Recently active
1. Describe the ProblemAn option in Creo drawing for View outline size to ignore all the hidden geometry. Currently there is a hidden drawing option EXCL_CRV_FEAT_FROM_VIEW_OUTL=YES only applicable for hidden sketches. 2. Are you using a workaround?Can use partial view or Simplified Rep3. What is the use case for your organization?We create big assembly with copy goem. Its hard sometimes to manage view outline4. What impact does this problem currently have on your organization?Drawing is cumbersome
1. Describe the ProblemEnable User defined Fringe, Measure and Graph results - which are based on existing Measures.2. Are you using a workaround?Multiple Measure points, which is quite manual. Hard to find worst locations over model.3. What is the use case for your organization?Welding joints and weld fatique estimayes require results like Max Stress-Min Stress at point. Today there is no way to plot this kind of User result in Fringe over model.4. What impact does this problem currently have on your organization?Unable to verify the product performance with Creo Simulate.
1. Describe the ProblemCurrently users are not able to have multiple Gravity loads. Should one want to have 3 perpendicular loadsets with one Gravity load each and then use post prosessing (vary load sets contribution) to find load direction, that is worst case - then system blocks the approach. With forces one can run analysis as described.2. Are you using a workaround?Global sensitivity studies can be used, but this is slow and computationally expensive.3. What is the use case for your organization?Say one has an shaker table or simiar structure with enforced displacement, the solution estimate of worst case could be solved without need of dynamic time analysis.4. What impact does this problem currently have on your organization?Model validation takes extra steps. Time to market.
The suggestion is that have Creo check the size of the hole or feature and extend the centermark/axis offset as a percentage of that measured/defined size.Currently the lines are extended as much for small holes as for large holes.Only on a certain cases is there an exact match that pleases engineer, which now results in most of them manually resizing the centermarks or changing the drawing properties (which is again one-size-fits-all) 1. Describe your environment: What is your industry? What is your role in your organization? Describe your stakeholders.All industries using 2D drawings and documenting models that have holes.I'm an external consultant visiting multiple firms designing with creo, this question comes up everytime.2. What version of Creo Parametric are you currently running?Creo parametric up to version 9.0.1.0 as of posting this idea.3. Describe the problem you are trying to solve. Please include detailed documentation such as screenshots, images or video
I would like that Creo could paint the threaded hole with some color, like other 3dCad programs do: If the thread is painted, you can see at a glance which holes are threaded...or in a section you can see if there is enough thread... all this in shading style, now you have to change to wireframe or hidden line to check it. Thanks
1. Describe the ProblemAs of https://www.ptc.com/en/support/article/CS351946 the hole note token exclusively conforms to ASME standard Y14.5 section 1.9.5 and does not adhere to ISO 129-1 since it consists of a capital 'X' letter.In standard ISO 129-1 chapter "Repeated dimensions" it is stated: 'When a feature is repeated on the drawing, it is possible to simplify the indication of its dimension on the drawing by indicating:— on one instance of the feature, the nominal dimension (with a property indicator symbol if appropriate), preceded by the associated number of repetition, followed by a multiplication symbol (×) and a space (e.g. 2× ⌀18).Since this also applies to MBD hole notes, we Creo users cannot use the token that evaluates from HOLE_INSTANCE_X_SYMBOL because it always results in a capital 'X'.On the other hand, PTC claims Creos MBD features to be conforming to ISO 129 multiple times, and there is even a DTL setting for a similar requirement that also results in using the mult
Please include detailed documentation such as screenshots, images or video.1. What product and version are you running?9.0.5.0 and testing 10.0.1.02. What is the problem?ModelCHECK does not report many drawing centric 'things' that are obsolete to do in a Model Based Definition centric workflow. This includes existing drawing dimensions, number of parameters designated, unwanted symbols, unwanted relations, number of different kinds of notes (the default NOTE_INFO is not helpful as it's not distinguishing between shown parameter values in table cells and manually created notes (not) attached to models on the drawing), unwanted balloon types, unwanted balloon content, unwanted dimension text, update symbols from file, etc...When referring to https://support.ptc.com/help/creo/creo_pma/r10.0/usascii/index.html#page/model_analysis/modelcheck/Drawing_Mode_Checks.html then even regeneration errors, regeneration warnings, start parameters, parameters to rename et al. are not available in draw
1. Describe your environment: What is your industry? What is your role in your organization? Describe your stakeholders.We design and manufacture high-end electronics. I am the CAD Manager / PTC SME. Stakeholders for this idea include our Creo user community. 2. What version of Creo Parametric are you currently running?8.0.6.03. Describe the problem you are trying to solve. Please include detailed documentation such as screenshots, images or video. Reference Ticket: 16620599 When running modelcheck regenerate on the drawing, the drawing is not updating to the extent where any lost orientation references of a general view are not in the message log. We can't use modelcheck to flag that as an error. Only when the drawing opens do we see in the message log:"Geometry needed to orient the general view "new_view_1", on sheet 1, is missing."We would want modelcheck to flag this, but we would need it in the message log first.It does work when there is a lost reference for a detailed
