on your organization?hard to tell
1. What product and version are you running?Creo 9.0.5.0 Windchill 12.1.2.12. What is the problem?We are currently unable to clean up the MBD Dimensions the way we could in 2D drawings3. Are you using a workaround? If yes, please describe it.No4. What is the use case for your organization? Describe how your idea would work in context or how it would apply to a practical situation.Please find the below (Image)details regarding the current situation with the MBD models:The combined states contain a large number of MBD 3D annotations (dimensions) scattered across the 3D model. These dimensions are not organized properly, making it difficult to manage.There are multiple combined states within a particular MBD model, each containing numerous annotations.Currently, users are spending a significant amount of time manually cleaning up the MBD annotations, which is proving to be a challenge and impacting productivity. We need an automated solution to streamline this process and make the dimensi
1. Describe your environment: What is your industry? What is your role in your organization? Describe your stakeholders.Not relevant to the subject idea2. What version of Creo Parametric are you currently running?Not relevant to the subject idea3. Describe the problem you are trying to solve. Please include detailed documentation such as screenshots, images or video.We have seen this specified as a contract deliverable requirement for defense contracts. There is currently no way to geometrically represent the LMC or MMC in Creo Parametric. The LMC and MMC states could be represented by transparent overlays or by separate representations. The nominal dimension must not be changed in order to illustrate the LMC or MMC state.4. What is the use case for your organization?In order to support design reviews and detailing using Model Based Definition, Creo Parametric should be able to illustrate LMC (lease material condition) and MMC (max material condition) based on defined
1. Describe the ProblemWe need to be able to solve generative design on a single component that is within an assembly. I am aware that this will require adding contacts (at least bonded) for components in the assembly. It is very difficult, time consuming, and error prone when taking an assembly where a component is supporting multiple other components and convert that into a single component with multiple point masses and loads.2. Are you using a workaround?The workaround is to use other topology optimization software where assemblies are able to be used.3. What is the use case for your organization?The most basic example is a bracket which is supporting a few components. If you could include those supporting components and their material definition into an assembly, it would be far easier than trying to set up a system based on a single part.4. What impact does this problem currently have on your organization?The impact is that it takes users out of Creo Generative and leads to peopl
1. Describe the ProblemYou are editing dimensions, you can see that 68 dimension is Locked because it is red, but you cannot see that 70 dimension is "driven by relation" since you try to change the value. I propose to give a different color to dimensions "driven by relation", and give a message when you mouse over it. Thank you2. Are you using a workaround?When you go to edit the dimension, you get the message that "dimension is driven by relation"3. What is the use case for your organization?We work with models that are created by any user of the Company, so you do not know which dimensions are driven by relation and which not, when you are changing dimensions.4. What impact does this problem currently have on your organization?The impact is for all the Companies that use dimensions driven by relation, that is a usual practice.
1. Describe the ProblemWe are working on Pro-Piping automation projects using SmartAssembly. But we have limitation to automate in pro-piping module as there are very few API's available for different functions.2. Are you using a workaround?So currently we are using UDF method as a workaround to create pipeline. However we are asking user to manually create the Solid Pipe once pipeline is created as it is not possible using UDF or Mapkey. We also tried using Mapkey to execute other functions in Pro-piping Module but it is not effective.3. What is the use case for your organization?So Basically, We plan to automate the pro-piping activities in Creo using SmartAssembly which will be only possible if API's are made available. This will ease the daily repetitive tasks of creating pipes. In our organization, different Business work on Pro-Piping projects.4. What impact does this problem currently have on your organization?Productivity impact due to more manual work which if automated can sa
1. Describe the ProblemProTextStyleFontGet() returns PRO_TK_GENERAL_ERROR, if the text is having a mixed font.If Creo-Parametric allows you to set the Font on individual characters, then there should be an API to read the Fonts for each characters or at least by grouping the characters of Mixed fonts. 2. Are you using a workaround?No, there is no workaround to get the mixed font from the text style.3. What is the use case for your organization?We are reading the Font of the Text and applying the same font to the text in our application, so that user see the correct Text style in our application4. What impact does this problem currently have on your organization?Since there is no API to retrieve the Mixed font name of individual characters, Mixed font text strings are rendered using single Font which creates inconsistency with Creo Parametric visualization
1. Describe the ProblemHi, I am planning to use Creo 3d model to embed in website design, need Suitable formats like GLB and USDZ. Need direct export options from 3d and also from the AR model generated. 2. Are you using a workaround?Trying to use step file to convert the files in other software but didn’t like the compatibility of it as it looses the environment setups etc3. What is the use case for your organization?It will be a helpful option in future for many industries4. What impact does this problem currently have on your organization?Not impacted at the moment but can added better user experience
1. Describe the Problem I am working in a software company. Our customer wants information about the semantic surface finish; however, we do not have sufficient APIs for it. We request the addition of APIs for surface finish information, such as MATERIAL and LAY_AND_ORIENTATION. All the properties we need can be set via the UI in the attached image. 2. Are you using a workaround?We are now using ProSurffinishValueGet(). However, it can get only double value set as roughness_height, which is defined in .sym file.3. What is the use case for your organization?convert to our file format.4. What impact does this problem currently have on your organization?We are unable to save sufficient information in our formatted files.
