Recently active
Add ability for the Repeat command to include assigning all placement and orientation constraints related to a component that has Mechanism Joint Definitions assigned to it. Currently for example a component that has a cylinder joint defined. When you place the component using the repeat command you are only given the option to select the insert surface for the cylinder. You are not allowed to select or defined the translation reference or rotation reference if it was previously defined in the component you are repeating. This issue exists in Creo 2 and Creo 3 Parameteric Only allows you to select axis alignment Notice translation and orientation are fully defined in component previously placed that the repeat command is being used on below.
When creating a solid hole in Creo (or Pro/ENGINEER) the system will generate a cilinder that consists of two separate halves. Why?The problem is, when exporting to STEP or IGES or whatever format, these holes are also exported as separate halves. When exporting is done in order to import it into a CAM solution other than Creo, this creates a problem.When creating a cilindrical extruded surface, the system generates only 1 surface instead of two. Why then creating 2 halves when extruding as a solid???It would make sense if holes are generated as 1 surface, instead of two.
What if we had the ability to create curves or sketched lines using extrudes as the basis, or convert a solid to just edges. So if you make a standard cube you wouldn't have a solid, or surfaces, but curves for all the edges. The biggest example I have is we make a lot of frames in AFX. To get all the sketches to build the outside of the frame you often have to make multiple planes, multiple sketches just for a simple box. Though if you could make it in extrudes to define the space claim first it would be easier to create. A box is the simplest example, but any extruded shape could be done this way. In theory even spheres could be cut into quads and given sketch lines. If sweeps are also able to do this, here's an example of a model I created as a mock up for a presentation that took way too long to create each edge and each sketch. It was done with 3 sketches and many curves based on points. It could have probably been done with 2 sweeps, not counting the star pattern in the middle. T
I think that PTC should consider adding a config option to fix an issue that bothers most current CREO users.Out of the box, when making components transparent, the edges wind up faded (grayed out). It is not a pleasant thing, especially when dealing with multiple components in an assembly, and many of those components are transparent....image is muddy, and generally unclear.I believe that PTC should either make the default mode to be black edges only (when that option is chosen from the view type icons) - or- At least have a config option that allows black edges to be the default mode, while making surfs transparent.https://www.ptc.com/appserver/cs/view/case.jsp?n=12600723The work-around that is shown below is just too cumbersome, and fairly silly. My neighbor, who uses U.G. gets a good laugh at how ugly Creo's approach to transparent edges are.Nice crisp black lines is what the engineering community wants.......It will be very much appreciated by all once this fix is introduced, (des
It would be a tremendous benefit for all Modeling users with the effort to grow towards PLM with Windchill, if the PTC Creo Elements/Direct Modeling integration to PTC Windchill via the Workgroup Manager would be capable to open "none native CAD files" from the workspace like e.g. the Creo users can do it today. Please see the below comparison of the 2 different File open dialogs. In the PTC Creo Elements/Direct Modeling dialog only Modeling related files can be displayed, where as in the Creo App's Parametric and Direct, the all file types toggle is available. Both screenshots view the same Workspace.View of an Workspace for a PCT Creo Elements/Direct Modeling user:Only the Modeling related files are available.The same Workspace for a Creo Parametric & Direct user, All Files are available:Thank's for voting!
This is currently a limitation because there is no option available which will change the orientation of an underlined reference line in Drafting and / or Annotation. The underline reference line is Always created from left to right. The new option can be useful to create the underline from right to left. LINE
When a partial view spline is needs to be moved a little, you are required to redraw the entire spline. I would like to see the ability to move the points defining the spline for making adjustment to the outline of the view.
It should be possible to assign a cylindrical surface (e.g. bore) with several different colors, using for example a sketch. There should not be created an additional surface and the color should also remain after exporting a step file.
Durch die Nutzung von Children Handling werden vom Anwender Referenzen gezielt zugewiesen, ersetzt oder gelöscht.Dies kann der Anwender mit der Option „Edit References“ für die meisten Feature machen. Wird zum Beispiel eine Datumplane gelöscht, auf die sich auch eine Xsection bezieht, steht die Funktion "Edit References" nicht als Menüpunkt unter dem der rechten Maustastenmenü zur Verfügung.zu diesem Problem ist auch schon ein Case C12607489 gemeldet worden.
