Recently active
David,Welcome to the forum. You want to analyze the structure in the raised position due to a gravity load. Since the region of interest is the frame and not the hook, you could model the hook has a solid, constrain it, and provide the rigid links as required. The below image is a simple 3D concept of a 1g load on a frame using rigid links. Maybe this will meet your needs.
The example was provided by PTC technical support engineer Mark Fahlbeck, case # 12121958. I talked to Mark about this, and how would you be able to get the direction of the shear load based on the WCS. His response was that I would have to calculate it based upon the shear resultant loads (no example provided). He made two plates and put two fasteners through them along with an applied load to get the above output. I haven't tried this myself, so it's still experimental for me too.
Charles,Here is a response from PTC technical support engineering. This will give you xyz resultants for shear loads, and then you will have to figure out the direction. PTC does not have shear direction out-of-the-box."I did not find any official/supported method to achieve this with standard exposed functionality, but I found an environment variable (not documented & not something technical support supports) that might help. Try adding MECH_BOLT_COMP_OUTPUT environment variable (figures out the force components in the bolt) set to TRUE, rerun, and check the PAS file (Checkpoints tab in Run Status window). You will see something along these lines:"Fastener2_shear_force-x (local) -1.386979e-01 Fastener2_shear_force-y (local) -4.986981e+01 Fastener2_shear_force-z (local) -4.984188e+01 Fastener2_shear_force-x (WCS) -4.986981e+01 Fastener2_shear_force-y (WCS) 1.386979e-01 Fastener2_shear_force-z (WCS) -4.984188e+01 Fastener4_shear_force-x (local) -3.724828e-02 Fastener4_shear_force-y
What note properties? I didn't see any properties under note (RMB). See below image.
I probably need to start a new thread on this one.
Read the first line (question) in my problem statement.
The problem is the leader line is removed after I make the note flat to the screen. Setting the config.pro option did not correct this.
Is there way to make the note normal to the screen without breaking the leader?
I made a simple assembly with some exploded lines, saved the model, then re-opened the assembly. The exploded lines are in the model tree, but not on the assembly. How can I fix this?
And the bolts don't re-align with the previous saved assembly.
Are you refering to the advanced fastener tool or using a solid fastener?
I recommend submitting this under Product Idea.
Does Creo 3.0 have the capability to make dash exploded lines?
Okay. I see it now, as I have shown in the below image. Thanks.
Please see the below image. I was wondering if exploded lines can be made in assembly mode. I sketched in a dotted line as an example.
It is a smart move to move from Solidworks, because Solidworks is about to become a thing of the past.
Creo Simulate 3.0 now has the capability to account for the stiffness of the fastener with a preload. The desired preload can be entered without having to make another run to account for the stiffness. The below example shows 100 lbf entered for the preload, and 100 lbf is shown in the run summary after the analysis.
Creo Simulate 3.0 has provided a way to account for stiffness in the fastener when using a preload. When you check account for stiffness, you may enter the desired preload and only one run is required. The images below show where a 100-lbf was entered for the preload, and the axial load was checked in the run summary to be 100-lbf.
If you have made all the load cases with its own unique load set identificaton, this will make the analysis run much longer.If this is not a multi-body contact analysis, I would recommend putting all the loads under one load set. It will greatly decrease your overall run time.Or try running just one load, and see how long it takes.
Are the eight loading conditions under one load set, or do they each have its own load set? You can overwhelm the system by creating too many load sets. Look and see if all of your loads are under one load set. Send a screen shot of your load set model tree.
Did you select "Yes" for interactive diagnostic before running? If so, you can share the diagnostics file without sharing the model, and that may give us some insight. See the below images for clarfication.
I got Creo 3.0 F000 up and running last Friday, and I must say that I'm impressed with the import capability. I imported two CATIA models (.model CATIA V4 and .CATPart CATIA V5) without any complications. I could import parts as well as assemblies. The open/import capability listing is shown below.
You can now download Creo 3.0 at PTC.
What is shown or listed under Geometry Checks?
Why do you have to mesh the housing? You're just trying to analyze the brackets, right? Find the centroid of the transmission and do total mass at a point and beam it to the brackets.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.