Recently active
I have not seen this before, but since you're using a student version, you might want to post this in academic section.Check the hardware requirements against your PC.
Thanks.
Thanks for the link. I have the HP ZBook 15 G2, and I have the right graphics card and current driver.
TriStar makes a 90-page reference book for Creo 2 that has ISDX within it. You can see it in the attached link. https://www.amazon.com/Creo-2-0-Thiagu-Palaniappan/dp/1934357138/ref=sr_1_fkmr0_2?ie=UTF8&qid=1487261021&sr=8-2-fkmr0&keywords=TriStar+Quick+Reference+Guild
Paul, So far, I have not been able to get Creo 4.0 F000 to install. Details in the attached thread. Creo 4.0 F000 Installation Problems - PTC Community
Ruben,Here is an explanation from Robert Lansdale of Okino Computer Graphics: "What you are experiencing is all part and parcel of the MCAD manufacturer's pulling the wool over your eyes, as the terms I use. PTC, Solidworks and others have a well defined "hack" (which I too have on my IGES exporter) which fools people into thinking that mesh data can be "imported". That's what causes forums around the world to explode with incorrect perceptions towards this process. These are called "proxy graphics" in which their hack allows a mesh model to be viewed but not partake in any modelling operations. ProE/Creo is purely a BREP solids modeller and hence has no understanding nor notion about polygonal data. To edit polygonal data you need to use a very simple modeller such as Rhino, 3ds Max, Maya, SketchUp, etc. and not a high-end and common MCAD modeller."
Erick,By default, Simulate averages the stresses in the elements, unlike Mechanica, where the operator had the option to view averaged or un-averaged stresses to check for continuity. I currently don't know of a way to plot the stress on a single element, like you can in StressCheck. But you can set up pre-defined areas for measure and plot convergence on those areas/regions of interest. This will tell you if you have a singularity in the region of interest, because singularities do not converge.If you are concerned about singularities near constraint edges, you may omit these elements from your measures that are produced in the run summary. It may still show up in your legend, but not in the run summary.Welcome to the forum.
Ruben, You cannot import polygonal mesh data into a BREP solids MCAD modeller. MCAD modellers can only import useable data from other MCAD programs and not from simple mesh modellers or 1985-era OBJ files. Simply put, the polygonal file format has no CAD (NURBS) geometry within it.
Zachary,Yes. The Mathcad folks resolved it for me. I have attached the solution in the link.https://www.ptcusercommunity.com/thread/135231
Does anybody have a 3D bolt pattern analysis already programed in Excel?
That's true for non-linear, just one run per study.
I saw some quick reference cards at my last PTC user conference, and they were produced by a company called TriStar. I did not purchase them, but they were very nice and laminated. I just use the installed Help Center, but I know, that's not a quick reference. I will see them again in April, and maybe I will pick some up.
Try the M280.
Luca,Expand the next link down "Creo Elements/Pro 5.0...", because that is the same as WF5. PTC just changed the name. You can order the disk for M280, as shown below.
Do you have a picture of your requirement?
I would recommend moving your request to the academic section of the community, as shown below. I don't deal with licenses for student versions.
Here's an image of a model using Creo Simulate Lite. You only have three load choices, and thermal is not one of them.
It sounds like you have a licensing problem, not the software itself.
According to the Help Center, it's not for Creo Simulate Lite. It only allows for three types of loads (force, pressure, and gravity), and I attached it in my previous thread. Your screenshot is shown the Lite version.
Not that I know of.
You cannot perform a thermal analysis in Creo Simulate Lite.
For 64-bit Window 7 Ultimate OS, Creo Simulate 3.0 will only allow 16384 MB of physical memory. It is recommended to allow the RAM allocation to be set to 192 GB, the maximum allowed for Windows 7 Ultimate. For example, our HP Z820, Window 7 Ultimate, has 96 GB of physical memory, and we can only use 16.384 GB of it before a design study uses the swap space, slowing the overall run time.The below snippet shows the message from Creo Simulate if you enter more than 16.384 GB. In this example, 32000 MB was entered, and the OS is Windows 7 Ultimate.
Roland has two questions in his original post. My thread was just FYI to show you cannot increase the RAM over the allowed limit.
I already made the comment that it is now available in Creo 4 with ISDX. The product idea was submitted in Nov 2015, way before Creo 4 ever came out. So if end users want G3, they will have to purchase/upgrade to Creo 4 plus have the ISDX.It is highly unlikely that PTC will make if available in Creo 3, now that you can get it with Creo 4.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.