Recently active
Scott,I submitted a couple of Product Ideas to help expedite the use of fasteners, but so far, PTC has not considered them. Ideas are attached below.Change fastener properties:http://communities.ptc.com/ideas/3784Copy fasteners:http://communities.ptc.com/ideas/3847Welcome to the forum.
Praveen, Thanks for posting.
War das seashell parametrisch, das in Creo geöffnet war? Wenn so, die Farbe und haben sind Sie versucht, das Modell zu schneiden grau? Ich denke, Sie angaben, daß dieses eine .stl Akte ist, die keine modellierende Geschichte hat. Werden Ihnen erlaubt, das Modell zu hochladen?
Stephen, I'm running Creo 3.0 M020, but not on a MacBook Pro, and I haven't experienced any of the problems in this thread.
Praveen, Thanks for posting the instructions.
Simulate works fine. I will take a look at the model in the morning. Someone may provide a solution before then. I just did a simple beam to verify my hand calculations, and it was perfect.Welcome to the forum.
Versuchen Sie, die unterschiedlichen Stücke des Modells dann des Druckes zwei zu schneiden, die mit vier Stiften verbunden werden können?
Pietro,Ich habe nie ein seashell gebildet, und es ist nicht sehr klar hinsichtlich, was Sie wirklich mit ihm tun möchten. Sie wünschen teilen das Oberteil und arbeiten auf ihm, in irgendeiner Form oder in anderen. Willkommen zum Forum.
The display of the datum axis in a drawing is controlled by the Show Model Annotations window. To show an axis:Select Show Model AnnotationsActivate the Datum Tab and Select AllSelect the desired axisThe below image is an axis in a cylinder in a 2D drawing.
You cannot open native student files in the commercial version.Welcome to the forum.
Could you post some pictures of the single and double chain drives?
Creo Parametric 2.0 Advanced is actually WF5 in the below link. They must have made a mistake when uploading the manuals.http://www.vertanux1.com/instructional-manuals.html
Liz,You will find a lot of free learning in the attached thread.http://communities.ptc.com/thread/55876
You're welcome. Let me know if I can be of any help with your analysis.
Cherise,There are a lot of links in this post for self-training.http://communities.ptc.com/thread/55876
I think you have to go to Model Setup and uncheck FEM Mode. See the below thread.http://communities.ptc.com/thread/59094?start=0&tstart=0
With the introduction of Creo, the capability to rotate an image by degrees was removed (Figure 1) and replaced with rotation by dragging (Figure 2). The problem with rotation by dragging is that it snaps about every 3 degrees, and the user has lost some control of accuracy. Restore the rotation by degree capability in Creo while keeping the rotation by dragging.Figure 1: WF5 Rotate by Degree InputFigure 2: Rotation by Dragging
As far as I know, you cannot edit the point cloud from an IGES import, because all the points are fixed without any means of editing. To create geometry from the points, you can make curves through points, and then make surfaces from the curves. I looked at the import, and it's a bit rough. One of the problems I have with it is that I cannot see the points unless I select the import feature in the model tree, as shown below.
SPR 2140780 has been corrected in Creo 2.0 M030 and Creo 3.0 F000. Description of problem: "Image placed on surface of part does not rotate smoothly and about spin center in Creo Parametric 2.0."
Thanks Richard.
How do you calculate reactions at the ends of a beam?
....and it was under consideration by R&D in WF5....and how long ago was that?
PTC Support replied and stated that text_height_factor was not supported and not under Quality Control. Their response is attached.
Read this:http://communities.ptc.com/thread/56172
If the model has the same volume and density as the real part, it should be the same.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.