Recently active
Upgrade to Creo Simulate 3.0 F000.
What does the diagnostics file state? Share this file if you can. See attached image.
Are you trying to mesh parts that were made for manufacturing?
That's been a problem for years...not highlighting the "problem" elements.
Thanks for sharing. I was able to import them also.
Yuichi,Creo 3.0 has corrected the max distance problem between two curves. See below image.
Rohit,Let me see if I understand this correctly:Creo 3.0 Date Codes...F000 Import native fileM020 Open native fileM030 Save As native file...for CATIA, Solidworks, NX, Inventor.I was just wondering how many CAD files PTC is going to allow.
I started a new discussion, and I posted a screenshot of all the open/import file extension capabilities. It's in the below thread:http://communities.ptc.com/message/249972#249972
Martin,I downloaded Creo 3.0 and got it up and running last Friday. I was able to import CATIA V4 (.model) files at the part level and the assembly level, as shown below. I was very impressed, and PTC provided this functionality at no extra cost.
Does anyone know where I may obtain the latest config.pro options listing from PTC for Creo Parametric 2.0? I've attached the WF4 options as an example. Thanks in advance.
I ran the model, and I think the reason all of the fasteners are positive for axial force is that the plate is trying to lift off the block at every fastener location. You have a 200kg mass at the top which is offset from the center of the support beam, creating a moment to lift the base plate off the block due to a gravity load. I deformed the assembly at 30% to illustrate this, as shown in the three figures below:Figure 1: Deformed With OverlayFigure 2: Plate Lifting at Each FastenerFigure 3: Plate Lifting, Deformed and Overlay
Okay...and thanks for the info.I'm very curious to see if I can import a ".model" extension from CATIA V4.
I'm downloading it today, and I want to see if it will open CATIA files, as they claim.
Sean,You stated that you cannot share images or the .asm/.prt files, but you could share following files:Run Summary file, ends with .rpt, automatically generated.Study .pas file, automatically generated. You must review this if you're using contact.Diagnostic file, .txt. You have to save this yourself..stt fileThe iteration status for contact analysis is listed in the study .pas file, the .rpt and .stt file do not give this information. Sharing these files will give your audience some insight to your problems. If you're having this much trouble running in Creo Simulate, you will more than likely have problems with ANSYS.See the below images:
What part in this 20 piece assembly is of primary interest?Don't use any AutoGEM settings on quick check. Just use the default settings to reduce the number of elements.What does the diagnostic tool state after a crash?How many components are connected with fasteners? You're using a combination of solid fasteners and fasteners from the fastener tool.Are you using any contacts?It sounds like you have a plate that is bolted to a fixture. Seems like a simple problem.Are you looking at the stress in the plate due to a pressure load?This difficult to work without images.Creo should handle this without crashing.
A ".model" file extension is from CATIA V4, so I don't know if the V5 import will work.
Creo 3.0 Unite Technology will only open assemblies, not at the part level, so I've been told. We have a CATIA translator, and that will open files in Creo, but I'm hoping Creo 3.0 will allow us to work around that.
Can you upload an image or the model?
Creo 3.0 claims that it can open SolidWorks, CATIA, and NX files directly, without the need for additional software.Does this mean it will open the modeling history of these files too?Has anyone seen this demonstrated?
What does the groove cross-section look like?
I went back and watched the attached video presentation by Brian Thompson, and you're right, he only shows Unite Technology opening assemblies. Now I wonder if you can open a component from the assembly (RMB>Open) after the assembly has been opened, the same way it's done in Creo assemblies?http://www.ptc.com/product/creo/new/It will be interesting to see how this new technology really works when it becomes available. For now, it appears that you can open these native formats, but they will still be like neutral files without modeling history.
No problem. That's why we're here...and welcome to the forum.I use Creo 2.0 M110.
Works for me...see image below.
Follow the instructions below......then post the message.
Where or how is the 550-degree C applied on the model?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.