Recently active
For current functionality of Creo Elements/Direct Modeling, the only workaround is using Profile in Part Library, but is not very Efficient and not enough for design.Refer to https://www.ptc.com/appserver/cs/view/solution.jsp?n=CS166823&lang=en for detail
Precondition for the enhancement request The individual system color for hatches does not exist yet and should be introduced, see and vote for this precondition feature request here:Hatch color for sketches, cosmetic sketches, and cross sections.Currently (shown in Creo Elements/Pro 5.0, should be the same in Creo 2.0) all hatches are controlled by the "Letter" system color, which drives as well the color of other lines like dimensions and other auxillary lines:Introduce possibility to overrule all individual color definitions by the system color Make it possible that the hatch system color that has been set in the session overules the individually set hatch color.This dialog allows to set an individually color that should be possible to be overruled by the system color:The resultAll hatches have the same color in a drawing which can be a special color which is not used anywhere else on that drawing.
Improvement Request:In Creo Parametric 2.0 if you change the view state from one simplified representation to a different one alle BOM balloons in all affected views will be deleted.It would be a great improvement and would save a lot of work if the defined BOM balloons would not be deleted and instead kept and converted to all affected views.
When we see some error and the regenration status is red, we clicked on it and easly find the components which are failed in regernation. However we can not locate it in model tree from there. We have to note the component name and need to use look up tool to locate it in model tree. If any option can be introduced like right clicking the model in regeneration manager window and then locate in model tree, we can easly find the failed component and work on that. This option will be useful when handling large assemblies, otherwise it takes time to find the failed component among several components.Regards,Jayanta Sarkar
I know it can be done many ways however a direct option when creating extrusion will be very helpful. "Extrude upto offset from a surface"For example, when we create a plate which should have terminated before 10 mm from any surface. I need create two features. One extrusion upto that surface another cut 10 mm from that surface. One option "Extrude upto offset from a surface" will be useful and logical I guess.Regards,Jayanta Sarkar
It is standard functionality that, for example, in the menu "Rectangle" if "Slant" was the last selected tool then "Slant" appears at the top of the menu for the next selection.In the Machining menu this is not the case. Whichever tool was selected last (for example "Countersunk through hole"), this tool is not at the top of the menu for the next selection.The Machining menu should work in the same manner as the standard functionality and offer the last selected tool at the top of the menu.
At our company, we send the PCB engineers a drawing and an EMN file of the board assembly. The problem is that the dimensions in the drawing for the component placement is rounded to 3 decimal places, but the EMN goes out to 8. We would like the decimal places for the component placement to be controlled so the drawing and EMN are consistant.
it is logical that a section view or cutaway view are not possible for flat views, but it schould be possible to make it a broken view
There should be a standard functionaly of getting consildated piping length for each sizes for procurement without using any toolkit or special relations from 3d piping assembly it self. This is very basic requirement of piping.
Es sollte der Default-Name für die Roh-/Fertigteilbeziehung von rfbez1 auf z.B. sf geändert werden können. Dies sollte in den Einstellungen vorgegeben werden können. (heute: DE: rfbez1 EN: sfref1:)
The command "Curve From File" does not exist in the ribbon menu for Creo 2 Parametric. The commands associated with datum curves are located in the drop down section of the Datum group within the Model tab. Within the Datum group there is a curve fly-out menu for "thru points", "from equation", and "thru xsec". The option for Curve From File should be located here along with the other datum curve options. The default PTC groups cannot be altered to add missing commands, therefore a new group would have to be added to the ribbon to add this command. Creating a new group is easy, however this places the command outside the context of where it should naturally be located.
When inserting a drawing symbol from the symbol palette the variable text does not retain its state.The variable text is prompted on inserting the symbol - no ability to use dropdown menus etc.It would be great if the state of the variable text is retained from the symbol palette and/or the dropdown list is available during placement.
Need the ability to edit and add objects to the Promotion Request if user did not include all objects or if users miss spelled a word in description. Has to delete request and start a new one.
