Recently active
Mauro,The problem with using a boundary blend in the corner is that there is discontinuity in the reflection analysis (see below image circled in red). I had already tried that method, but I didn't like the results. And yes, there were additional sketches in the model from experiments, I just left them in there. Thanks for the reply.
Shashank,The model is attached for educational purposes, as it may not be exactly what you're looking for; and it was created in Creo Paramteric 3.0 (M040) Commercial Version.
Shashank,See if this is what you're looking for (image below). I can post this model tomorrow.
Sachin, See if this is what you're trying to implement: . - PTC Community
I'm not sure where to post this so I'm starting with this private group hoping that Pierre Maraninchi or Ryan Kelley can direct this to the right person.Searching within the PTC hosted Creo online help frequently returns little to no helpful information, even when the information is clearly exists right in the documentation. Here is today's example:A user asked me, what is this command:Naturally, the first thing I did was search the support knowledge base. Nothing. (Technically this is understandable for now since the knowledge base does not yet index all of the product documentation. I sure wish it did...)Next I searched the Creo 3 Online Help (the subject of this discussion). Still nothing.Next I tried searching Google itself. Sure enough, it exists, but not on any English sites.I then manually copied the URL and replaced "French" with "usasii" and it took me to the correct page where the phrase is clearly listed.http://help.ptc.com/creo_hc/creo3
This document is intended to be a guide to understand the part chain inventory roll up (good) process and fulfillment logic within a part chain.
This document is intended to be a guide to understand various part kit cases (valid and invalid/ unsupported) in Servigistics.
Smart, Connected Applications Maximize Agricultural Business PerformanceThingWorx Platform gives OnFarm Go-to-Market Capabilities
An introduction to what Inventory optimization means in Service Parts business. What are different approaches to calculate inventory stocking levels and comparisons between different methodologies.
IntroductionThis document covers the steps involved with upgrading an Service Knowledge and Diagnostics (SKD) installation to the latest release. PTC can only provide the general process for upgrading SKD. The customer upgrade team must add the details of the deployment specific configurations and customizations. This guide is a starting point for creating the site specific upgrade instructions.The official PTC documentation should always be checked for release specific instructions before starting an upgrade. The latest documentation guides can be found at ptc.com: https://support.ptc.com/appserver/cs/doc/refdoc.jspUpgrade InstructionsExisting installations of PTC Servigistics Knowledge and Diagnostics can be upgraded to a new release.Use these instructions to upgrade your installation of PTC Servigistics Knowledge and Diagnostics:1. Do the following to back up the existing installation. a. Use Servigistics KM Studio to back up the repo
PTC is pleased to announce the release of PTC Service Suite 4.2. This version of PTC Service Suite contains many new features to increase user productivity. This document describes the product updates included in the 4.2 product release.
Key forecasting enhancements in SPM 11.0 and 11.1
Entering Planned Order Dates through GetHostData can cause unexpected errors when leaving some of the Planned Dates empty. Order Plan tracks four Planned Dates: 1) Planned Order Date, 2) Planned Ship Date, 3) Planned Receive Date, and 4) Planned Available Date. These dates must have values in the sequence given. Order Date first, Available Date last.The lead time between each of these dates can be established through parameters and attributes.If only one of the planned dates is provided when entering orders through GetHostData, GetHostData will calculate the other three dates, provided the lead times are established.GetHostData errors can occur when:1) Lead time is missing between Order and Ship, Ship and Receive, or Receive and Available.2) More than one Planned Date is provided but not all four dates.When all four Planned Dates are provided, GetHostData creates (or updates) the order and sets the Planned Dates based on the information in the download table. If there is only one Plann
Are you stating that you're having problems getting the two parts to attached during the automesh? What do you mean by, "getting the two parts to attach"?
Lucas,Did you try simple hand calculations on the upper center hole for shear tear-out and bearing?
Richard,GEA (Geometric Element Analysis) is the acronym RASNA used to define the adaptivity method where the fidelity of the model is increased by raising the polynomial order and the element is mapped to the geometry. It's still the same with AutoGEM (GEM means Geometric Element Mapping). Creo Simulate doesn't use the GEA acronym, that I know of. That's a bold statement to say, "this is not FEA". What are the two techniques in the rejection? P vs H?In principle, any problem which can be solved by the h-version can be solved by the p-version and, conversely, any problem which can be solved by the p-version can be solved by the h-version. There are large differences in convergence rates, however. For example, it was demonstrated in one well-documented plane elastic model problem that to achieve one percent relative error in energy norm (which is similar to the root-mean-square measure of error in stress), approximately 1000 degrees of freedom were needed wi
In principle, any problem which can be solved by the h-version can be solved by the p-version and, conversely, any problem which can be solved by the p-version can be solved by the h-version. There are large differences in convergence rates, however. For example, it was demonstrated in one well-documented plane elastic model problem that to achieve one percent relative error in energy norm (which is similar to the root-mean-square measure of error in stress), approximately 1000 degrees of freedom were needed with the p-version and properly designed mesh, whereas 10 million degrees of freedom would have been required with the h-version, utilizing 8-noded quadrilaterals and uniform mesh refinement. For details, refer to p.190 in Szabo and Babuska, Finite Element Analysis (1991). There are other important areas where the p-version has clear and substantial advantages: adhesively bonded joints (where very large aspect ratios are required), structural plates and shells, fracture mechanics,
See attached. Notify your co-workers. Note - will change on a ~daily basis.
The IoT Value Roadmap (v.2.0) is a guide to help organizations create value in a smart, connected world. Key IoT use cases (some including AR) from hundreds of customer interactions are defined and linked to their business impact in the form of value driver and metrics. Start your connected journey here.NOTES:This version includes the KTM Motorcycle AR Welcome Experience. Requires the Vuforia View phone app. Use with: IoT Use Case ebook
Thanks Denis.
Erik,Are your contact analyses failing due to contact with finite friction? That's what I'm asking.
Ketan,Can you upload a sketch of how you would like your drawing to appear with coordinates? You can identify a coordinate in any drawing with a note. Since you're dealing with a 2D planar drawing, there is an X and Y to every point relative to the csys. But you want to identify a dimension, not a point in space?
Erik,What do you mean by "I cannot use Creo 3.0 for normal business"? Are you referring to just the finite friction capability?
After deleting an intelligent fastener, it leaves the holes in the plates. These holes were created by the intelligent fastener module while making the fastener. Is there an option to remove the holes when removing the fastener?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.