Recently active
Hello fellow engineers, Recently I updated from Creo 7.0 to Creo 10.0. I am in the middle of a project so maybe it wasn't a good idea. When re-running a buckling analysis that used to return a BLF of about 2.5 in Creo 7.0, now I get values of about 0.5! Has anyone noticed this pattern? I believe the new 10.0 version is overconservative, as I have done hand-calculations to verify the buckling mode and the plates are nowhere close to buckle. I believe the solver must have been updated. The model in question corresponds to a crane with a telescopic boom, where the contact pads (usually solids to allow for contact definition, non-linear analysis) are replaced by a beams (linear analysis).
Hi,One of my customer is facing issue when he tries to open the Creo elements direct modeling. The error says as LISP error, CAD Angle is not allowed. Kindly help me with a resolution.ThanksNaresh
Good morning community, I have a general question about how Simulate reports rigid modes when "with rigid mode search" is checked. I created a simple part with a surface constraint and released 1 DOF (in the Z-direction). I would expect Simulate to report at least one rigid mode that would show the assembly translating along the Z-direction. The animation does show this but it doesn't say it is a rigid mode. Wondering why that is? Is there a frequency threshold before Simulate reports the mode as rigid? I released 2 DOF of freedom (in Y and Z) and then it does report rigid modes. However, when I animate it, there is some rotation of the assembly in the first mode which I would expect only translation. I attached my assembly file.
I am having issues with importing a term table .csv file into Creo schematics 7 and unsure where to look or correct on the issue. The table seems to work fine with 1467 entries and seems to start having issues of not loading and locking up schematics when additional entries are added beyond that. I am also uncertain if any blank cells have to have an entry of UNSET or if they can be left blank.Is there a limitation on the number of SET columns that can be created. Any advice or suggestions would be helpful.Thank you,Scott
I am developing a UDF for screw threads and ports and need some support understanding whether a certain implementation is possible and how to manage references to make it happen. Insofar, I have defined UDFs with a coordinate system that every other feature ultimately points to and placed these UDFs using that coordinate system and one placed in the model, or the on-surface coordinate system option. My understanding is that the basest feature(s) appearing in any UDF will be what all the other features ultimately reference. Ultimately, we would like these UDFs to be placed with reference to an axis the screw goes along and the face the screw extends from. However, I'm struggling to figure out if it's possible to manage references in such a way that those are the reference prompts. I have been experimenting for a while and can't arrange datums in a way that accomplishes this. More broadly, I've been having some trouble defining UDFs to point to anything B
Please include detailed documentation such as screenshots, images or video.1. What product and version are you running?Creo 9.0.5.02. What is the problem?Currently Creo users cannot copy Multiple geometry in single attempt.3. Are you using a workaround? If yes, please describe it.yes.. we can copy one geometry at one time. Which is time consuming4. What is the use case for your organization? Describe how your idea would work in context or how it would apply to a practical situation.Improving Productivity5. What impact does this problem currently have on your organization? (Number of users affected, hours of lost productivity, etc.)Aprox..150 users
I can't seem to delete a cable break after placing it. I don't see the "X" that is supposed to represent the cable break in the flat model. Anyone experienced this issue?The only way I have been able to successfully delete it is to delete the entire cable segment.
Good afternoon, I am new to using GD&T advisor, so far as a tool i think it potentially has a lot of benefits. However i am at a stage where i have completed all the GD&T definitions, and now want to add some traditional dimensions, eg. linear dimensions from datums to plane surfaces. When i try it says 'no applicable reference'. I am unsure how i can have traditional dimensions along side GD&T
I am using Creo Parametric 10. I am encountering a similar issue to what is described here: (1) Replace by unrelated component and asm0001 already... - PTC Community. From that, I am able to delete the "asm0001.asm" from my workspace and that allows me to use replace by unrelated component. However, when I try to upload the "replacement" part to Windchill, I get the error "Assembly - asm0001.asm is not unique". I checked the Reference Viewer in the part, and asm0001.asm is not listed. Where else can I check to break the reference? The part file is a family table, if that matters.
