Recently active
I checked all the logs in the following:1. Symantec Endpoint Protection2. McAfee Agent Monitor3. Computer Management/Event View/ApplicationI did find where the Creo application is "hanging" in the Computer Management Tool, but it doesn't give me the cause.
Am I suppose to have the latest VS2015 toolkit installed in the "prereqs" folder? As of now, I do not.
1. My account is not part of a local group.2. I don't know if anti-virus is blocking it.
1. If Creo Platform Agent installed, then I should see it in the programs list dated today. I don't see that, only two other Agents with different dates.2. creosvcs_64.exe does not want to run.3. I tried installing in "C:\Program Files\PTC", and I still get the prerequisite warnings for Parametric and Simulate.
I knew about that, but I didn't think this is what you were referring too.
Tom,I did that yesterday, but I'm just now reading the file today. I got eight hits on prerequisite, as shown below.
Run this? I try this after lunch.
"Application Installation" page? Where is that?
I attached it.
MH,I downloaded Creo 4 and unzipped it and tried to install it this way instead of using a CD. I received the same message "pending prerequisite" for Parametric and Simulate. But Platform Agent and Common Files installed.
Oliver,I was able to use the NAS624-28 based upon your instructions. Thanks.
I have Framework 4.5.2 installed.
Are you working with a student version of creo?
David,Here is a snippet of a portion of my Creo 4 license.
Oliver,I could not open the .mnu file in Step 4 in your instructions, due to the following messages:Are we supposed to use Reflection X to open these files?
Yes. I have a Creo 4 license.In your screenshot, you have Creo Engineer IV and Creo Advanced SE. I think I have just Creo Advanced SE. I will check again tomorrow.
Are you trying to install a student version?
You can make this with just two extrusions, or three if you want to use the chamfer tool. All linear dimensions are created from datum planes, not other features.
Thermal analysis is not supported in the Creo Simulate Lite version.
Oliver,I don't understand the first step in your instructions:1. Save your standard parts to a Creo "search_path"...I don't have Windchill.Can you explain this? Thanks.
Antonius,I think this is what you are referring too in the below image. The Sketcher CSYS will be grayed-out if there is no csys in the sketch for wrapped curves. Only the Center option can be selected. I had five wrapped curves, and when I first attempted this, I was using the Center option, but my curves were not aligning properly. So I had to places a csys in sketcher for each wrapped curve.
I had to create csys in sketcher for my wrapped curves on the rotor turbine, because they were definitely non-symmetrical.
You have to create a csys in sketcher mode that matches the csys of the hub. If you don't, the wrapped curve will be slightly off.
When using the Wrap feature for curves in sketcher mode, you have to make a csys in sketcher, otherwise, it won't work. It appears that you are trying to make a blade for a rotor turbine, then pattern the blade. On the last rotor turbine I made, I sketched 5 profiles at the csys, and then I had to wrap those 5 profiles on 5 different cylindrical surfaces. After that, I used the boundary blend tool to connect the curves that made up the blade, as shown below. Then I make a 360° cut to trim the outside. If I am reading your post correctly, the "wrapped streamlines" are similar to my wrapped curves on cylindrical surfaces before using the boundary blend and solidifying.
Jaspal,You can also select the surfaces in the model tree. LMB on the first surface, hold CTRL, LMB on the second surface. The intersect icon is shown below. Select it with LMB, and the intersecting curve will be created between the two surfaces and listed in the model tree.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.