1. Describe the Problem While detail drawings provide a way to save a table as an excel table, the formatting of the "save as" file is not sufficient to assure the excel table cells are accurate. If the detail drawing table has cells that contain a number, the letter "E", and more numbers - excel formats the cell as "scientific" or an exponential number rather than as 'general' or 'text'. An exported excel file should have sufficient formatting information to provide accurate data representation in the file opened in excel. 2. Are you using a workaround?Manually check every cell entry in the opened excel file. Re-formatting the excel cell as 'text' or 'general', looses the original content, so each incorrect cell must have the correct data re-entered.3. What is the use case for your organization?Easier and more intuitive use of drawing table data, without having to extensively check for and re-enter inaccurate file data.4. What impact does this problem currently have on you
1. Describe the ProblemRegular Creo users see a Bundle in their large scale assys and want to measure that Diameter, Currently there is no tool to do this. If they know how to edit the cabling info, they can dig, but this takes time. shrink bundles even have multiple diameters depending on where you pic the point. So I am asking for the standard analysis tool to be able to measure the diameter of the bundle for non-routed systems users, So they can design around it.currently you cannot select this cable feature to get the diameter that the Creo user needs to model around. maybe a special measure tool button can be used for this instead of Diameter.2. Are you using a workaround?They have to ask someone who routed it to get that info for them. They should not have to do this3. What is the use case for your organization?When regular Creo users need to design around the harness they cant get the diameter of the harness (because they are not trained in Routed s
1. Describe the ProblemWhen in wireframe mode, the two halves of cylinders are not considered to be the same surface by the ProSurfaceSameSrfsFind method due to the presence of dividing lines (see article CS112362). This is unexpected to us as one would presume the entire cylinder is the "same surface" even if dividing lines are shown.2. Are you using a workaround?No.3. What is the use case for your organization?In our product, which integrates with Creo, cylinders can be used as features representing geometry on the model.4. What impact does this problem currently have on your organization?Only half of a cylinder being made into a feature is unexpected behavior for the users of our product.
Create a configuration setting that allows the ability to turn on "Include quilts" by default when creating Section Views. Because welds are created as quilts if you do not remember to check this setting 2D views will not update properly. Welds that would normally not be seen in a section will show. If this was a simple configuration setting to turn on or off by default it would help to remove confusion as increase efficiency.
1. Describe the ProblemCurrently, hyperlinks in table cells (allowed only in comment cells) are not exported when the table is saved as an excel table. The table cell text is saved, but the associated link is not. The associated hyperlinks need to be included in the exported excel file.2. Are you using a workaround? This requires re-entering all the hyperlinks in the exported excel file.3. What is the use case for your organization?Hyperlinks in the exported excel file are a necessary reference for data verification and passing the information on to the next step in some production processes.4. What impact does this problem currently have on your organization?Time consuming data (hyperlink) re-entry and the introduction of unnecessary errors.
1. Describe the Problem We are using text parameters to fill out a revision table and to describe the revision changes. However, we have noticed that the current maximum text parameter length of 80 characters is insufficient for our needs. This limitation prevents us from fully utilizing the available space in the relevant cell and from providing detailed descriptions. Could you please consider increasing the character limit for text parameters to a much higher amount or even removing the limit entirely? This enhancement would greatly improve our ability to document revisions more effectively. 2. Are you using a workaround?No3. What is the use case for your organization?We are using text parameters to fill out a revision table and to describe the revision changes. However, we have noticed that the current maximum text parameter length of 80 characters is insufficient for our needs.4. What impact does this problem currently have on your organization?At least 12 users in our organization
It would save a lot of rerunning of simulations if you could add measures and recalculate their value from an already run simulation.I would also be useful to be able to query results at a specific node or location.
1. Describe the ProblemDetail drawings offer a way to save a table to an excel file. However, if the table extends onto multiple sheets, selecting the table only selects the portion of the table shown on the one sheet. There needs to be a way or option to select just what is shown on the sheet, or select the entire table, to save to the excel file.2. Are you using a workaround?Save a copy of the drawing. Open the copy, delete the table extents so it does not span multiple sheets. Select that table and save it as an excel file. This is faster than exporting (saving multiple excel files from multiple sheets) and combining them within excel. Either way is frustrating.3. What is the use case for your organization?Easier and more intuitive use of drawing data.4. What impact does this problem currently have on your organization?Additional project time.
