Recently active
I think you can RMB on the dimension and change it under Properties.
You may try using the config.pro optiondefault_dec_placesand set the number of desired decimal places, as shown below.
The attached link from PTC will explain how to set decimal places.https://www.ptc.com/appserver/cs/view/solution.jsp?n=CS139243
Try setting the number of decimal places in sketcher. Go to File>Options>Sketcher and set the number of places as shown below. If that doesn't work, there are some other options. Try this first.
Hi Sylar,You can change the language to Chinese if you selected to install Chinese during setup. Please read my response in the attached link on how to change the language to German. Apply this same process for Chinese, and it will work.http://communities.ptc.com/message/228283
What part of the model shows the 6M psi?
Hi Haris,Since the model is symmetrical, you don't need to sketch all of the model, only half, as shown below. Then you can just mirror the other half. I uploaded the model so you can see how I did it.Figure 1: SketchFigure 2: Complete Model
Yes...you can do it that way....as I have done it that way before. But we want to be able to do it under "Save As" without having to go through all those steps.
Giulio,You can create a mirror component in assembly mode, but after examining your model, you have some features that cannot be mirrored.The idea is to open the model in assembly mode as shown in Figure 1 and create component by mirror.Figure 1In the next step, you will see the mirror options, as shown in Figure 2.Figure 2As you can see in the upper left-hand corner of Figure 3, "Can not mirror some features of this part" is displayed. There's nothing wrong with the software. I think you have some very complex features that WF5 doesn't want to mirror. I even tried this in Creo Parametric 2.0 M100, same problem.Figure 3Sorry, I wasn't able to mirror this with features.
Hi Luca,Yes. There is a way to save annotations in the STEP file. Here's how:1. Add step_export_format to the config.pro file and set the value to ap203_e2 as shown below.When saving as STEP, you will now see the non-geometry selection for annotations. Make sure it's selected.The below model is a STEP with annotations. When trying to import, give it a few minutes to load.
When attempting to open the STEP assembly in another software, does the software have the capability to open STEP assemblies as shown below with Creo? If you don't import it as an assembly, you might not be able to see the components in the model tree.
Thanks Brian. I tried this and it worked great!
Thanks Brian. I have had this problem for a long time and I obtained the registry fix from PTC but never implemented it. I will try adding this to the config.pro file. I like simple resolutions.
No there isn't. I have submitted a Product Idea to add this capability.
Do you want to have ONLY one model that will bend and unbend?
Yes...that answers my question. You're dealing with Windchill, and you want preview pictures of your parts.
You can create a mirrored component in an assembly, keep all the features, and break dependency.
Kamlakar,See if the below equation and images will work for you:Let's use a 3" radius, 90 degree bend and a 0.5" diameter tube with a wall thickness of 0.100". Using the above equation, you will need 4.725" of tubing just to make the bend. And let's say you want the two ends to continue 7" each. The total length of tubing will be (7+ 7+ 4.725)" = 18.725"Figure 1: Unbend DimensionFigure 2: Bend DimensionsFigure 3: Dimension of One EndFigure 4: Material Bend Length for Radius (4.712")This is very close the the 4.725" computed witht the equation. Only 0.013" difference.
The three images that you just posted, what software is it?
Are you looking for displacement in the Y direction for the entire assembly?
Do you have a picture of the project? Creo has flexible hose (rope) modeling capability.
Creo and NX have the same file ext (.prt) but are not compatible.
Hi Tobias,Could you you upload an image (or images) of what you're talking about? What do you mean by CAD document?
Hi Denny,Could you you upload an image of this "problem"?
Hi Mahesh,If I load a part, the additional apps will not display as shown below:But if I load an assembly, they will appear as shown below:Your response was correct, as I need to be in assembly mode to display certain applications. Thanks.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.