after installation of creo 11 student version the screen became black and no entities are highlited when drawn. My graphic card is RTX3050. windows 11
1. Describe the ProblemWe are not able to edit the end location of the cables when using auto routing.The exported XML files from Creoschematics tend to gray out the options, which makes it hard to edit to change end locations.When using manual routing we can edit the locations.So, requesting to check if it’s a bug, or if it is how cabling works, or if this can be provided as an option. 2. Are you using a workaround?There is no workaround.3. What is the use case for your organization?We are using "Auto Routing for Peumatic Design, Here, we need an option to add a Location point.4. What impact does this problem currently have on your organization?Around 200 Users
1. Describe the Problem In the Creo Drawing Place, the MARKING Symbol pointing to "Hidden surface (according to standard)", When pointing to the Hidden Surface in the drawing, the Leader Line must be in "Dashed Line" 2. Are you using a workaround?Yes, place the symbol without a leader line, draw a line between the hidden surface and the symbol, and then change the line type to "Dashed." This is a time-consuming process.3. What is the use case for your organization?In the Drawing, the Hidden Surface must be shown with a Dashed Line Type.4. What impact does this problem currently have on your organization?More than 2000 Users.
I am looking for a feature in Creo that allows you to select faces of two features and determine the relationship between them. For example, in SolidWorks, if you select two flat surfaces, it will show whether they are parallel or perpendicular in the bottom right corner or the analysis window. Similarly, if you select two circles, it will indicate if they are concentric or offset. Is there a feature in Creo that provides similar functionality or something close to it? Thank you.
Hi I'm trying to make an asynchronous app that help automate some processes.is it possible to iterate through all parts/sub assemblies in an assembly and add all components with a specific file name (test.prt for example) and add them to the selection buffer? I want the user to have the option to right click and hide/exclude/delete the selected components. any example of how to add components to selection buffer will be appreciated. thanks
I can define the thread hole format in the .hol file after edit CALLOUT_FORMAT line.but i can't define the countersink hole format based on this way, anyone can tell me how to define that? another problem is how to hide the zero after the decimal point?
I could use some help understanding the differences between User Defined Features and Family Tables, working in Creo 10, how you choose which to use when trying to standardize/parameterize a particular component or feature, and why you would use a User Defined Feature that contains (or otherwise references) a Family Table or vice versa. Here is my current understanding of the differences:User Defined FeaturesCreated from features in a part file, may or may not maintain references to it (subordinate/standalone)Creates a .gph fileUsed with a series of defined prompts that relate to feature parameters (dimensions etc) and placement in the model using itInstances as a body or a modification to a bodyFamily TablesBased around a generic ancestor part fileCreates additional part files as you create instancesUsed by assembling instances of the relevant part fileInstances as a part
Description:In Creo Parametric, ordinate dimensions created within sketches are not available for reuse as annotation elements in Model-Based Definition (MBD). This limitation forces users to recreate dimensions outside the sketch, which introduces a risk of tolerance mismatches between the sketch and the annotation. This can lead to serious production errors, especially in high-precision environments.Proposal:Allow ordinate dimensions from sketches to be reused directly as MBD annotations, similar to how driving dimensions from features are handled. This would improve consistency, reduce redundancy, and enhance safety in the design-to-manufacturing workflow.Use Case:Mechanical product development in automation systems, where sketch-based ordinate dimensions are critical for layout and manufacturing accuracy. It is also highly beneficial for complex parts, where ordinate dimensioning improves readability and reduces interpretation errors.
