Recently active
1. Describe the ProblemCurrently the only way to create "Full Rounds" in the Found feature is if we select a pair of edge references. There is a specific user case where we want to create a full round, but with the current Creo methology it is not possible, not even in the latest Creo version (12.4), and this use case happens quite frequently. When we are designing "cooling" lines for parts in the molds industry, we frequently need "holes" whose bottom is a full round instead of planar or forming a "V" shape. The hole command only allows this two options, "Flat" and "Drilled" (tiipical 118º or 120º cone tip). Sometimes we use the "extrude" command to make "holes", and afterwards we need to make wither a full chamfer, or a full round at the flat bottom of the exreuded "hole". To increase productivity and avoid design erros or regeneration failures whe we change diameter of the holes, we need a way to apply full rounds to the flat bottom of the holes, but Creo currently do
Please include detailed documentation such as screenshots, images or video.1. What product and version are you running?Creo Illustrate 10.02. What is the problem?Currently, Creo Explode Lines import as static Datum Curves rather than native objects. This lack of associativity forces manual rework as any change to the sBOM structure causes these curves to vanish, requiring illustrators to redraw every single path from scratch. We need the capability to convert Creo Parametric data into native Creo Illustrate objects that persist through sBOM or positional updates.3. Are you using a workaround? If yes, please describe it.No, I have already contacted PTC Support and no usefull workaround was provided. Currently, we have to redraw all the explode lines of our products after they are imported into Creo Illustrate.4. What is the use case for your organization? Describe how your idea would work in context or how it would apply to a practical situation.We frequently restructure the sBOM to cre
Hello, I’m having an issue in Creo Drawing:When I select a dimension and go to the Tolerance tab, all options (General, Shaft, Hole) are greyed out/uneditable.I have already enabled tolerances in the model properties.I have already retrieved ISO tolerance tables.The dimension is not a reference or driven dimension.Curiously, some drawings work fine, and their Tolerance tab is fully editable.Has anyone encountered this? How can I enable the Tolerance tab to edit tolerances in drawing dimensions?Thank you!
Hello @ all, Creo Elements/direct should support new Step242 Data Exchange. It completes Model Based Definition and it´s very useful to Exchange Date with other CAD Systems.
1. Describe your environment: What is your industry? What is your role in your organization? Describe your stakeholders. Metal stamping company, we develope metal stamping tooling. 2. What version of Creo Parametric are you currently running?7.0.43. Describe the problem you are trying to solve. Please include detailed documentation such as screenshots, images or video.Scale bodies and quilts, should be enhanced. Scale the whole body or quilt, as a scale factor for all axis, or special scale factors for each axis.4. What is the use case for your organization?Create some deformation, for bodies and quilts5. What business value would your suggestion represent for your organization?
im a begginer and im having trouble making a cooling vent on a revolved surface ... i could just sketch the all the shape on one quarter ( mirror after ) then project it and maybe use punch or something like that to get the slots , but it seems like too much work and not really the smart thing to do , is there any other way i could do this ? not only the patterining it self is a problem but also having the pattern not cross the 120 diamter circle and the smaller circle ( the one with the hole ) , the modle comes from an exam question at the uni im learining at ... im using creo 10.9 thanks a lot
Hi everyone, I'm doing this creo excercise and amquite confused seeing how the tutorial video handled this part of the drawing.tia!link to the video I'm referencing: https://www.youtube.com/watch?v=ssI7dJEkdys
I am using Creo Parametric Release 10.0 and Datecode10.0.5.0Creo 1.0.5.0 failed to register windchill 13.01 server.When registering a WIndchill Server in the File Server Management it will not connect after selecting check. User and Password are correct. URL is correct.Here are the errors that I facedWIndchill Authentication Failed
How to modify this symbol? I want to change value of 2 PL to .01
Hello,I have a cross section of a radial pump rotor with radiuses which I want to annotate the standard way with arrow and ''R8'' written for radius of 8 mm. I can do that to other curvatures, but not to to the surfaces made by feature ''round'' that are made on vane endings. I tried with ''show model annotations'' but there I can find these annotations being scattered elswhere to unwanted positions. Can not move them to cross section by ''edit attachment''. Whenever I click the curve that represents cross section of a round to insert ''dimension'' nothing happens- no dimension is written and no arrow shown. Same happens for any other similarly created rounds in this cross section. Despite round being defined as round of 8 mm, I can not measure it with ''measure'' tool. What is the way to annotate such rounds on cross sections while keeping them dependant on radius defined in ''round'' feature? Best regards!
