Recently active
WF4 fastener tool is ONLY for two components, and if a preload is required, two runs are required to get the desired preload.
All of my product ideas and the link to submit a product idea has been removed. Is anyone else having this problem?
I think you would have to perform a transient thermal analysis to determine how much time it would take for the mold to heat up to 550-degree C. Here's some background information:
See the below instructions:
Square tubes may be easier to bend/unbend in Creo Sheetmetal, but I would like to know how you bend them in the shop?
Hi Davor,How did you apply the material properties for wood?
Hi Anand,Is this a Student Edition of Creo 2.0?Welcom to the forum.
Hi Jordan, Could you add the other components to your part to help facilitate visualization? It appears that you have a mechanical input of 4000 rpm on a sprocket on one end of the air plug. Is the bearing on the right side pressed into the sprocket or is the sprocket mounted separately to the shaft? The shaft is longer on the right side as compared to the left side. Both ends have a bearing which allow rotation of the plug, but then you have a sprocket attached somewhere. Correct? Do you want the part to rotate in the simulation? This problem statement is a little confusing to me, because you want to “block” rotation, but in reality the part is not “blocked”? Welcome to the forum.
Application and creation listed below:
While in drawing mode, did you select the image and RMB to show model annotations?
Jim,You can measure the diameter by using the method as shown below. You do this by:Analysis>Inspect Geometry>Radiusthen you can figure out the diameter.The surfaces of a sweep are always spline surfaces and not cylindrical surfaces. Therefore there is no diameter to measure.
Hi Jim,I looked at your file, and I was able to dimension the part in a drawing (shown below), however, as you already mentioned, you cannot measure it as a solid with the analysis tool. It appears that there is nothing wrong with the part. I will show this to tech support and see if a SPR needs to be generated to allow measuring the uniform sections after making a sweep with equal sections on the ends of the sweep.
The only way I know to bend and unbend a tube is what I provided in the attached thread, my rersponse on April 2, 2014: http://communities.ptc.com/message/237605#237605
For your general information, I would highly recommend working the attached document so you may know how a pre-loaded fastener really works in Creo Simulate. If you have not done this method properly, and confirmed the right pre-load, then there's no use questioning the results. http://communities.ptc.com/docs/DOC-5290Once the right pre-load has been confirmed, then run the model again with all external loads. This will be a total of three runs, two for the pre-load and one for the final.
If you are going to use a preloaded fastener, you must make two runs with just the fasteners. After you obtain the desired preload, then you make a final run with the external loads. What is the desired preload for the fasteners?
.
You may want to buy Pro|Engineer Wildfire 4.0 by Gary Lamit. Just search for it online. Amazon carries it, but it is in English.
There are 14 new tutorial videos on Creo Simulate 3.0 in the attached link:http://learningexchange.ptc.com/tutorials/listing/product_version_id:76
You will find some of the new major features that's coming in creo 3.0 in the attached briefing. This briefing covers creo 1.0 and 2.0 also, but 3.0 starts on page 14.
Hi Camron,You stated:"I don't know if this is the right way to come up with some margins but if it is then how can I find tensile force on my fastereners in creo results?"The tensile force for the fastener is in the run summary file. However, if your fastener has a preload, you have to run the analysis twice to get the desired preload. If you would like more information on this, I can provide it.
Hi Mayank, Do you want to run a static analysis in an assembly, or do you want an analysis just on the spring as a single component? Welcome to the forum.
Are you wanting the surface area of the elements that are subject to a given pressure?
This should have answered your question. Would you mark it as correct? This helps others when searching a topic with a solution.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.