Recently active
Guilherme,Here's an explanation on what happens when you enable fix seperation. Notice the deformation plot.
Did it work?
Define "low budget".
I think you will want to solve this with the Beam Tool as shown below:
Here's the article:
If the model is constructed correctly in Creo Parametric, it will mesh in Creo Simulate. A lot of users don't know how to model for the finite element method. I disagree with your conclusion that Creo Simulate is 10% efficient. I've always been able to mesh my models in Creo Simulate that were created in Creo Parametric.
Here's a good article from an engineer who has to work with both products:https://www.google.com/#q=advantages+of+creo+over+solidworks
Tom gave some good advice on how to do this.You can also create your own csys in the STEP import, save a new STEP with the new csys. When you import the new STEP, you can then save it as a .prt file (Creo native). Then you can add it to an assembly file (.asm), and then you can move it anywhere you want. You can add it csys to csys or make it offset distances.
Can you upload the model?
Thanks. That's it.
I'm missing something in this option, as I'm not able to locate radial_pattern_axis_circle. Please look at the image below and see if this is the correct way to add to the detail.dtl file.
Bertil,Glad this worked for you, and welcome to the forum. I had forgotten you were using WF3, so the file is not backwards compatible. At least there was enough information in this discussion so you could replicate the solution.
Hi Bertil,I made the surface based upon the datum points and trimmed it with the green projection curve using another surface, as you stated. The surface is shown below, and it's bit rough. Also, I attached the model. Were you looking for something more smooth?
In general:Import the points with .pts file.Connect the points with curves.Make surface with curves, boundary blend.Can you upload the points in notepad in XYZ columns and attach it to this discussion?
bj p,I took your attached model and applied a symmetry constraint, just to show that symmetry does work in Creo Simulate. Whenever the model and loading has symmetry, use symmetry constraints. This will reduce your run time. I know that you place a rigid link on the bolt, but I removed it just to show the effects of bolt bending using symmetry, and the rigid link can be easily restored. Also, I put a surface region on the bolt up to the surface of the bracket (surface region is 25 mm long), and the load is applied to this surface without going through the bracket hole. Usually when there is a load applied to a bolt, there is bending of the bolt, as you can see in the attached displacement. I attached my model, just in case you want to look at it and run some investigations.Hope this helps.
You've already downloaded Creo View Express 3.0, but I just wanted to post this incase there are some other users that might want to see what it looks like. You can get it for 32-bit or 64-bit. I've used Express and Adobe for viewing, and Express is a much better tool, as shown below.You have the following extensions when saving from Creo Parametric:
Amazing. I will have to try this.
Creo View Express is much better than PDF, and Express is free.
Creo View Express is free, but you cannot view STEP files with it. I think James is looking for a STEP viewer. If his shop just wants to view models, then .pvz files will work just as well as an alternative, and yes, it's free. Good point.
Perhaps I'm not understanding what you're asking, as you can see in the below image, I have a part that is gray with cream surfaces on the cuts. Maybe this is not what you're asking.
Hi Dhiraj,Do you have an image with a description of what you're trying to simulate? This would be very helpful if you could upload a description. Sometimes it depends on the region of interest of data recovery as to where and how to apply constraints. Welcome to the forum.By definition:
Are you talking about a single part, or a part within an assembly?
Are you trying to create the "bulge" that protudes back to the center of the wheel?
Hi James,Creo View MCAD will allow you to view STEP files. Demo link attached:http://www.ptc.com/product/creo/view/mcad
Matt,You can see a full description of each option in the attached pdf, which is in the Help Center, along with all the new enhancements for each new release under What's New.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.