Recently active
Will Creo Simulate perform the following analyses on a rotor turbine? 1. In order to perform a dynamic frequency, a modal analysis must be performed first. 2. After the modal analysis, spin the model at 96000 rpm for 1 minute at 75 degrees F. 3. View the stresses. Currently, PTC technical support has not been able to answer this, as the case number 11575905 was started on Sept 5, 2013. The online knowledge base has only one example, which doesn't fully address the problem at hand. Any comments/solutions are welcomed.
Dan,I made a comment on your Product Idea, and I voted on it too.
Rajiv,What software version are you using?
I liked your answer anyway, regardless of the post date. Thanks for the input.
Dan,Creo has a function called UDF (User Defined Feature), and I'm going to contact one of the developers for assistance and see if we can get this programmed to do what you want. I submitted a Product Idea for PTC to add Plane By Equation back on 11/7/12, as NX and CATIA have this functionality out-of-the-box. Creo will also do it, but with a UDF, which can be a very powerful tool if you're good at code writing. The sad thing of it all is that PTC is still sitting on my idea, and it's been almost three years. It's something so simple for developers it could have been added between date codes years ago. I'm all for your product idea. I'm always in support of ideas that other software have, but don't be surprised if PTC doesn't even acknowledge it. I've attached my idea for the plane by equation.Creo Parametric 3.0 Plane by Equation Ax + By + Cz + D = 0
There will be an upcoming 10.7.8 release of the Field Service Mobile client for iOS and Android. This release will only have minor changes related to the support of iOS and a fix for unsupported versions of Android. Once the official release of iOS9 is available in mid September , PTC will begin our final verification testing so that we can release 10.7.8 to the app stores in the upcoming weeks. For this release, we will post both Android and iOS versions to their respective app stores at the same time. This will result in Android users receiving the updates up to two weeks earlier than iOS users. Below is a quick summary of what to expect in 10.7.8.iOS - The testing of the 10.7.x version on the latest builds of the iOS 9 beta has not identified any issues within the mobile app. If the final verification testing with the official iOS9 release goes well, there may be no changes required in the mobile app to support this iOS update. However, any
Wir freuen uns, Ihnen die spannenden Keynotes der PTC LiveWorx Europe 2015 zu verkünden!Corporate Update zur PTC Firmenstrategie von James E.Heppelmann, PTC Präsident und CEO Celebrity Keynote mitDavid Coulthard, ehemaliger Formel 1-Rennfahrer, BBC TV Formel 1-Moderator und Berate für Red Bull Racing und Scuderia Toro RossoMark Gallagher, Senior Executive im Management von Jordan Grand Prix, Red Bull Racing und CosworthPTC Technologie Vision vonRob Gremley, Executive Vice President, Technology Platforms, PTCBrian Shepherd, Executive Vice President, Enterprise Segments, PTCBrian Thompson, Senior Vice President, CAD Segment, PTCCelebrity Keynote mit Prof. Gunter Dueck, Philosoph, Autor, Kolumnist, Mathematiker, Management Experte und Mitglied von "World 2.0"Sichern Sie sich noch heute Ihren Platz bei der PTC LiveWorx Europe. Lassen Sie sich von den Keynotes inspirieren, profitieren Sie von zahlreichen Breakout-Sessions rund um die Themen CAD, PLM, ALM, SLM und IoT sowie dem Trainingsange
Luis,I've attached an image of a meshed body in an assembly, but Mats has already demonstrated this, but you want to hide all the other components.
Luis,I think I understand that you're concerned about viewing meshed bodies in the pre-processing phase, not the post-processing. The previous link that I provided was only for post-processing, as you can see each meshed body and even cut those meshed bodies to view stress results or whatever results you have pre-determined.I think Mats gave you the best explaination. This is on my list of Product Ideas, to have the same meshing capabilities in Creo Simulate as they do in StressCheck. StressCheck will do exactly what you're asking for, because each body in StressCheck has it's own independent mesh record before even assigning material properties. You just select the desired mesh record (or elements sets as they call it) and that's what you will see in the GUI, the desired meshed body.However, if you're concerned about the meshed body being invalid, Creo will give you a report (diagnostic tool) that will show you the troubled elements, if any, during the automesh
When applying cosmetic lines for exploded views, you can only selet two references. In the below image, there are three colored lines drawn over the existing cosmetic lines, as it took three cosmetic lines to show the fastener path through two components. This means the collector for each thread had to be launched three seperate times. To improve the speed in creating cosmetic lines through multiple components in an assembly, add the capability to collect more than two references in the same Cosmetic Offset Line window.
Hi Luis, You can plot any component from an assembly, as detailed in the attached post: Can you hide components of an assembly in a Creo S... - PTC Community Welcome to the forum.
I noticed several post in the community that I made several years ago, and they are showing up only 7 days ago.
How Smart Connected Products Are Transforming Companies | PTCIn their upcoming October 2015 Harvard Business Review article, How Smart, Connected Products Are Transforming Companies, co-authors Michael Porter of the Harvard Business School and Jim Heppelmann, president and CEO of PTC, examine how companies need to transform their organizations to capture the opportunity created by smart, connected products.Smart, connected products and the data they generate are transforming traditional business functions, sometimes radically:Product Development: Establish and promote seven new design principlesMarketing and Sales: Convert the way to sell, go to market and manage customers relationshipsAfter Service Support: Shift from reactive to predictive and increasingly remote serviceHow do companies transform their organizations to capture the IoT opportunity?Increasing collaboration and integration between IT and Product DevelopmentEstablishing three new and distinct functional units: Unified Da
You can place points on a rectangular surface by ratio or by length.