Hi, when I put the subassembly, wich parts are constrained to the straight lines in the picture below, in an assembly, I would like to modify the green circled sketch dimension from a value of 1160 mm to 1400 mm with 20 mm pitch dimensions: how can I do it without relations?Is there a method that allow this procedure with flexible dimension? Thank you, Michele Baril
I am pretty new to Creo Parametric and running into an issue where updating a part requires large amount of re-definition in assembly. I'm designing an adaptor between a t-slot beam and a table, the adaptor is applied 20 times over. Every time I make a change to the adaptor's sketch or thickness the assembly requires me to redo all the definitions of parts around all the adaptors. How should I avoid this?
I have an assembly that needs multiple configurations. In one configuration component A is assembled to component B. In another configuration, A is assembled to component C and B doesn't exist or is suppressed.I think using a Family Table and Constraint sets would be a great solution. In the first FT instance I have a Constraint Set that constrains A to B and in a second instance, I have another Constraint Set that assembles A to C. However, the problem is that when I suppress B in the second instance, A becomes suppressed as well. I'm assuming this is because the Constraint Set that is used in the first instance makes A a child of B. Is there any workaround for this? Is there any discussion about having disabled Constraint Sets severing or negating parent/child relationships? It seems to me that would make sense and open more flexibility when using Creo assemblies. Currently using Creo 11
I can't get a texture to save in the company appearance.dmt with the texture file saved. Is that because the save_texture_with_model does what it says and saves the texture with the CAD file? Anyone have any luck saving a texture file in the appearance.dmt for use as a company standard? Hoping I am just missing something easy here. I tried putting the texture file (.jpg) in the same folder as the appearance file but that doesn't seem to be working. When I open up the appearance.dmt with a text editor the there is a color_map line that references my jpg filename so it is saved in that file. Does the full path need to be in there?
1. Describe the ProblemWe spend a lot of time selecting the same settings within the Creo due to the fact they revert back to the default when the feature is closed. In most, if not all cases the default is not used which forces us to re-pick all settings for the next use of that feature. If all settings, you modify were to be retained until you change them or at the least until the file is closed, we would be able to reuse that feature as intended. This would eliminate many clicks throughout the day. This is a common approach with other software and actually is sometimes the case within Creo (Round dimension is saved until changed). One example would be the steps below to create a hole for an insert. Once the hole tool is closed these settings are reverted back to default. Often, we reuse the size or one close with most settings the same. 1. Select hole button,2. Select standard,3. Select countersink,4. Select hole type using hole template,5. Select s
Good day to anyone, first time posting here! I've been having a very simple issue, but as I am accumulating an increasingly large amount of files and need to navigate multiple folders, it has become quite a hassle that Creo's 'File>Open' Menu only allows for opening a single .prt file at once. Unfortunately, as the files in question are only somewhat related, they are not part of an assembly and as such cannot be opened together using the 'Open Subgroup' option.In many other programs, I could use Control-click to select multiple files individually or Shift-click on two files to select all files inbetween, then have all selected files opened in their own respective windows after clicking the 'Open' button. Is there a hidden option to select that would allow me to open multiple files at once? Or could I somehow replace the file mangement system with a somewhat more user-friendly one? Thanks for taking the time to read my post. Any assistance in the matter would be very
I am using Creo Parametric Release 11.0 and Datecode11.0.2.0Need sample code for Pro/Toolkit C-API to form the following element tree...// PRO_E_SURF_CHAIN_CMPND// |-- PRO_E_SURF_CHAIN_REF_SURFS// |-- PRO_E_SURF_CHAIN_SURF// |-- PRO_E_SURF_CHAIN_REF
I am using Creo Simulate Release 11 and Datecode11.0.1.0We have created fnf file in creo simulate using FEA mode, then we loaded the fnf in creo simulate UI using external file with temp on required node. During loading we set reference temp as 22, after seeing in previews it shows 0 as ref temp.We ran multiple thermostructure analysis, but it shows its not taking 22 as ref temp. & showing worst resultAlso not loading controlled mesh in Creo simulateCreo version: 11.0.1.0
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.