Recently active
You can IMPORT the file with Creo Parametric 3.0 (F000). I've done it many times already. See my attached post on importing an entire H-60 lightweight model. This was made in CATIA V4.http://communities.ptc.com/message/257550#257550I just imported the entire CH-53E surfacing model from CATIA V5. I would post it here but I'm at home. I've also imported Solidworks.
I don't think Creo Simulate can perform impact analyses.
You would have to sketch the entire system, including the loads, in order for the community to understand your requirements.
This is how loads are applied in StressCheck, by traction, which is psi. StressCheck calls it a traction load, but it's really pressure. Just use a pressure load.
With a single p-element, the stress can vary from one end to the other.
If you have Creo 3.0, all you have to do is import it.
Is it not possible to create your own drawing template with the desired sheet size, and then all you have to do is load that template everytime you need it? I wouldn't need a config.pro setting for that. What do you think?
When you get the GUI to change units, it should look like the below image. If you have an assembly, don't forget to check "Include submodels".
How many elements are in the assembly?
I’m excited to announce that the call for presentations for PTC Live Global 2015, June 7-10, in Nashville, TN, is now open. And I encourage you to submit your proposal by November 17.Why should you present? You’ve heard a lot of the numerous perks you’ll enjoy, including a free registration to the event, the appreciation of peers for sharing your knowledge, the opportunity to be recognized as a top presenter, and the chance to connect with PTC product managers about your content.But there are other ways that you can benefit – both personally and professionally – from the experience that you may not have anticipated. We hear from past presenters that they also get feedback and new ideas from the users in their sessions that have helped them back at work. For example, Walt Brewer of PACCAR Inc., said:“The biggest benefit of being a presenter is the exposure and feedback I get from users who attend the session. There were…discussions on the complexities of the implementations, and i
Lucky,The load is not calculated in the attached model. It was predetermined by the user as 2000000 N and entered as such. The hinge acts like two cantilever beams, because the center of the hinge is constrained in global xyz. Even though you have Force/Area, the ends of the beams will bend and have less stress than the center, as shown below. If you want to understand how the load behaves (shear load), try drawing a shear/moment diagram on a beam with one end fixed and the other end free.
Can you upload a screenshot of the problem?
Charles,Amit already has another post on this. See the attached link:http://communities.ptc.com/message/259732#259732
I think what you're asking for is code verification. You want to verify if the code was developed correctly? You want to know the stress, strain, and displacement calculations based upon the finite element method.There are three components to solution governance when dealing with the finite element method:1. Code verification2. Data verification3. Solution verificationCode verification is the developer's responsibility. Data and solution verification is the end user responsiblity. Solution verification is by convergence on the data of interest.You can plot convergence on the data of interest, say to within 1%, to verify the solution. Validation would be by strain gage testing, to validate the FEA solution.To see if the attached model in this discussion "behaves" correctly:1. Plot the displacement and animate it2. Plot the desired stress/strain3. Plot solution convergence on the data of interest to within 1%If you want to attempt this by hand calculations, try a simple beam constrained
Can you upload the model?
Download from:https://support.ptc.com/appserver/cs/software_update/swupdate.jsp
What is the material type?Is this just an LDA on a block of material as you have shown?
1. Okay...that clarifies some things, because you did not mention LDA in your original post. You can still constrain the surface with a global constraint and fix the z direction. Then you will have to add more constraints to the other surfaces and select which directions to allow movement or no movement.2. The measure can be found as shown below.
Yes.
What do you mean by "load behavior"?
I don't know your load requirements. I was only showing you how to apply a bearing load, not a load on the bearing, as they can be different.In reality, bearings are usually press-fit onto a shaft, and that would give you an interference fit all the way around the inner race, which is a contact problem.If you know the pressure distribution on the inner race, then yes, you could apply the load to the entire surface as shown below.
Amit,I've attached a document from PTC that shows a bearing analysis (Slides 24 -41). I'm uploading this as general information, as there is more than one type of analysis in the presentation. I think you will this, as this will give you some insight to theory.
I made the below surface in part mode, and the Thicken Command works. I made the same in sheetmetal mode, and it didn't work. See below, as this is now activated.
This part is so easy to make, you could make a blend surface in part mode, thicken it, then flatten it in sheetmetal.
I would either make it all in sheetmetal to start with, or make it all in part mode as surfaces, thicken, then switch to sheetmetal mode.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.