Recently active
What do you mean mapped mesh needs "guide lines"?
In WF4, all fasteners used a spring idealization to model the bolt/screw. This type of idealization uses a 6x6 stiffness matrix enabling us to calculate the axial forces only, it did not account for any shear or bending forces (these are not defined in a spring). In Creo 2.0, PTC removed the spring idealization and replaced it with a Thimoshenko beam which uses a 12x12 stiffness matrix. This enabled us to calculate the axial forces as well as shear and bending forces. The results defined in Creo 2.0 are the most accurate, as the underlying idealization for the fastener better represents the condition. Along with the additional forces captured, the increased stiffness matrix provides more accurate results.
It sounds like when Creo 1.0 was introduced, the modeling and sketcher backgrounds are to be the same, according article CS111283. I opened a PTC case to verify this, and I will let you know what I hear from them.
Try running the model with no shells, and no surface regions, as shown below. I just ran a quick check with no poblem using solid elements, but different load. I did add some material to represent a weld. I'm running Creo 3.0, and I didn't account for stiffness for the bolts. Just make your model simple to start with to make sure it will run.
Are you refering to the base where the tube connects to the plate?
Yes. If you check "Account for Stiffness" in the Fastener Definition window, you don't have to make two seperate runs to obtain the desired pre-load.
I recommend that you upgrade to Creo 3.0 so you can account for fastener stiffness. See below image.
The first thing I would like to know is what are you trying to accomplish? What is going to be your data of interest? Do you want fastener loads? Do you want stress recoveries in regions of interest?
What is the purpose of making all these surface regions?
Interesting. I've never had a problem inserting a .jpg file.
Jason,Here some simple instructions (see below image).
Jason,Welcome to the forum. I don't think you have a memory problem. Look at the below image and see if this is what you're trying to do. If it is, I can send you some instructions on how to add it in Creo 2.0 (image is Creo 3.0). It's very simple to do.
Is there existing functionality that will show all the lines as black when the No Hidden function is selected?
Stephen,When you stated to set the color scheme to BLACK ON WHITE. Were you talking about the system colors?
Thanks Stephen. That solved the problem.
Look under the Analysis tab as shown below:
Are you able to share the model and some images of the problem?
Hello Vikrant,Welcome to the forum. The modeling history shows how to make this spiral stair. Suppress all but the first feature and study how it was made. Then unsuppress the next feature, and so on. You will quickly undestand how this was made without having a video. I opened this up in Creo Parametric 3.0, as shown below.
CATIA does not always win over Creo. It is all based upon the determination of need in the acquisition process.
If you're using a solid bolt to connect two plates, you will also need contacts between the bolt and plate holes. I would recommend splitting the bolt shank surface to match the plate holes.Also, Creo 3.0 does now account for fastener stiffness if you're using the advanced fastener tool. So the operator does not have to make two seperate runs. You have to check "Account for Stiffness" in the fastener definition window, as shown below.
I made the below rotor turbine with just solids and surfacing.
Creo Parametric has:1. Surfacing2. Free Form Surfacing3. Free Style SurfacingI had PTC classes in Surfacing and Free Form Surfacing, and I've used Free Style on my own. With these three capabilities, you can create some very complex surfaces.
I recommend moving on to Creo 3.0.
The purpose of my simple analysis was to show that you can remove the constraint off the frame and use a gravity load. I think David had the bottom of the frame constrained. I don't know the region of interest in this problem.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.