1. Describe the ProblemWhen a drawing of a harness is made and views need to be BROKEN VIEWS, the cables shown will not be solid. This is what creo looks like while setting up the broken view and this is what it looks like when complete. (no solid break)we would like to see them treated like solids that have edges. 2. Are you using a workaround?no not at this time, but you can manually sketch some lines and relate them to the view.3. What is the use case for your organization?creating harness drawings that are really long are truncated4. What impact does this problem currently have on your organization?minor issue but starting to get pushback from manufacturing.
There was a time in which skeleton model could not be a family table; now it is possible, but why flexibility (very similar to a family table "on the fly") is not ? Not possible to define or predefine a Flexibility for Skeleton Models If a skeleton model is opened, access to >File >Prepare >Model Properties >Tools >Flexible mentions: the information is not available If right click is done on a skeleton model in an assembly, drop down menu does not give access to Make Flexible capabilityA workaround could be using a regular part as a skeleton model (in the past it was a common workaround to bypass the fact that family table function wasn't available for skeleton models); I don't know the reason for such limitation. I would use it to manage different assembly configurations without the need to create (and manage in Windchill) any instance and/or WTPart.This function will reduce the time spent in ma
According to PTC support Creo does not allow to display 2D representations of datum coordinate systems to conform to ISO 5459. Creo does not mark the CS origin of coordinate systems with one axis normal to the sheet/screen with extensions of the axes and a circle. For ISO conformance it is also necessary to be able to rename the axes (X1, X2, ...) (section 7.9 in the standard). It should also be possible to place the CS tag (possibly via show/hide annotations). The Creo (3D) coordinate systems already looks very similar to the 3D representation of datum coordinate systems in ISO 5459. The suggested improvements regarding the axes naming and CS tag placement apply to 3D coordinate systems also.
It would be great if there was a ModelCheck check that would catch the presence of unattached features. It would be great if this check could catch unattached solid features and sketch/surface features. For example we have a specific problem in MBD models where we create designated areas on a surface, that surface then has draft applied to it and the designated area is no longer "on" the surface. This can be hard to detect visually and having a check for it would be very helpful.
The new ModelCheck GUI in Creo 5+ is a nice enhancement over the previous GUI. However, by default not all info is display to users automatically which wastes time / creates extra clicks. There is a hidden config_init.mc setting MC_REPORT_SHOW_ALL_TAB that solves this problem. Please make this setting not hidden and consider making the default yes to use the helpful 'All' tab. See images below. Current: With hidden config_init.mc setting: MC_REPORT_SHOW_ALL_TAB YN Y Y Y Y
Apparently, if there is a shaded view in a drawing, and you generate a dxf, the shaded views are exported as images that the dxf uses. However, if you have windchill and are using the cadworker to generate the dxfs, those image files are not available to download with the dxf. Therefore, we need some way to check for shaded views in drawings before they are released and the cad worker generates dxfs. Thanks!
Actual functionality of SHEET_SIZE_INFO (Sheet Size Information) lists the number of sheets in the drawing and their respective sizes. We have a need to identify if different format sizes are used in the drawing to keep consistence with some of our internal processes that require that all sheet size are the same. Either to modify the current check SHEET_SIZE_INFO or to create a new one that mark an Error or Warning if different size sheets are used in the same drawing.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.