Recently active
Creo 3.0 M010 is ready for downloading.
Thanks. That's it.
Does anyone know how to make the arrow style solid black or filled? Thanks in advance.
Anoop, Currently, your model has no properties, as shown below.
I assume that each rib profile (or bulkhead) may have it's own contour, but there may be several stations in the middle of the ship with the same contour. I helped someone in the past with making the hull of a ship, but the drawing had all the necessary data points to make the curves (made my job easier), so there was no need to scan the drawing.When you say "scanned rib profile", are you talking about scanning the drawing or sections of the drawing with a paper scanner? You may have to scan different profiles to obtain the entire curvature of the hull.The example below is where I added an image to a datum plane, then traced the required features to make the body.
I have a NVIDIA Quadro 600 (Version 296.70), and I don't have this problem. The PC is HPZ800.
Huruj,Here are some links to making bevel gears in Creo (three part process).https://www.youtube.com/watch?v=bMXP9pvNX9Yhttps://www.youtube.com/watch?v=UyNI8tWI3Kwhttps://www.youtube.com/watch?v=bmJdnB6OSik
You may want to move this discussion to Analysis and Simulation.
After opening a model to create a drawing, the drawing is blank. Why is this?
Andy, I did that too, but there are no drawings, only a view of the solid model.
For this case, I just create a drawing from an empty template. I've done this for years.
I don't really need a template to open a drawing.
That doesn't work for me.
What do you mean by "add a view"? Model attached.
Date Code is M010
Andreas,I built this in Creo 3.0, so you won't be able to open it, but I posted the image. It's very simple, and I was only experimenting with your model. Here's what I did:Modeled 1/4 of the assemblyApplied symmetry constraints to both sidesPlaced three frictionless contactsRemoved the contacts between the shank and boreConstrained one end of the boltApplied 1/4 of the preloadApplied 1/4 of the cross-sectional area for preloadI was going to run this over again with an advanced fastener, but I just haven't had the time.
Andreas,When you stated a prestress in the bolt, are you refering to a preloaded bolt? I ran the model with two planes of symmetry, and you can see the stress contours in the plates (von Mises and max prin). It sounded like, in your original post, that you're really interested in the stress in the plates. Putting contacts betweent the bolt shank and the bores won't do any good, because there is really no contact between these bodies.
Andreas,With Creo Simulate 2.0, you will have to make two seperate runs to obtain the desired pre-load. Creo Simulate 3.0 has a check-box to account for stiffness (shown below), and the operator doesn't have to manually make two seperate runs to obtain the desired pre-load.I've attached a couple of documents to show you how to get the right pre-load using Creo Simulate 2.0. The fastener analysis tool is not a substitute for multi-body contact of fasteners in holes, as there is really no contact between the "bolt shaft" and the bore.
This is one type with the STEP file attached.
I would really like to see the model, how it was constructed for the finite element method.
I saved a spur gear yesterday as .stl, and I tried to reduce the size (KB). It went from 151 KB down to 77 KB, by adjusting the chord height and angle control (shown below).
Paul,Are you allowed to upload the model and some screenshots of the real-world problem along with a description of the problem (loads, constraints, region (s) of interest)?
If you have coincident surfaces, isn't this the same thing as mating surfaces? If so, wouldn't the tool Pairs Clearance tell you if the surfaces are coincident? Example shown below.
You can IMPORT NX files into Creo Parametric 3.0, but it will import as a neutral file.Welcome to the forum.
Paul,Whenever a gravity simulation is used, I would highly recommend verifying the total weight of the model. I use the IPS system of units and 1g = 386.4 in/sec^2. After you build your model, run a quick check to verify the total weight. For example, you can run a 1g load in one direction and see if the resultant load in that direction matches the weight of the model.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.