Recently active
Fatigue Advisor, Creo Simulation’s module for fatigue analysis, is optimized to obtain a rapid indication of whether a design is sensitive to fatigue without having to provide the full range of input normally required to solve this type of problem. The solver technology integrated with Creo Simulation’s Fatigue Advisor is nCode International. The physical nature of fatigue was not widely understood during the early days. August Wöhler therefore took a more pragmatic view of fatigue analysis. The method he developed later became known as nominal stress (or S-N) fatigue analysis. This did not differentiate between the Stage I (crack initiation phase) and Stage II (crack growth phase) growth methods and instead related the nominal stress range to the time taken to complete failure.Though S-N analysis is still widely used in test-based fatigue analysis, it has one major drawback for computer aided engineering (CAE) applications. Fatigue initiation is driven by
Armen, I believe you will find the solution to your problem in this previous post. There are several presentations attached in this post on centrifugal loading, and I had basically the same problem you have now. Give this a try, and if you can't figure it out, let us know. https://community.ptc.com/t5/archive2/unreadable-title/td-p/31571
Perhaps Mark Fisher can explain this.
Erik,Try typing in 17GB as shown below and see what you get.
Erick,The memory limit I was refering too was RAM allocation for solver.
Guido,By default, Creo will install English, and that's why you were able to easily switch back to English, because someone had selected German during the install.In my case, while updating to Creo 2.0 M080, I had to select the desired language under Customize for each application, Help Center, Parametric, Simulate, etc. Since I wanted German, German had to be selected, as it will not install by default. If this is not performed during install, you cannot switch from English to German. Figure 1: Selecting German for ParametricFigure 2: Selecting German for Help CenterAfter installation, the language will still be English. To switch to German, open the parametric.psf file with Notepad (location shown in Figure 3).Figure 3: Path To parametric.psf Enter:ENV=LANG=germanSave the file then exit.Figure 4: Opened .psf File
Paul,For this particular problem, you can add a 1mm round to all the corners, as shown below, place a measure in the highly stressed area, and plot a 1% convergence. The attached file has no errors in the run and converges nicely. This is just one example how you fix the run errors in the design. You don't have to use as many elements as I did, but I just wanted to show you that you can get the model to converge in the highly stress regions and in the run summary file.
Mats,That is true, but the study with fewer elements ran 5x faster on our PC. Analysis with 1390 elements: 273.36 sec Analysis with 8937 elements: 1369.01 sec
Add the functionality to save .zip files from Creo Simulate.
Paul, I've attached a Creo 2 file, and from this model I ran two studies to show you that generating a lot of elements will not give you a better solution in the region of interest. The below screenshot shows two studies. The top result used the default autogem settings (1390 elements), and the bottom result has some autogem controls in place (8937 elements). Both studies were set to 1% convergence. Also, some of the rounds could be suppressed or not even created to decreased the number of elements.
Steve,I tested it on my Creo 2 with Adobe XI also, and I didn't encounter any problems, as shown below. Try making a simple model in a clean directory, as I did, and then try to print to pdf from a drawing. I don't know if that will help, but you should be able to print to pdf. I have Creo 2.0 M180.
Community,How do I make cross-hairs over circles in Creo Drawings? I'm currently using Creo Paramteric 3.0 M060.
Allow dashed lines under the hidden view display to be seen as dashed lines on the screen, not just for exporting to pdf.
But PTC doesn't define the performance problems. I questioned PTC on that under the Product Idea, and they're not responding.
Interesting.
Nice work.
Have you tried to mirror features as you go just to test it from time-to-time or are you going to wait until half of the model is completed?
It does it when you export to PDF.
Martin,I can change the center lines to black under options before printing.
I know, but I was trying to find a way to do it without sketching. Thanks.
The cross-hair will have solid black lines after exporting to PDF.
Thanks.
Community,Can the hidden lines in the below image be shown as dashed lines? Thanks in advance.
Frank,I know how to show the axis under model annotation, as shown below, but I want to know if Creo can make solid black cross-hairs on the drawing as shown in my inital post (without having to sketch them in). AutoCAD and Microstation will "pop" these in for you, and I can't find where Creo has this functionality. The image at the bottom is from a post, and it appears that the cross-hairs are solid, and this is in PTC.
Martin,Thanks for the post. How can I get them to be solid and black on the drawing before printing?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.