Recently active
I don't know your load requirements. I was only showing you how to apply a bearing load, not a load on the bearing, as they can be different.In reality, bearings are usually press-fit onto a shaft, and that would give you an interference fit all the way around the inner race, which is a contact problem.If you know the pressure distribution on the inner race, then yes, you could apply the load to the entire surface as shown below.
Amit,I've attached a document from PTC that shows a bearing analysis (Slides 24 -41). I'm uploading this as general information, as there is more than one type of analysis in the presentation. I think you will this, as this will give you some insight to theory.
I made the below surface in part mode, and the Thicken Command works. I made the same in sheetmetal mode, and it didn't work. See below, as this is now activated.
This part is so easy to make, you could make a blend surface in part mode, thicken it, then flatten it in sheetmetal.
I would either make it all in sheetmetal to start with, or make it all in part mode as surfaces, thicken, then switch to sheetmetal mode.
I haven't used WF5 in a long time. I use Creo 3.0.
It looks like the original was made as a surface, but in your other post it's not, the one with a round feature.
If you select a valid surface, it will activate it.
I think that's why you're having trouble with the driving surface.
The Thicken Command is under Edit, as shown below:
Was this part made in sheetmetal mode? It looks like you have a round feature in the model tree.
Dale,If the sheetmetal was made as a surface, then you can thicken it with the Thicken Command (Figure 1 below). If the sheetmetal was made as a solid, you cannot use the Thicken Command (Figure 2 below), but you just assign the thickness during geometry creation.Figure 1Figure 2
You have to upload all the files that are in the assembly. You only gave me the top level. It's missing three other parts.
After you select Reply, select Use Advanced Editor. You will see a Browse button at the bottom of the message window where you can attach files.
David,I took a quick look at the geometry in the assembly. It appears that you have two planes of symmetry, and you could reduce the assembly to 1/4 for FEA. Also, there are too many small rounds that generate a lot of elements. I posted two images, 1/4 modeling and the amount of elements (3767 with default settings), if you wanted to keep it 3D.
You can upload the model, and I will look at it.
Amit,The attached image does not show anything about a bearing load or how to calculate a bearing load. However, when applying a bearing load in Simulate, it must be applied to a surface that is 360-degree (closed). Then you should Review Total Load, and this will calculate the load to see if you have applied the right bearing load.If you could upload some images of what your load looks like on the model, maybe we can get this resolved.
David,If you're on maintenance with PTC, then I would upgrade to Creo Simulate 3.0, which has LDA (large deformation analysis) with contact.
I think you can animate the motion in Creo Simulate after it has been modeled in Creo Parametric, meaning you can animate the displacement and capture it on video. I'm not sure if that's what you're looking for. Or do you want to model the flexible part of the suction cup and set it to motion in Creo Parametric?Welcome to the forum.
I don't know of any built-in function that will allow you to export results to Word.
Is this possible with any software?
Look at these three material properties for each material1. modulus of elasticity2. density3. poisson ratioand see if the are the same. You have Steel 1 and Steel 2, and these three properties are usually the same or nearly the same for steel.
If the Product Idea is something that Creo can already do, even if you have to make a few extra clicks, PTC will more than likely not consider it.
If you want to suggest software enhancements, I recommend you submit these as Product Ideas.
A file created in a Creo student version cannot be opened in a Creo commercial version. If you could upload some images of the problem, you may be able to get some assistance from the Community. There may be some users with student versions that can help. But I cannot open your file to see the problem.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.