Recently active
Currently (as of Creo Parametric 2.0) when adding a Command to the Quick Access Toolbar the Command is only available in the module where the Command was added.For example, when in the Part Design module customize the Quick Access Toolbar and add the 'Activate' command. Switch to the Assembly Design module and notice how the 'Activate' command is not listed in the Quick Access Toolbar. The user must then customize the Quick Access Toolbar again to add the new same 'Activate' command.It would nice if functionality could be introduced where users can define if the Command is to be made available Globally across all Quick Access Toolbars, versus select modules.
PTC, please provide a WYSIWYG editor for easier creation of Resource files for GUIs! Using a text editor isn't really modern.
In 3D and when I use the measurement tool, several times the result of the measure, puts itself below the window of measure, sometimes except the window Creo.In simple thing to realize: this measure must be always visible.It is very irritating to move windows all the time.
Currently the way how Mechanica reports measure results for shells is not correct. When the user measures for example a stress at a point of a shell element (compressed sheet), the measure can actually report results from the opposite side of the plate. The following example shows a shell model with two measures. One on each side at the same location of the plate. Since the plate is loaded with a combination of bending and tension, the stresses on top and bottom are different. In that particular example the stress on the top side is -1 MPa and on the bottom side the stress is 3 MPa. Figure 1 Example of measures on a compressed sheet Figure 2 Definition of point measure Based on the definition of the measure (at point) you would think that Mechanica will report the stress of the plate on that side where the user has created the point. Unfortunately that is not true. The measure will report the maximum absolute stress of both sides of the compressed plate. For that particular example the
As in Drawing and Mecanism, to have a Mechanica tree.
The current functionality of Pro/E to find internal volume is abyssmal. Users are forced to subtract parts and assemblies from a solid and find the resulting volume. The process breaks down even further if the components themselves have internal volumes, such as tanks or tubes within a larger assembly. For very large assemblies, the process does not work at all because of limitations of the shrinkwrap utility.Please add a function to find the internal volume of a body using a more elegant solution, such as ray tracing with multiple light sources, acoustic waves, etc.
In proe and creo, only one Show All Views is style mode only.This functionality is High-frequency used in product design, can review and modify models effectively. However this great functionality is available in NX and Solidworks
Enable to Split the screen to four views: top view, front view, right view andd isometric/trimetric/user defined view
Make double-click action possible on features in model tree to show dimensions.Features are not always visible for double-clicking modification in graphic environment (hidden curves for example).Right mouse button action is not as straight forward as double-clicking.
Vote for the "Sketched Point" tool to be added to Creo (useful tool brought back from WildFire4).With Creo5, we have lost the functionality of sketching datum points directly and independently from "Sketch" tool.- Sketched Points are displayed as “curves” in model tree. This is not didactic.- The datum points created with Sketched Geometry Points are hidden with the default Curve def_layer- Creo5 Sketched Point disappears when layer curve is hidden.
Currently in Creo 4.0 circular refences are shown as existent in the Notification Center, but if you click on it, it is not shown in detail. Not in every case in the message log line is observed by the user and they are not really sure how and where to open the complete information given in the .crc file. There are so much actions to avoid additional clicks in a release update, but these clicks are very strange. Please implement the full .crc file content in the notification center and allow to jump to the real effected components not on the main assembly.
We use ModelCheck and GateKeeper to maintain a level of control over models being used in Creo and Windchill and verify CAD standards.Today in Creo 2 and 3 you cannot directly run ModelCheck on bulk items. All items should be able to be ModelChecked.
Creo Parametric does not allow more than 31 characters for its filename (prt, asm) now.I want to use much more characters because I want to add some information like a project name, a person name, updated date and so on.So I want PTC to support more than 31 characters for the filename in Creo.Thanks,
There is a requirement from the Business to have an option in Creo Parametric which can generate the X,Y and Z (Length,Width, Height)values of the model from the Bounding Box. Many users will use this for packaging studies. Please have this option in Creo Parametric 6.0.3.0 version
whilst busy working on fairly complicated model and using in-context modelling. CREO is good enough to inform you when you have mistakenly created a circular reference but gives no idea as to where it is. it may only be 1 constraint that is causing it. it would be great and very time saving if CREO could, as well point out the circular ref , point to the feature or constraint that is cause it. this could be done with the yellow triangle in the tree and a note in the info area.
Currently, if you want to see the milling area, it's necessary to play path trajectory, display tool kerf, analyze toolpath and go back to edit definition mode.Idea: Add possibility to display "Tool Kerf" (trace of tool along toolpath) in Edit Definition Mode of Pro/NC sequences without playing toolpath.
In trajectory milling : it's possible to specify an axis in "Plunge" tool motion.It's impossible to specify an axis in "Retract" tool motion.
International companies would have a benefit, if the language of the user interface could be changed during a running session.
Model Check could be very useful but its setting is very hard, not user friendly. It has not upgraded since Wildfire 2, I think.
It should be very useful to have in the 3D RMB (floating) menu the option "Through All Symmetric"
hello,to manage the sheetmetal drawing with a Template, I use simplified rep to have in first folio the bend part, and in folio 2 the unbend part.but with this configuration, I must use the simplified representation in an assemby. to do that, I place the part, replace it by the ben simplified rep, and assemble it.It would be usefull to be able to modify a default simp rep excluding the flat feature to manage by default the bend part, and have a "unbend rep simp" used in the drawing.
Indeed, our use case is to perform a Widnchill classified search for Catalog components (eg WTparts in Libraries classified with PartLinks), and once the WTpart is found, browse its related 3D model and bring into the active assembly in one operation by drag and drop instead of doing many steps such ascopy the cad model filename in Windchill page the go in Creo assembly, create assemble feature, and in the Open Model window paste the file nameopen in Creo with right click and then assemble from objects in sessions (provided you can remember which object among the hundreds of objects in memory you have previously selected)add to WS and then assemble from objects in WS (provided you can remember which object among the hundreds of objects in WS you have previously selected)Unfortunately we have found no way for such a drag and drop in the standard PTC Windchill and Creo Parametric integration.As of now, the most efficient seems to copy and paste the file name, but it is not welcome by use
we have many model variants with different connection contours, that we put into the model by inheritance. If these contours differ so much, that it makes no sense to put it in a family table, it would be useful, when we were able to replace the reference model by a "replacement" assembly (Sorry, I don't know the English name of this AAX feature)
The old "Turbo Pattern" process of creating a surface, solidifying it, then patterning that has been consolidated into what is now called "Geometry Patterns". Unfortunately this is only available in solid modeling, not the sheet metal module. The fact is that sheet metal perforation for EMI and airflow for thermals is a common design in many fields.The fact that you can't create vent holes in sheet metal with the geometry pattern process is a huge miss. It also shows the inconsistency within Creo between modules. Please enable the ability to create geometry patterns in sheet metal parts similar to how it is done in solid mode.
Now, this is going to be controversial because "it's always been like that", and I can see that suddenly reversing the behaviour could confuse established users.But... how many times have you done Save As (sorry, Save A Copy) then proceeded to start carving up the model - before realising that you're changing the old model, not the copy you've just created?If reversing the behaviour is a bad idea, how about either introducing Save As in addition to Save A Copy; or adding a dialogue box to ask which file you want to keep open?Similarly, Backup shouldn't leave you working in the backup copy IMO - if I'm creating a backup it's because I want to keep a record of where I was, not start changing it.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.