When creating a copy geometry (and probably other features that pull up another model tree) a secondary model tree pops up and allows access to the features within the other model. The problem is that the second model tree doesn't allow you to change to the layer tree. This has to be done with the first model tree (see images below). This is a problem because (as I noted in another product idea: Fix Useless Grayed Out Menu - Copy Geom) there are menus in the way of the tree so the tree has to be dragged out from under the menu. If the secondary tree controlled the layer menu as well then this wouldn't be an issue.
When creating a copy geometry and selecting features of a referenced model the "References" tab turns grayed out but stays in the way of the model tree, making it aggravating to negotiate and reference the model tree. Most aggravating. Can't the menu just disappear or collapse if the entire thing is grayed out anyway?? If I need to access the tree controls I have to drag the tree width out from underneath the menu just so I can get to the layer controls. Surely this can be easily fixed.
A colleague of mine tried to drive modifications using the 3D dims,but failed when he tried to use 3D dims in conjuction with clipping planes.The example underneath shows two dims, - one on the center of the part, the secondartifically placed next to it by splitting the edge of the inner circle and using the vertex as reference.When clipping this part all dims on the clippingget suppresed and thus not accesible for driving any modification on this part.My expectation would have been that at least dims on the plane would be visible , - better all dims going across the clipping plane also.
We have some Family Tables of PCB assemblies. We also use the EMN export functionality, which relies on the ECAD_REF_DES field to name the reference designator in the EMN file. Sometimes, the PCB guys have different reference designator names for the same components between the different board assemblies in our Family Table. It would be nice to be able to vary ECAD_REF_DES to the EMN export for each instance has the correct reference designator name.
Create options to customize individual settings for setup file of model tree (tree.cfg) for each model mode or save customize model tree with model (use template model).
Situation: Drafting mit dem DrawingManager gestartet. Es sollte eine Möglichkeit geben, im Drafting die Darstellung der Zeichnungsrahmen zu gestallten. Welche Rahmen sollen angezeigt werden. Anzeigetext definieren.. situation: Drafting started with DrawingManager (fluent UI). There should be a way to design the representation of the drawing frame in Drafting. Which frame to be displayed. Define the display text.
Where is L5 marking. It would be better if hole is auto generated in this type of bracings like base plates.
In the following operation, I can not save drafting data. I think it is "NOT" kind system for users. So I want "PTC" to enhance Drafting system in order to be able to save data. 1. Run the Drafting ( system gets the license) 2. Load data and modify the data 3. Think about design for more than 15 minutes It means that user stop using Drafting system (Drafting hold time is 15minute) 4. The license that Drafting system have got is released 5. Restart using Drafting system when there is no lisense that the user can use 6. The user have to finish Drafting without saving the data or wait until Drafting system get the lisence I'd like PTC to enhance in order to be able to save data in NO6 For your informatin, in case of Creo Elemet/Direct Modeling, user can save the data in NO6.
Step to reproduce:1 - Create a reference pattern in a part using an external reference from within an assembly.2 - Save, Close everything and erase from session.3 - Open just the part without any of the references in session.4 - Edit the first pattern member and add a geometry point.5 - The Geometry point does NOT propogate through the other pattern members, even through the pattern does regenerate and everything else works.PTC Support said this is NOT a bug but a feature limitation... so the only way I can get this fixed is posting it here and hoping someone reads it.
In case of Sheet Metal parts which have bends is needed specifying the modification surface,It is necessary to bend-back itself.
When we open the file.(in Creo Parametric 2.0)Cross section at the bottom of the model tree.We do not like the state in which it is expanded.I want to make a collapsed state.In addition, I want to set in config.pro.
Currently the file sizes generated when exporting a .PVZ from from Creo Parametric are much larger than can be generated using eDrawings. Quite often the file size in eDrawings is 10% of what can be achived when exporting from Creo Parametric with Out Of the Box settings. PTC can you please review this particular functionality to see if there are any ways to reduce the file size from within Creo Parametric itself. We have found that by editing the recipe files, the line for "adapter/dglTolPerc=0.2" compared well to eDrawings in file sizes, but this is too much effort for most users. Can we have a config.pro setting that make this easier? In eDrawings they have a slider bar which can be easily changed.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.