Recently active
Chamfers: when you measure a O X O and / or a O1 X O2 chamfer, the result dosen't correspond to the shown dimension.The default "Offset Surfaces" type of value is not useful for construction.Please add a config.pro option to choose "Tangent Distance" by default.PTC suggests defining a mapkey to not use the default “Offset Surfaces”: article CS53776« Advanced Chamfer Topics » explains how these chamfers are defined.
The attached document describes the case, which basically means that part annotations were using dimensions from a separate sketch (created as a separate feature in the model tree), and that makes it impossible to hide that sketch on the drawing without the also the geometric tolerances made as annotation also gets to be hidden (The annotation geometric tolerance uses a size dimension from the sketch).Creo 2 M130 is used.At the part the sketch feature can easily be hidden and the geometric annotation tolerance still shown, it is only at the drawing the issue appears (Hide/Unhide and all kinds of layers have been tested.)There is another PTC support case about a similar thing from May 2015, also in Creo 2. The two suggested workarounds are really NO GOD for me, and really no options for what I try to achieve.See attached document. (Unfortunately no part and drawing can be shared) BRMartin
Now for hide component of subassembly in top assembly you have to use layers or simplified representation. If you try to hide component of subassembly by button "hide" (RMB) in the tree of top assembly it will hide component in subassembly and it is so inconveniently. It will be cool to have two buttons - "hide in assembly level" and just "hide" (in subassembly level).
Sometimes you need to split subassembly in top assembly to separate parts with (or without) saving references to each other, but now it impossible to do in Creo. You can do opposite - make a subassembly in top assembly (combine separate parts). It will be cool to have button (RMB) - "Split subassembly" in top assembly level.
i would like to be able to use an exploded state of a sub-assembly in an upper assembly. rather than to re-explode the sub-assembly in the upper assembly. some times we have one drawing for multiple subs and show all of them in the exploded state. i looked on forums and tech support and this is not available now.
I would like that the global interference check had a threshold for it to display only interferences that have a volume of interference larger than a number I could specify. This way I do not get too many tiny interferences. I do not care for thread interferences of bolts and screws.
Now ribbon color in Creo 3.0 is white and very washy. In the end of the work day you feel that your eyes are absolutely tired and blinded. Creo 3.0 must to have possibility to change ribbon color. I think It is so easy to add in program, please give it to us!
Add the ability to rename a parameter.This is something that I consistently wish for please.
Many of the mechanism products and other modules can output an .mpg file.When you insert these into a Powerpoint then file has to be linked into a folder.I mostly convert the .mpg files into an animated gif using open source command line tools.This could be a really valuable addition as a pull down menu.
Creo Simulate doesn't set contact on assembly automaticly.It's very hard to set contact between part and part on assembly.I want automatic setting contact on assembly.
Creating a balloon note with 2 lines of text is impossible at the moment. When you enter multiple lines of text for the balloon note, Creo Parametric encloses each line within a balloon, stacking them horizontally or vertically next to each other, depending upon whether you choose Horizontal or Vertical on the NOTE TYPES menu. The size of these related balloons is equal to the largest one necessary to enclose the longest text.For a custom balloon symbol it's possible to add a second line; however, it does not scale to enclose the text.Product idea:Automatic scaling of the balloon based on the text/line length for a customized balloon and/orAllowing two lines of text in a balloon note
Currently there are third party software alternatives for 3d topology optimization. It would be very nice to have this as part of Creo, or Creo Simulate. Now that 3d print has been incorporated in Creo, it seems even more appropriate to include such a functionality.
Try to make most display styles options configurable and "mixable": it would be great to be able to have, for example, "shading with reflections with edges" like it was in Wildfire 4 or 5 if I remember correctly. Or we could have "shading with edges" with or without visible tangent edges (now you can have it only in hidden lines). We could have the ability to add ambient occlusion to a shaded with edges view but without reflection etc. As a plus it would be great to be able to define custom "display style" and recall them from the usual drop down menu
I would like to be able to replace a component in an assembly with an assembly that includes that component and have all the references update to the same references on the component. I need this functionality because we put many parts in kits. Sometimes the kit numbers need to show on the Creo Parametric drawing. If I am creating a new kit subassembly, I can use Move to new subassembly to easily create a subassembly from the component and add the additional part for the kit. Sometimes, someone else makes the kit so then I need I need to use replace to change out the component with the subassembly. In this case, I need to manually reroute all the references from the component to the component as it exists in the subassembly. Creo should be smart enough to know that the same part is being used in the subassembly and remap all references to it.
If I open up the relations dialog box and click on a feature and then a dimension it puts the dimension variable at the end of the end of the last line. This doesn't make any sense. The last line is usually a complete relation. For the specific case of immediately after opening the relations dialog box, the curser should jump to a new line.Instead of this:It should be this:
The FMX is great technology, we can modify or rebuild geometry arbitrary.We hope the FMX technology can be add into Sheetmetal mode,it will be a great improve,I think.At the same time,with regard to such as stp igs and so on,if work under the Sheetmetal mode,I hope can add some commands to discern and transform into Sheetmetal mode(see the picture)Thanks!
An interface tool for JT Extension for PTC Creo Elements/Direct Modeling (18.1) , to read and write structure, geometry and visualization information contained within JT files, while retaining associativity
Imagine that you have a complex part including many features,some times you need to create shell for some features,as we know it,s difficult to do.so my opinion is that we can create a closed quits,next using shell command,that well be nice!
Creo- Mechanism needs to have the feasibility to do dynamics study for Chain.1. Mechanism should be real case. 1. Assembly constraint between Bush and Pin should be as it is real scenario (i.e.: Pin should have 2 linear DOF and 1 rotation DOF) within the boundary(bush hole). 2. Chain should travel with respect to 3D contact only. Not in the defined curve path.
Where creating a simplified rep I find I am always adding a description column, this is sticky while in session but I need to add this every session. I have created a mapkey but the ability to save these changes or call up a different treetool would be better. You have given us the ability to save the treetool.txt but not given us the ability to do anything with it.
Creo's workspace (with Windchill) is missing one helpfull feature, the ability to create subfolders.E.G. if you have multiple big assemblies in your workspace, you can have thousands of single parts mixed in the same workspace.If you need to find single parts then, it is very time consuming and confusing to scroll down the list.But if you could create subfolders, you could deal assemblies in separate folders and it is easier to manage order in workspace. Just like working in Creo offline mode and saving files to computers hdd.Please, rather than just marking a negative point, leave a few words feedback, why do you think this is a bad idea. I appreciate all comments and ideas, if you know better ways to handle large workspaces. In this idea, you are still free to use the current (folderless) way, you won't lose anything.
Hi everybody!Now when you work with notes in drawings (Creo 2.0 and 3.0) you don't have possibility to add markers or numbering automatically in text. Of course you can add it manually but it so inconvenient.I think it will be cool if PTC add automatically markers and numbering into notes like in Microsoft Word (when you pushed enter -> next marker or next number).
Now in drawing in Creo Parametric you can't make an associative link to balloon into the note (if you don't have Windchill, but even if you have Windchill it is so inconvinient to do). It will be cool when you work with notes in drawing just click on the component of assembly (from the tree, for example) and have his number of balloon into your text..
Now when you changing arrow style it doesn't work dynamicly (you don't have a privew). At the picture you can see that cursor of my mouse on the circle style of arrow but style is still square. I think it will be better if you see preview of your choise of style.
Now so hard to use advanced framework extension of Creo Parametric in Russia because it don't have Russian language.I don't know the business directions of PTC in Russia but it will be so cool to use it in Russian language. I hope PTC will add it so soon.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.