Recently active
Is it possible to download old PTC software during Sustained Support? Unable to find old datecodes of expired PTC products on Software Download web page. Is it possible to download installation files for products which are expired and no longer part of Standard Support policy?
1. Describe the Problem There is currently no ModelCHECK check for determining view-related layer status in drawings. drawing dependent layer statusview-related layer status 2. Are you using a workaround?Some users activate the layer object selection in drawings so that the colored view frames are displayed. The color of these frames can at least visually indicate whether any view has a view-related layer status set.3. What is the use case for your organization?In principle, it's only very rarely necessary to set a view-related layer status, but sometimes there is no way around it. If you aren't the creator of a drawing that you are currently editing, you often don't notice whether view-related layer status are available. And in my company there are several hundred Creo users, which means that it's very common to have to change drawings from other people or to use them as templates for new drawings. It would be very helpful if ModelCHECK could report view-related layer status.4.
Hi Creo Team, While performing Dynamic Time analysis should the mass normalization parameter sim_massnorm_modes in Config.pro be set to 'Yes' or does the Dynamic Time analysis automatically sets the parameter to 'Yes' when running. Regards,GS
I am using Creo Parametric Release 6.0 and Datecode6.0.6.0问题:如何在3D模型中创建与屏幕平齐并带有引线的注释使用代码示例:第9行错误 Translated by the community team using Microsoft Translator Problem: How do I create a note in a 3D model that is flush with the screen and has a leaderExample code used: Line 9 error ProNote note;status = ProSolidNoteCreate(mdl, NULL, pTextArray, &note);ProNoteAttach noteAttach = nullptr;status = ProNoteAttachAlloc(&noteAttach);status = ProAnnotationplaneFlatToScreenCreate((ProSolid)mdl, PRO_B_FALSE, &plane);status = ProNoteAttachPlaneSet(noteAttach, &annoPlane);status = ProNoteAttachFreeSet(noteAttach,note_pos[0], note_pos[1], note_pos[2]);status = ProNoteAttachAddend(noteAttach, selSurfaces[0], PRO_NOTE_ATT_NONE);status = ProNotePlacementSet(&note, noteAttach);--------// return PRO_TK_BAD_CONTEXT-----------status = ProNoteAttachRelease(&noteAttach);status = ProAnnotationShow((ProAnnotation*)&note, NULL, NULL);status = ProSolidRegenerate((ProSolid)mdl, P
1. Describe the ProblemDescription:When creating a coordinate system in Creo, the software currently allows users to select three planes that are not perfectly perpendicular to one another. This behavior can cause significant issues during the manufacturing process. In our workflow, we frequently use product surfaces directly as references for coordinate systems. However, some of these surfaces are only approximately perpendicular rather than exactly 90 degrees. As a result, this leads to errors during NC programming and machining.Proposed Improvement:We would like to propose that Creo include an additional validation or option when defining a coordinate system:Automatically verify that the three selected planes are mutually orthogonal.If they are not, the system should either prevent the creation of the coordinate system or display a clear warning to alert the user.Benefit:This enhancement would help users avoid potential machining errors, improve manufacturing accuracy, and ensure co
I have been trying to find an answer to this question but nothing I have tried so far works. I have an issue where I can not pull the Windchill browser window to the front above all of the other Creo windows. I'm currently using Creo 7.0.8 and this is happening to all users who are currently running Windows 11 (but now Windows 10). There doesn't seem to be any way at all to move it to the front so we have to resort to moving all Creo windows to one monitor and the Windchill browser to another monitor. I suspect that this has something to do with the Windows 11 window manager but even the settings that appear to fix other applications do not fix this issue in Creo. Anyone have an idea what I can try?
Hi,I am trying to implement ProMdlReadonlyIgnore with reference to article CS398373, as I am unable to upload parameters while it is in Checkin state. Untill Creo 7.0.11 I was able to do it, but same action in Creo 10.0.5 is demanding me a checkout. By referring article CS398373 I figured we have to use ProMdlReadonlyIgnore(I suppose not as a custom API) but PTC provided. I do not see any document in Creo Parametric TOOLKIT API Wizard .Can I get some help here.
