Recently active
Is this the solution in NX?
The analysis in the attached pdf that you're interested in uses roller bearings, whereas your model has ball bearings and a cage around those bearings. A very complicated model to run in contact. The attached analysis uses a shaft through the inner race, and the outer race is in contact with a plate, and runs a 2D analysis.Your original post was how to calculate a bearing load, and I will show you how to do this. I'm going to show you how to apply a bearing load to a component and then check the applied load. Follow the below figures.Figure 1: Select Bearing LoadFigure 2: Select the Inner Race SurfaceFigure 3: Select Preview to see the direction of the load, then select OKFigure 4: Bearing load appliedFigure 5: Review Total LoadFigure 6: Compute the Resultant Load (or Bearing Load). Always check your load after is has been applied.
What is supposed to be?
Delete all the rounds you have posted in the images and make just one continious round on the edge of the cylinder from the first image. It looks like 3 mm? Does it continue all the way around the cylinder? Post an image of it. Are you allowed to upload the model?Welcome to the forum.
Are you trying to measure the angle of twist for a shaft?
Well...that depends. If you create a model in Creo 3.0, save it as an STEP file, open in Creo 2.0, you could view it. And you could modify it some if you have the Flexible Modeling Extension.But if you want Creo 3.0 (.prt file) to be opened by Creo 2.0, no, this cannot be done directly.
You can IMPORT the file with Creo Parametric 3.0 (F000). I've done it many times already. See my attached post on importing an entire H-60 lightweight model. This was made in CATIA V4.http://communities.ptc.com/message/257550#257550I just imported the entire CH-53E surfacing model from CATIA V5. I would post it here but I'm at home. I've also imported Solidworks.
I don't think Creo Simulate can perform impact analyses.
You would have to sketch the entire system, including the loads, in order for the community to understand your requirements.
This is how loads are applied in StressCheck, by traction, which is psi. StressCheck calls it a traction load, but it's really pressure. Just use a pressure load.
With a single p-element, the stress can vary from one end to the other.
If you have Creo 3.0, all you have to do is import it.
Is it not possible to create your own drawing template with the desired sheet size, and then all you have to do is load that template everytime you need it? I wouldn't need a config.pro setting for that. What do you think?
When you get the GUI to change units, it should look like the below image. If you have an assembly, don't forget to check "Include submodels".
How many elements are in the assembly?
Lucky,The load is not calculated in the attached model. It was predetermined by the user as 2000000 N and entered as such. The hinge acts like two cantilever beams, because the center of the hinge is constrained in global xyz. Even though you have Force/Area, the ends of the beams will bend and have less stress than the center, as shown below. If you want to understand how the load behaves (shear load), try drawing a shear/moment diagram on a beam with one end fixed and the other end free.
Can you upload a screenshot of the problem?
Charles,Amit already has another post on this. See the attached link:http://communities.ptc.com/message/259732#259732
I think what you're asking for is code verification. You want to verify if the code was developed correctly? You want to know the stress, strain, and displacement calculations based upon the finite element method.There are three components to solution governance when dealing with the finite element method:1. Code verification2. Data verification3. Solution verificationCode verification is the developer's responsibility. Data and solution verification is the end user responsiblity. Solution verification is by convergence on the data of interest.You can plot convergence on the data of interest, say to within 1%, to verify the solution. Validation would be by strain gage testing, to validate the FEA solution.To see if the attached model in this discussion "behaves" correctly:1. Plot the displacement and animate it2. Plot the desired stress/strain3. Plot solution convergence on the data of interest to within 1%If you want to attempt this by hand calculations, try a simple beam constrained
Can you upload the model?
Download from:https://support.ptc.com/appserver/cs/software_update/swupdate.jsp
What is the material type?Is this just an LDA on a block of material as you have shown?
1. Okay...that clarifies some things, because you did not mention LDA in your original post. You can still constrain the surface with a global constraint and fix the z direction. Then you will have to add more constraints to the other surfaces and select which directions to allow movement or no movement.2. The measure can be found as shown below.
Yes.
What do you mean by "load behavior"?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.