Recently active
Kyle,Are you using a student version of Creo?
Go back to my post where I have "Normal" circled in red and read the instructions. Create a new dimension between the center of the circle and the datum plane. This will remove the light blue weak dimension and create a dark blue stong dimension.
Yes...they change colors as shown below...from light blue to dark blue.
It changes the direction of the normal in selected surfaces or quilt.
That is correct, as shown below.
Dale,In Creo, you don't have to make seperate extrusions. I made the below model with just one extrusion.
Sumit,For the first question, I'm showing a model where displacement is in the -Z and the +Z is help in place with a planar constraint. Is this similar to what you're looking for? Simulate does have the capability to restrict movement in only the -Z direction. For the second question, try looking at pre-defined measures for displacement over time in the Z direction, as shown below. I'm not sure if this is what you're looking for. It would be nice if you could load an image and problem description of the project.
You cannot combine load sets if you're running nonlinear contact. You will have to run each load set separately and view the results separately.
Shaun,I think Mark has the answer here, and I'm showing the underformed overlay as blue (below), the color I pre-selected under System Colors.
I don't see how you will be able to stop the heat energy transferring from the plate to the shaft no matter what software you use, as both materials will expand. Interesting problem, and I would like to know how it turns out.
Herb,Can you upload a screenshot of the message? I've never received that message when saving an assembly. Is this happening in Creo Parametric 3.0 (F000)?
Creo 2 file uploaded (first example).
Yong,It may be better if you submit this as a Product Idea, since you're suggesting this capability be added to Creo Parametric.Backgound information on AI (or .ai)Adobe Illustrator Artwork (AI) is a proprietary file format developed by Adobe Systems for representing single-page vector-based drawings in either the EPS or PDF formats. The .ai filename extension is used by Adobe Illustrator. The AI file format was originally a native format called PGF. PDF compatibility is achieved by embedding a complete copy of the PGF data within the saved PDF format file. This format is not related to .pgf using the same name Progressive Graphics Format.Welcom to the forum.
It sounds like you have a student version of Creo 3.0 where the license doesn't support the style function.
Matt,Welcome to the forum. Look at the below image to see what you select to sketch a datum point. Geometry points are the datum points when you're sketching.
PTC has automatic renaming when you select "Generate New Names", but I don't know of a way to increase the number in your example automatically, i.e., 01, 02, 03, etc. I'll look into it.
You can't change this in Creo 2.0, as I stated before. This is a new enhancement in Creo 3.0 for the draft feature. If you need more than 30°, you may have to create it with a different function, not draft.
Viktor,Are you talking about the maximum angle you can put on a draft? If so, Creo 3.0 allows you to make the angle up to 89.9°. Before, you could only make it up to 30°. The below example shows it at 52°. If this is what you're talking about, there isn't a config.pro option to turn this on in previous versions of Pro|E, not evev in Creo 1.0 or Creo 2.0., that I know of.
You can rename any subassembly or part, as shown below:Welcome to the forum.
What do you mean by "progressive number"?
What software are you using?Welcome to the forum.
If you're going to make several holes with different diameters, they can all be made with one extrusion. No need to keep selecting the hole command.
I just LMB on the view and a dashed border appears, then RMB for further properties.
Dimensions out-of-view in sketcher mode has been a chronic problem with PTC. My "work-around" to this is that I just rotate the model in sketcher and drag the dimension inward. I shouldn't have to do that. I think I will bring this up with tech support and see what they say.I don't have this problem in sheet metal mode.
Hi Joey,Let's start with the first problem (ex1.prt.1). Here's what I'm seeing in your post:1. The shear-moment diagrams don't match your blue beam sketch because you ran an analysis with both ends of the beam fixed in xyz. The shear diagram shows -10 then +10, and that's what you get when you fix both ends. However, your example shows a fixed end and then a roller on the right side. To simulate a roller constraint, free the X translation and free the Z rotation.2. The greatest moment is in the center of beam, and this would not be zero.3. The shear-moment graphs show a beam length of 50mm, but the sketch show 5cm.4. Modeling hint: You don't have to sketch the curves to make the beams. I made the beams point-to-point. Make all your points first, then connect the points with beams in Creo Simulate. Look at the file I uploaded as an example.File uploaded.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.