Vers. 10.0.5.0Creo program has stopped using the config options i've had before, specifically inverted zoom shown in picture. I am unsure which is correct for the zoom option i want (Yes or no) however i have tried changing the config file to both options and it has not changed zoom direction and uses the default scroll wheel down = zoom in & scroll wheel up = zoom out.The only notable difference i've done recently is closed the program improperly by closing the pc but this has not changed the config files for me before. Any advice is very appreciated!Solution:Using the link provided and testing what config.pro was being loaded, it turned out to be start up/working directory. Reselecting the working directory with the config.pro solved the problem.
I'm trying to move the Ebom of one of the component, since the option is not highlighted it is taking me a lot of time to moving it manually. It usually never happen. Kindly help me to identify a what was the problemI'm using version 11, have full professional license
Is there an event that occurs when you click on the top item in a CreoUI table?
1. Describe your environment: What is your industry? What is your role in your organization? Describe your stakeholders.Electro Mechanical company. I'm the Windchill responsible and using Creo as mechanical engineer.We just migrated from Solid Edge to Creo2. What version of Creo Parametric are you currently running?7.0.2.03. Describe the problem you are trying to solve. Please include detailed documentation such as screenshots, images or video.As described above we migrated our organization from SolidEdge to Creo and missing certain "basic" functions which were available there.One of the features we are missing is the "Quick view cube" which was available there. A simple cube in any corner, rotating with the displayed model. When clicking on the cube, the view oriented as selected, so in above example it would then orient to the Front view.4. What is the use case for your organization?Especially in bigger assemblies you are quickly lost how you are looking right now at the m
Hi, hope someone could help me how to set up config.pro file or any other way I could sole my issue with Creo interface.My first problem is how to setup Layer tab width on creo startup or when open new work file , ( as every time minimizes for every new part file ) ( see attached image )Second problem I need help with is how to setup line thickness? I would need a less thick selected line, and more thick general lines in 3D model , as this lines are so thin and barely visible on 4K monitors ( see attached )Thank you in advance! Stefan
Hello, I have applied an appearance to a model for carbon steel. I added the appearance by highlighting the whole part, then selecting the desired appearance. Where the issue comes into play is if you modify the part in any way, it will change the cut/intersected surfaces back to the default generic/grey appearance while it needs to be the new carbon steel appearance. Is there some sort of setting to fix this? Please see example below.
Hi!Recently we had a problem with updating views on drawing regarding AFX profils. The views do not reflect the changes made in the 3D. We are forced to manually update all the views for each drawing. Since we have hundreds of drawings per project, this takes an enormous amount of time. And normally, it used to work perfectly fine before. For the past few weeks, it hasn’t been working anymore. The variable auto_regen_views is set to ‘yes’.Has anyone else encountered this issue recently?Thanks for your help.
I'm using Creo 7.0.2.0 and working on implementing Model-Based Definition (MBD) at my company. Are there any specific config.pro or detail options that should be set or adjusted to better support MBD workflows?
We are new to MBD. How do we create the MBD format? Can we use the 2D format? Please share any link and youtube or videos.
Hello,When I make a drawing of a part, we are making it two pages as the second one is same for all including general information. I have a question. Can I make a .frm file and make a drawing with that format to have 2 pages? I do have .frm file for the first page for general title block and another .frm file for second page to insert after manually creating second page at the drawing. What I need create a two page .frm file and when I call it at the beginning it will create desired two page drawing without need of creating second page afterwards.Please ask if it is not clear for you. I will give my best to explain it better according to your questions.Thank you.
I am using Creo Parametric Release 10.0 and Datecode10.0.8.0How create parameters with accentuation using Model Check?Here are the errors that I facedI'd like to create parameters via model check, but it's absolutely essential that the parameters have accents.Here's an example:ASM_PARAMETER DENOMINAÇÃO STR EQ PDMPRT_PARAMETER DENOMINAÇÃO STR EQ PDMDRW_PARAMETER DENOMINAÇÃO STR EQ PDM
Please let me know if there is a good method for creating a winding model when creating a conductor model.Using a helical sweep allows for the creation of a winding with a consistent thickness, but since the coil height is 18mm and the wall thickness is 12.5mm, bending the model created with the helical sweep will cause interference with the coil. If you have a good method, please let me know.Coil SpecificationsOuter Diameter: φ50mmInner Diameter: φ25mmThickness: 18mmWinding SpecificationsWire Diameter: φ2mmNumber of Turns: 13 turnsWinding Arrangement: Wrap around the coil at 115° intervals, with 3 wraps.Gap Between Each Turn: 5°(Calculation: 115° * 3 + 5° * 3 = 360°)ConditionsThe distance between the winding wire and the coil is not constant, resulting in a zigzag shape in cross-section.(Some winding wires will be closer to the coil while others will be farther away.)The winding wires do not overlap.
