Recently active
Jeff,Welcome to the forum. In order to attempt to replicate the problem, you need to upload the model so we can open it in Creo 3. Error file shown below.
You have a lot of AutoGEM controls that are influencing the automesher. You're making long thin brick elements with hard points and the prismatic control. This will control the mesh in these regions regardless of what you set the aspect ratio to be, which in this model is 8. A very low aspect ratio will slow your run times. PTC recommends keeping the aspect ratio at 30, the default. The advantage of using the adaptive p-method is you have the ability to have high aspect ratios.There are a lot of exclusions too. This will only exclude from measure and not the fringe plot.What exactly are you trying to recover in this model?
Do you have an image that can be uploaded?
If you had set up a pre-defined measure to plot the stress convergence in the region of interest, you could tell if it was a singularity, because singularities do not converge.
Isn't Acetal a plastic bushing? You want to recover stress on plastic?
PTC stellte PTC Creo 3.0 vor, die neueste Version der Flagship-Entwicklungssoftware von PTC. Ob Sie die Software selbst ausprobieren, eine Online-Demo ansehen oder aber erfahren möchten, was andere darüber zu sagen haben – es gibt bestimmt die passende Ressource für Sie. Hier eine kurze Übersicht: http://ptc.co/BjPpo
Which assembly are you having problems with? Please see attached image.
PTC released Creo View 3.0 a few months ago in May 2014 and here are the next FIVE key updates/enhancements in this release. These are around Alternate formats, Creo View Adapters, Positioning Assemblies, Animation and CAE Visualization. This is the third post in a series of posts about What’s new in Creo View 3.0 M020.Refer to my previous posts below for details about the other things that are new in PTC Creo View 3.0 M020.Creo View 3.0 M020 Part I -Zoom, Compare, Measure, Edit and Touch.Creo View 3.0 M020 Part II - Selection, Drawings, Interferences, Markups and PublishingContinue reading
PTC released Creo View 3.0 a few months ago in May 2014 and here are the FIVE key updates/enhancements in this release. These are around Selection, Drawings, Interferences, Markups and Publishing. This is the second post in a series of posts that I plan to cover about What’s new in Creo View 3.0 M020. Stay tuned for my next post in this series….Refer to my previous post here for details about the other 5 things that are new in PTC Creo View 3.0 M020. Those are around Zoom, Compare, Measure, Edit and Touch. Continue reading...
In Creo 1.0 this appears to be impossible to do due to crashing at very vulnerable positions during the proceedure.You have a situation where you have a part that needs to be developed into a family table with sub instant parts that are related, but you may want to keep the original unharmed.You are already using the part in assemblies and sub assemblies.You rename the part to be the generic description, and add the part to the table, while having the drawing open. Save it before it crashes.You save the drawing, but only to find dispite a message telling you it has saved, that it is still looking for the original part, nextYou rename the ft generic description back to the original part to open the drawing. Replace the generic with the instance part, often crashes at this point,save it again, the drawing is ok.Next you open up an assemby with the original part, the whole thing fails because it cannot see the original part. You then rename the part so that the assembly can regenerate, ne
AV ENGINEERING a.s. uvolnila aktualizovanou lokalizaci na PTC Creo View a Illustrate 3.0Lokalizace je k dispozici v rámci aktivní služby manintenance.Pro bližší informace využijte kontaktní formulář na stránkách www.aveng.czDodávku a technickou podporu včetně školení PTC produktů v České republice zajišťuje firma AV ENGINEERING, a.s.www.aveng.cz
The below pipe was meshed with auto-controls. I didn't use any "guide lines" to make the mesh.
What do you mean mapped mesh needs "guide lines"?
In WF4, all fasteners used a spring idealization to model the bolt/screw. This type of idealization uses a 6x6 stiffness matrix enabling us to calculate the axial forces only, it did not account for any shear or bending forces (these are not defined in a spring). In Creo 2.0, PTC removed the spring idealization and replaced it with a Thimoshenko beam which uses a 12x12 stiffness matrix. This enabled us to calculate the axial forces as well as shear and bending forces. The results defined in Creo 2.0 are the most accurate, as the underlying idealization for the fastener better represents the condition. Along with the additional forces captured, the increased stiffness matrix provides more accurate results.
When you first start using family tables well, you see the entire world open up. You can make thousands of parts in seconds. Everything is great. Some time goes by, and you become more familiar with them. You have to change a parameter and realize you have to check everything out to propagate that parameter to every model. Maybe you start making family tables of family tables. Maybe you make family table assemblies. It's not long when you start to realize the bigger and more complicated the tables, the more trouble they cause. Especially when the people making them aren't as experienced and they are being used in many different uses.So the situation we faced were some of our engineers were using family table assemblies to make items that were not tabulated items. One example was a motor with different wire routing, Some were the same motor, some had different wiring options. Another case was using a family table assembly to create a simplified representation of a design assembly. The l
It sounds like when Creo 1.0 was introduced, the modeling and sketcher backgrounds are to be the same, according article CS111283. I opened a PTC case to verify this, and I will let you know what I hear from them.
Try running the model with no shells, and no surface regions, as shown below. I just ran a quick check with no poblem using solid elements, but different load. I did add some material to represent a weld. I'm running Creo 3.0, and I didn't account for stiffness for the bolts. Just make your model simple to start with to make sure it will run.
Ok, let's set the scene. Everyone is using Creo Parametric and Windchill without any problem. Sure some stuff isn't filled out completely. Maybe a datum (or a thousand) are showing. People aren't following standards, but they're not done yet. They'll get to it later. The models fail from time to time. Things don't look right. The computers start slowing down more and more. Now imagine the next day, it all changes. Datums are hidden on layers. Models are regenerating. They're named correctly. Data is filled out. What's the one thing that can start the change to having good data faster than a manager threatening to fire you?Gatekeeper.Gatekeeper verifies ModelCheck was run on a component, and based on the parameter you specify in Windchill will allow or disallow Creo Parametric objects from being checked in. Gatekeeper only verifies modelcheck parameters in the Creo models. Despite what people say it has no personality, it has no soul. It does not hate you. It is not evil. However, you w
Are you refering to the base where the tube connects to the plate?
Yes. If you check "Account for Stiffness" in the Fastener Definition window, you don't have to make two seperate runs to obtain the desired pre-load.
I recommend that you upgrade to Creo 3.0 so you can account for fastener stiffness. See below image.
The first thing I would like to know is what are you trying to accomplish? What is going to be your data of interest? Do you want fastener loads? Do you want stress recoveries in regions of interest?
What is the purpose of making all these surface regions?
Interesting. I've never had a problem inserting a .jpg file.
Jason,Here some simple instructions (see below image).
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.