Hello All, I’m trying to simulate torque applied to a ¼” hexagonal driver to a reduced A/F set screw. I have set the simulation up but getting very high stresses in the results. My question is does applying the ‘total load at point’ effectively divide the moment load by 6 in this case, the point created is at the centre of the hex? Due to the stress reported I suspect I may have to divide the torque value by 6 manually when setting the load up?
Hello all! I am reverse engineering radial pump rotor. I want to achieve a constant radius between pump vane and the ''casing'' - as if it is a ''round'', that fails if I try generating because of complex edge and surfaces. So basically I am asking for help/advice/past experience with how to make complex ''round'' feature on spiral-like intersection of two curved surfaces. I did it before with ''solidify'' of created quilts -but they were uneven and hard to change if I wanted different and constant radius along the intersection. Thank you!
Hi everyone,I’m working in Windchill with parts and drawings stored in my workspace. I’ve generated the drawing PDFs, and now I’d like to link all related information—such as design calculations, supporting documents, and relevant email correspondence—to the specific part in Windchill.The goal is to have a complete design history or data package for each part, similar to how it’s managed in Teamcenter, where all associated files and communication are traceable and connected to the part.What is the best way to achieve this in Windchill?Is there a recommended workflow or structure to ensure everything stays linked and easily accessible later?Any guidance or best practices would be greatly appreciated!Thanks,
Hello, Right now a supplier is using Creo elements direct modeling latest version and they create annotations drawing files and send .bd2 files to us. I wanted to ask if there was a way for us to open it or convert it without having to turn it into a neutral file? We tried step file but my issue is when it comes to Creo Parametric the models are broken? Is there no direct way to address this? Thank you.
Hi everyone,I’m working with Creo 11 and trying to use the APIs ProDrawingViewDetailCreate and ProDrawingViewPartialVisibleAreaGet, both of which require a ref_point of type ProSelection. I’m facing consistent “bad input” errors and would appreciate any guidance from someone who has successfully implemented these.Here’s what I’ve tried so far:Method 1: Programmatic datum point creationCreated a datum point → SuccessUsed ProPointInit → SuccessConverted using ProPointToGeomitem and Modelitem APIs → SuccessAttempted ProSelectionAlloc() → Failed to return a valid ProSelectionMethod 2: Manual selection approachCreated a datum pointSelected the point using ProSelection → SuccessPassed this selection to ProDrawingViewDetailCreate & ProDrawingViewPartialVisibleAreaGet → Both failed with “bad inputs”Method 3: Drawing entity approachCreated a point in the drawing using ProDtlEntityCreateUsed ProSelectionAlloc() → SuccessPassed it to ProDrawingViewDetailCreate & ProDrawingViewPartialVisib
Dear expertsI'm just frustrated about very primitive exercise in Creo Simulate 12. See the sketch below. In creo there is an assembly contains 2 composite parts, in real glued together. The cored composite board (composites 1) is bonded on composite frame L profile (composite 2). The target is to see how the rigidity of L profile affects the modal frequencies of board.Only composite quilts are supported in Simulate, it means the virtually gap is observed, the layup guilts are not in touch, bonded connection is not supported in this case. I have tested a lot of procedures, rigid link, spot weld...etc., but only bonded interface is closest to real surface - surface bonding.Another test I have made, in assembly the 3rd part - glue was created, the thickness was a gap, but there is a material interference - glue + laminate in real. Does anybody have an idea how to fix that? What is the correct connection feature between two composite parts, or generally between two shells?Thx a l
Autonumbering in Creo Parametric is not consistently implemented. In some places Creo displays <auto generated name> and doesn't consume a number from Windchill until the action is completed. In other places Creo consumes a number immediately, as soon as the related dialog is opened, before any actions have been completed. (Just opening the dialog and closing it will consume a number.) Please change this so <auto generated> is displayed everywhere and no number is consumed from the database until it's actually needed (the action is completed.) Good: Everything works exactly as desired when creating a brand new file in Creo. No number is pulled from the database until the object has actually been created. Bad: This falls apart everywhere else. All of these other actions will pull a number from the database as soon as the dialog is opened: Save As from Creo Assembly - Create New Object Assembly - Replace (even
I have an assembly with two components. Every components has a simplified rep with the same name; UDSR where one feature is excluded. When I create a simplified rep in my assembly, I can select the User Defined Simplified Rep, pick UDSR, from each component. Works perfect. Now I want to create a rule-based simrep, where every component is loaded with the user defined simrep "udsr" in it.In the rule editor, I am on the Status Tab, selecting Display. Is it possible to search for a user defined simrep with a particular name?