Could be useful to show a circular axis for a direction pattern, like axis pattern.
The request is to allow the users to select radial pattern circle as a dimension reference.N.B : This Idea was created after the request of Mr. Alexander Kirillov
I would like to be able to have Text in a 'Box' Frame to be able sit on top of Geometry (as displayed in the images below): --> ThanksBarry
Please add the ability to pause analysis and design studies to allow them to be moved/copy to another faster workstation/computer when the hardware becomes available.This will allow one to take advantage of computational time that has already taken place and not have to start completely over.
We have large assemblies and or large step files that can take several minutes to open. It would be nice to have a progress bar.
Currently the only way to get a view on a non-standard angle and rotated with view arrows is to create a cross section and use a general view or fake in the arrows.An Auxiliary view can get a view at an angle, and add view arrows, but the object cannot be rotated. A projection view can create a perpendicular view can also create these view arrows without the need for a section view.Revolved can perform some of the functionality, but it is essentially the same as the cross section method. The example this came up on was a container with angled sides. The features on these angled sides were perpendicular to the angled face so a projection view would not work well. An auxiliary view works but then the box is tilted. It's also helpful when the object you're detailing has clear orientation such as walkways/stairs/etc. This is in line with ASME Y14.3. This doesn't appear to be in Creo 3 either.
The Show Model Annotations should include a filter for better selections.For example, if you want to show axis of a subpart inside an assembly drawing, you would need to click on the part in order to show up, instead of clicking the view. The view only shows the top-level datums, dimensions, etc. There is an option that specifies top-level or all. However, I think it should be more intuitive to users what they are selecting and what they want to show. For instance, controlling layers can be done by drawing, view, model, etc; where there is a drop-down. Here there is no drop-down. The only selection process that I am aware of is toggling through the mouse selection and clicking models/features in the model tree.
Avoir la possibilité de remplacer un composant flexible dans un assemblage sans avoir à supprimer la flexibilité auparavant.
Half-width Katakana and Katakana have mixed in the menu title.(ModelManager) Please unified either.
On a fill pattern the spacing between pattern member centers applies in all directions. On some types of grids it would be interesting to have some more spacing options, for example X and Y spacing on a square grid.
Our company often creates very detailed drawings (with many dimensions, etc.) of plastic injection molded parts. Later, we may determine that one of these parts requires (threaded or other) metal inserts that will be overmolded with the plastic. In this case, we then make a CREO assembly of the plastic and metal inserts. Note that in real life these parts are not literally assembled. We then want a drawing of this new CREO assembly to have all the details (all the dimensions, etc.) that were originally shown in the part drawing. We no longer need a CREO part drawing of just the plastic part because this plastic part will never exist in reality (without also having the metal inserts). So, it'd be great if, in the original Part Drawing, we could multi-select dimensions then cut-and-paste them into an Assembly Drawing, eventually selecting a specific view, as long as the related assembly contained the same part.
Hi,I want to exclude components in simp. representation based on their storage folders in Windchill ==> I decide to create a simplified representation based on rules When creating the simplified rep. based on rules in Creo Parametric, for exemple a rule that exclude component based on the parameter PTC_WM_LOCATION( attribute=> Expression => string => PTC_WM_LOCATION => égal) ==> the expression value field is limited to 32 caracters ! This is very annoying, as this parameter gives the location of the subfolder in a Windchill Context, i want to take just a portion of the entier expression, when selecting the value of the expression from the drop down menu, it allows the expression to be very long, when typing Anything manually it takes you back to the 32 caracters limitation.I think this limitation is not logical and should be removed.Thanks in advance.
I want the ability to distribute a "saved searchs" to other users. There is thing called search conditions that everyone use. There is no way to distribute now.
"Saved Searches" are arranged in alphabetical order, but I want the ability to specify a direct ordering.
I want to display your name to the top of the list owner.Since frequently use.
When plotting Simulate results in a graph form (such as from a sensitivity study), any re-plotting of the graphs causes format changes to be lost - including such basic things as adjusting the axis limits.Editing the window properties for that graph or even adding a new window both reset the graph to default; and format changes are not kept when saving the results windows (.rwd).Fringe plots have been improved so that the legend is not always reset; now can we have similar improvements in graphs, please?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.