Mark,I was able to resolve this on my own, but I'll give you credit for helping out. I worked on this for an hour yesterday, and I always got the same error. So I went home and started over again after deleting all the offset lines. I made all the fasteners and nuts on the same axis, and made offset lines that are inline with the fasteners, but this sort of defeats the purpose of "offset".
When I make offset lines going from the bolt to the hole in the skin, it works fine. But when I try to make the final offset line from the nut to the hole in the skin, the line always winds up in the middle of the other line as noted below. Does anyone know how to fix this? Thanks in advance.
Participants Linda LamotteVincent BourdinFred ValenteThomas OschmannJuergen Daus (Organizer/Host) Agenda - Proposal/s:Mission definition of AB (Responsibilities of the AB). Setting the expectations by Mgmt.MissionsheetSet the communication frame (TSE/TSAM) how to connect to themtechn. communication, interpersonal communication - what else?GER/FRA, @home - localized, in-/out of scopeSet the communication frame (Management) - and how to connect to them.Interaction with the US AB - Alignment (Invitation for a call/discussion)Meeting with US ea. 3/6 month, for exampleA EU Sharepoint* or some other kind of promotional Portal / website to be created.Fred already established a basic AB website.Content to be discussed during local AB meeting.In case of re-elections of the AB, provide detailes information on how to grow into the AB role.Definition of the election of a new ABMission definition [done]Brainstorming:The result can be seen in our Mission Statemen
Open ItemsCategoryAssigned ToRecorded onCurrent StatusNext stepsTime frameAttach-mentStatusDue DateDoneShared NA/EU TSE calendarProposal SylviaTHOMay 5Discussed May 27/Jun25/Jul16 and until further notice - re-opened, discussed and accepted for EU TSEA EU TSAM TSE calendar is appreciated, when available in THOT or a "automated" Outlook-cal.Thomas in discussion with IT.Mid-term-workingJUL 16EU WGM Standup MeetingsQuestion from MgmtTHO/FVAMay 5SUM is ok in general, but too many participants in meeting. Often used as a podium for discussion on life cases.Thomas wanted to separate case discussions and "whats news".THO/FVA will present a proposal in next AB meeting.mid-term-ongoingAug-13EU AB Workshop meetingInternal discussionABJul16decidedAB Workshop planned for Sep. 08&09,Fred&Vincent to travel to MUC.Linda will set up local meeting environment (room, catering).Fred&Vincent to request travel approval (tool)Jürgen to create draft agenda and align with the boardClosed ItemsCate
HIGH LEVEL MISSION STATEMENT-------------------------------------------------------------------------------------------------------------------------------------------------------------The purpose of the EU TS Advisory Board is to maintain a culture of dare, innovation and empowerment at all levels of the European delivery teams, aiming at improving customer experience and our work environment. The board is representative of the European Delivery Teams (ALM, Core, Premium/TechLeads, SLM, TPG, TSAM/PRM/CSM) Their mission as representatives of the Premium Technical Support Team i"Do you have concerns/ideas related to your work environment? Could it affect as well your colleagues?Then here we are, the EU TS Advisory Board."-------------------------------------------------------------------------------------------------------------------------------------------------------------ListenThe Advisory Board is here to listen to the European Delivery Teams , regarding any issue or idea abo
There must be something wrong with dating of posts. I know I posted that a couple of years ago.
Glad to see there is this exchange area created within PTC Community
Thanks Erik. That was a really old post that I had resolved and forgot to update it.
Neuer Name, neue Inhalte?Nicht ganz. Vieles, was unsere Anwender aus den Vorjahren kennen und schätzen, wird auch in diesem Jahr bei der PTC LiveWorx in Stuttgart zu finden sein. Natürlich auch die beliebten kostenlosen Schulungseinheiten der PTC University. Die Anmeldungen für die PTC Creo und PTC Windchill-Kurse gehen täglich bei uns ein und wir freuen uns über die gute Resonanz.Nun haben wir jedoch auch 2 neue Formate im Angebot. Beide sind kostenpflichtig, allerdings zu einem speziellen Konferenzpreis.Die PTC University Master Class: "Einführung in Model-Based Definition mit PTC Creo Parametric"Diese ganztägige Schulung richtet sich an fortgeschrittene Anwender, die gezielt in einer kleinen Gruppe ein Thema erarbeiten möchtenDie Master Class "MBD" wird in deutscher Sprache gehaltenKosten pro Person / Tag: EUR 350,-Weitere Infos erhalten Sie hier, und durch Ausfüllen des Formulars können Sie ein unverbindliches Angebot anfordern. Unsere Trainingsberater rufen Sie zurückTermin: Monta
PTC University Precision LMS 8.0.1 was released on August 24, 2015.This release includes a new self-registration feature and an new unified Login page. There are a series of detailed demonstration videos available on PTC University Learning Exchange.What’s new in PTC University Precision LMS 8.0:Self-RegistrationCreate license activation codes and allocate license seatsDelete, disable, and export activation codesDisplay info and details about activation codesSelf-register with an activation codeUnified Login PageSingle page to log onto Precision LMS: eLearning, class guides, self-registrationIf you have any questions or feedback about this release, please don’t hesitate to comment below or email PTC University Support.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.