We have three variations of Notes: 1.Generic2.Harness3.Fabrication and AssemblyHow to let system give me option to use what I want on drawing in NOTES: ?SEE IMAGE
Hello everyone, I am working with Creo Parametric 12.4.2.0 and I want to export a .dxf file from a drawing, using:File > Save as > Export > DXF I usually use a sketch or a solid from a .prt file and place it in my drawing to do so. This works perfectly fine in Creo 3 and 6. My problem is, that whatever is contained on my drawing, gets turned into a image, when exporting it via Creo12. So if I open the .dxf file in another software, I do not have single splines or curves anymore, I have one big, very blurry, image, as seen on top here: What have I tried:using a solid part as a baseusing a sketch as a basetrying different dxf versionsdeleting layers for the export checking unit is the same between .prt and .drw export without drawing boarderexport with drawing boarder What I found out:creating the sketch directly in the drawing file returns a clean assembly of lines - but I do not want to re-draw my designs from the .prt. So this is
Hi all,Creo+ Version - 13.1.0.1-001Windchill+ Version - 12.1.2.17 I'm trying to map attributes from Windchill+ to our start parts and then drawing templates to populate our change block. I feel like I'm probably not the first to try this and imagine there's a solution out there I just can't find. One major issue I face is that due to being on a Windchill+ system, I don't have the ability to change attributes through Type & Attribute Management without moving through PTC. If that is the only way to achieve my goal I will, but just need to know if that's my best bet. The attributes I would like to map would be :Change Notice NumberCA II DescriptionResolution DateCreated By If anyone has some information I would be grateful! Attached is image of an ECN with red outlines for the desired information to be mapped. Thanks,
Hi, I'm new to the forum. I've been using the free version of Creo Elements and I have about five files in pk2 format, one of which is important. I now have a Creo Parametric license, but I can't import pk2 files. How can I transfer the files from one software to the other? Can someone convert them for me so I can use them in Creo Parametric? Thank you very much for your help.
1. Describe the ProblemTo assign materials to our parts in Creo Parametric, we use the Ansys GRANTA Gateway that fills Creo materials attributes in the model. This Gateway is connected through the GRANTA Database where we gather all our organisation materials information. We are starting to use the Creo Composite Design module and in this feature, we can't use materials from the Granta Gateway. 2. Are you using a workaround?We are assigning composite materials through the Creo Parametric materials feature in the Composite feature (see screenshot attached). Therefore we use the PTC Composite materials library and not our Composite materials from our databases in Granta. 3. What is the use case for your organization?We are starting to use the composite module for some real use cases in our organisation and we would like to use the composite materials that are in our Granta databases.4. What impact does this problem currently have on your organization?We can't use th
I am using Creo Parametric Release 12.4 and Datecode12.4.2.0Hello,in 2D drawing, I'm not longer able to fix the symbols to the dimension, but now just on the viewI remember in the old relase (9 - 10) It was possibleIs the a configuration needed or other to have the possibility?Thank's in advance
I am using Creo Parametric Release 11.0 and Datecode11.0.1.0How can we change the sequence of the ply when using trim option
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.