Recently active
What are you showing for Mass Properties (as shown below)?
Jason,If you can provide a sketch of the thread profile with dimensions, I can make this for you in WF4 and provide the instructions with screenshots. WF4 is very similar to WF3, and I don't have WF3 installed.
Martin,I was able to import the human head into Creo 3.0, as shown below.
Yes.
Lucas,The Sketch Setup is greyed out (shown below) because the trajectory drives the sweep. If you change the direction of the curve (trajectory), it will change the direction of the sweep.
Lucas,I cannot read your file, as shown below. I'm using Creo 3.0 commercial version.
Are you using a student version of Creo?
No...the curve drives the direction...you will have to change the curve.
Patrick,You've made a valid point, and I couldn't have stated it any better. It appears that the "problem" with the Product Development Team is that they do not work on a daily basis with a product as we do, and they don't appear to see the benefits of having this type of capability, and I don't believe you can convince them otherwise. It sort of hits you in the "gut", especially after paying maintenance for many years.
Gunter,The functionality was removed intentionally without submitting a Product Idea, therefore, the functionality can be restored intentionally without submitting a Product Idea.Submitting a Product Idea will not restore this, in my opinion, as I have already submitted 33 Product Ideas since May 16, 2012, and none of them have been considered by the Product Development Team.
Steve,If you're on maintenance, you may submit a Product Idea, as shown below.
I think it is possible. See if the below link will provide what you're looking for. shear&moment diagram - PTC Community
I like to below link for modeling spur gears in PTChttp://www.beyondmech.com/pro-e/cad-topic-27.htmlAnother method is in the attached PDF, but more complex.
Rocks1,If you have just a box with hardware, such as hardware from a library, and the hardware has no csys, then by all means, just mate it with the hole.I have to deal with large airframe assemblies, such as stringers, skin panels, floors, longerons, intercostals, etc., and they are assembled upon one csys, the csys of the airframe. Also, I receive them this way from the aerospace companies, such as Sikorsky, Boeing, and Lockheed.
It's very simple. When I'm building an assembly, I have already created all my components based upon the assembly csys, so the component csys and the assembly csys are the same. When I add the first component to the assembly, I just snap the component csys to the assembly csys and it's fully constrained and very stable. Then I just repeat this with the remaining components. This is a common practice in the aerospace industry where entire aircraft are assembled this way, such as the H-60.
I put a comment in your other post:https://www.ptcusercommunity.com/docs/DOC-6827
Whenever I'm putting assemblies together, I referenced all the components to one cys, and I don't have any problems.
The message Outdated Component/Feature is a notification for components or features with references that have changed since the last regeneration.The only way I know to fix these notifications is to open each failure and make new references. This is fairly easy to do, but it sounds like you have a lot of them to fix.
For the type of font you have selected, it may be the right behavior. It depends on which fonts you select. Some of them will dip below the line, and some will not, as shown below.
A common modeling error is users make a reference on the geometry and then change the geometry, breaking the reference. Try to make references off datum planes, axis, csys, and points, references that won't change throughout the assembly or component.If you have a large assembly, it may be that the references to other datum planes have been broken.
Ruben,You can connect the two pipes using the Extrude method without using the Shell. For example, the below images show the two pipes coming together by extruding the longer section up to the surface of the first section. The two pipes have the same OD but different ID, so they are different in thickness. Hope this helps some.
Adam,Are you referring to the Options in the below image (Creo Parametric 3.0 M020)?
Are you opening the Assembly in Creo Parametric or Windchill?
Can you upload run summary file (.rpt)?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.