1. Describe the ProblemCurrently hyperlinks can only be in 'comment' cells in a table. There is no way to have a hyperlink for a part or assembly available in multiple tables (such as two separate BOMs e.g. a Master BOM and a Subassembly BOM) that can provide part or assembly specific hyperlinks in the same manor as part or assembly parameters. If there were a parameter type for 'hyperlinks" within parts and assemblies, and a report parameter type for hyperlinks, then hyperlinks could be available in any table by using report parameters. This should be a requirement of MBD when creating BOMs for Assemblies.2. Are you using a workaround?No. It is possible to copy a drawing with one purpose of BOM table with the commented cells filled, to another drawing. Then import that drawing into the original drawing, re-organize the newly added table as needed (e.g. keep the original BOM sorted by part number, and modify the second BOM to be sorted my materials). This is time inte
1. Describe the Problem In some of my workflows I need to create specifically named points. The names can be fairly long and the default window size in the point creation UI does not allow visibility of the full name. It would be helpful to be able to re-size the name column in the UI to see the entire name without having to hover over the name and/or click into a point name and scroll with keyboard arrows. 2. Are you using a workaround?Yes, it is possible to hover over the point name to see the full text but this has to be done one by one for each point. You can also double click into the edit mode and scroll through the text with keyboard arrows, again this needs to be done one by one.3. What is the use case for your organization?Allow for quick reading of full list of points and their complete names, making checking for typos and consistent format easier.4. What impact does this problem currently have on your organization?Minor impact, just an annoyance that seems fairly strai
Add "solid_size" and "geom_size" to each model and make it possible to configure Creo to use these two new values as alternatives to "model_size" for determining drawing view sizes, text size of 3D annotations, and refit size."solid_size" would be the same as "model_size" except it would only consider solid geometry."geom_size" would be the same as "model_size" except it would only consider solid and surface geometry.We design a lot of models that are relatively small in size compared to the map part we are copying from. Because of this we are constantly having to set drawing views to "partial view" and draw a curve around them to keep the view boundaries from being enormous compared to the actual solid geometry. Also, the text size for 3D annotations is huge and the zoom refit button makes the model zoom out so far I can barely see it. If I were able to configure Creo to determine the view size, text size, and zoom fit function, based on the size of the solid geometry, it would save m
1. Describe the ProblemWe need direction of Ordinate/Baseline dimension direction.I have contacted PTC support and was recommended to submit an Idea to have an API for it.There is an existing API ProDimensionBaselinedirectionGet(), however API can work only with Baseline dimension type is DIM_LIN_BASELINE_PARALLEL. Please implement/enhance API to return non DIM_LIN_BASELINE_PARALLEL type Baseline dimension direction. 2. Are you using a workaround?PTC support confirmed there is no workaround at this moment.3. What is the use case for your organization?We would like to know ordinate/baseline dimension direction to analyze dimension.4. What impact does this problem currently have on your organization?One of feature in our product cannot work and produce incorrect false analysis result.
A highly customized Config.pro file can be confusing to manage and can become cluttered with duplicate entries - for both mapkeys and options. An option to specify a separate mapkey file would make managing these files much easier. This is even more important since the ability to have multiple sessions has been added. This would enable using different config.pro files for different sessions and easily use the same mapkeys. Regardless of the many possible post-installation work-arounds, this out-of-box solution would save a lot of (especially first time) users a lot of headaches.
Currently, many actions done in DRAWING mode cannot be undone.DRAWING mode should have full UNDO & REDO capability for all operations!
1. Are you using a workaround?Actually we are working as per PTC suggestion within CS322717: https://www.ptc.com/en/support/article/CS322717?source=search Workaround: Create a mapkey configuring default values of chord height, angle control and eventually step size just after having: 1. performed >File >Save as >Save a Copy, using *.stl file as format 2. and selected Customize Export2. What is the use case for your organization?We would like to define a company-wide export profile for stl formats. Currently we can only do this to a certain extent, as the chord length angle control and step size still have to be specified later. For all other export profiles, all options can be clearly predefined in the export profile and nothing else has to be entered later.3. What impact does this problem currently have on your organization?User intervention required, use of a mapkey instead of an export profile like all other export profiles.Describe the ProblemPossibility to define default
1. Automotive industry. Mechanical designer 2. Creo 7.3. When showing the diameter of a threaded hole on a drawing, the diameter symbol is shown in front of the diameter dimension. It would be better if an M or G, ... (depending on thread type) would be shown on in front of the diameter dimension. Now the diameter symbol has to be manually replaced by an M. If you forget to change the diameter symbol in the drawing, the drawing is wrong and bad parts are made.4. What is the use case for your organization?5. What business value would your suggestion represent for your organization?
1. Describe the ProblemThe sorting functionality in Creo 11 differs from the normal standard.Untill Creo 11 we named our top assembly with the prefix "0000_".By doing this, that assembly was always shown as the first file either in windows explorer or creo file explorer.This behaviour changed dramatically with creo 11 2. Are you using a workaround?Open the search function and tip in "0000" Then there is only one file shown.3. What is the use case for your organization?Our projects are structured in folders. All our users know, that the can easily open the top assembly just by pressing "Ctrl + O" and "Enter" Since creo 11 everyone complains constantly about opening the wrong files.4. What impact does this problem currently have on your organization?Affects everyone. It is anoying and not logical.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.