Creo View Web 12.1 Launch Introducing Creo View Web: Seamless Visualization, Anywhere We’re thrilled to announce the launch of Creo View Web, a major milestone in making visualization more accessible and collaborative across the enterprise. What’s new today: MVP with limited scope - for now Browser-based access to 3D content—no heavy installs required Faster collaboration with teams across locations and devices Streamlined workflows integrated with Windchill for easy access Looking ahead:This is just the beginning. Future updates will bring 2D drawing support, advanced measurement and markup tools, and deeper integration with PTC’s digital thread to empower smarter decisions and accelerate innovation. Start exploring Creo View Web today and experience the future of visualization—simpler, faster, and everywhere you need it. Compatibility: Creo View Web is currently compatible with Windchill 13.1.2.0 Future CPS releases for Windchill 13.0.2 & 12.1
1. Describe the ProblemIn some cases Creo will automatically "flip" an annotation to the other side of it's leader, if a symbol is associated to the annotation the symbol will no longer appear to be located correctly in relation to the annotation. PTC says this works as designed currently. So the request is to have the associated symbol "flip" when the parent annotation flips so that the symbol maintains it's relative location to the annotation. The attached video illustrates the issue very well. It's worth noting that fixing this manually is fairly easy in the example shown where it is a discreet model, but there really is no fix for family table models.2. Are you using a workaround?Reposition the symbol when there is a discreet model. However if it is a family table instance there is really no way to fix this other then having unique annotation sets for each family table instance.3. What is the use case for your organization?This occurs with many annotated family table models whi
Building a decent sized harness that will have a few places where things get spliced, found this video which give me some information on a way to do it...https://www.youtube.com/watch?v=n1Ff4-zHkbA Few things I'd like to know is one is this the best way to add splices to a harness? Would there be a way to do it without adding another physical part to the mix? I have not verified this but doing it in this way would create a new wire number (W-1,W-2 etc) for each new wire that comes out of the splice which would show up as individual wires on a to from table in a drawing. Would there be another method that would call out all those wires as one wire number but still allow multiple gauges? If this is the only way then I get it Creo being Creo. I just find it hard to believe that there isn't a way to splice wires without adding another solid body to the harness assembly and just doing it right in the harness menu.
Hello, I am using Notebooks, Relations, and pro program to configure top level General Assemblies. The problem is, I keep getting the following error when regenerating one of our top level assemblies (blurred out some of the numbers): WARNING: More than one common interchange group found.More than one common interchange. Attempting to replace with xxxxxxxx_INT.Pro/Program replace of component xxxxxxxxxxxx (M94) failed in Assembly xxxxxxxxx.Aborting regeneration due to failures executing Pro/Program. The notebook relations to drive parameters are similar to what you see below Starter_name & Starter_Number are parameters. Starter_Number is the part number in windchill 11.0 commonspace. pro/program example is shown below The issue is that we have a new interchange assembly that is set up correctly to swap these starters. For some reason, Creo wants to use an older interchange that is not set up correctly, but has one of the models inside it. Is
I need often to insert BOM Table in the image (for example as a note), I need to edit BOM Table to insert component attributes as mass or material and BOM Ballon with name of component.
Need to be able to include a Parts List or sBOM within a Figure such that the Published Output can "stand on it's own". API's for Web that enable a dynamic Parts List that is displayed with a Figure for Web do not help when needing to generate paper or paper equivalent output. Also, need to be able to insert the output of Creo Illustrate into an Arbortext Editor (could be a specialization of DITA within the technical Information Application) such that a Parts List and Image "go together". Ideally the above API would be built into a specialized XML Schema so that when PTC Products such as Creo Illustrate and Arbortext Editor are used together they not only function together but really work well together.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.