Recently active
Use the View Manager to save your default view.
I saw this often in WF5 and XP, but I've moved on to Creo 3 and W7. I've never experienced in Creo.
Vaibhav,Can you upload an image of your assembly and how it's loaded? You have one plate, two shafts, and bearings for multiple shafts.
Gorka, Here is some information to get you started. Read the documents in the below link, especially the last one. https://community.ptc.com/t5/Analysis/P-vs-h-type/td-p/101228
Jon,Do you have real images of the desired product?
Chris,For every type of analysis capability that Creo Simulate has, you will need a best practice, and that's a lot. For example:1. Nonlinear multi-body contact with finite friction2. Linear static3. Fatigue4. Gravity simulationsetc., etc., etc.DId you have a specific type in mind?
Johan,It may be possible if you're just interested in slippage. Contact with infinite friction is used as a slippage indicator, but I've never used it on cylindrical surfaces, just flat surfaces. Give it a try.
Daniele,You can try to import the ACIS .sat file into Pro|Engineer.
We only have experience with Faro, and it does very well for what we need.
Daniele,Most 3-CAD packages have the ability to export IGES or STEP file extensions. If your software can export these, you can then import them into Pro|Engineer, but Pro|Engineer is not a simulation and analysis software by itself. You will have to acquire a product like FloEFD or you can analyze the models in a software like ANSYS, which has CFD. PTC's simulation and analysis software is now called Creo Simulate (formerly Pro|Mechanica), which does not have CFD capability by itself either.The file extension .adsk is a 3D solid modeling extension, but you cannot import this into Pro|Engineer. The other two extension that can be imported into Pro|Engineer are .dxf and .dwg, but this are drawing file extensions.
I reviewed the online tutorial by Mark Taddonio, and it was well worth the time to view it. However, there is one thing that should be brought to the audience, and that is no matter how many elements were used, the peak stresses didn't vary that much. There were three runs in the tutorial with the following results:1. 81.3 MPa2. 80.9 MPa3. 82.5 MPaAnd no matter how many elements are used, the results should always be verified with a convergence plot on the solution. Also, if the intent is to reduce the number of elements, this model has symmetry, and it could have been cut in half lenghtwise.In conclusion, more p-elements doesn't necessairly mean a more accurate solution. But the video does show how to create and manipulate meshes.
I would try the Freestyle tool.
A multi-pass adaptive can take up more memory.
Mauro,The problem with using a boundary blend in the corner is that there is discontinuity in the reflection analysis (see below image circled in red). I had already tried that method, but I didn't like the results. And yes, there were additional sketches in the model from experiments, I just left them in there. Thanks for the reply.
Shashank,The model is attached for educational purposes, as it may not be exactly what you're looking for; and it was created in Creo Paramteric 3.0 (M040) Commercial Version.
Shashank,See if this is what you're looking for (image below). I can post this model tomorrow.
Sachin, See if this is what you're trying to implement: . - PTC Community
Are you stating that you're having problems getting the two parts to attached during the automesh? What do you mean by, "getting the two parts to attach"?
Lucas,Did you try simple hand calculations on the upper center hole for shear tear-out and bearing?
Richard,GEA (Geometric Element Analysis) is the acronym RASNA used to define the adaptivity method where the fidelity of the model is increased by raising the polynomial order and the element is mapped to the geometry. It's still the same with AutoGEM (GEM means Geometric Element Mapping). Creo Simulate doesn't use the GEA acronym, that I know of. That's a bold statement to say, "this is not FEA". What are the two techniques in the rejection? P vs H?In principle, any problem which can be solved by the h-version can be solved by the p-version and, conversely, any problem which can be solved by the p-version can be solved by the h-version. There are large differences in convergence rates, however. For example, it was demonstrated in one well-documented plane elastic model problem that to achieve one percent relative error in energy norm (which is similar to the root-mean-square measure of error in stress), approximately 1000 degrees of freedom were needed wi
In principle, any problem which can be solved by the h-version can be solved by the p-version and, conversely, any problem which can be solved by the p-version can be solved by the h-version. There are large differences in convergence rates, however. For example, it was demonstrated in one well-documented plane elastic model problem that to achieve one percent relative error in energy norm (which is similar to the root-mean-square measure of error in stress), approximately 1000 degrees of freedom were needed with the p-version and properly designed mesh, whereas 10 million degrees of freedom would have been required with the h-version, utilizing 8-noded quadrilaterals and uniform mesh refinement. For details, refer to p.190 in Szabo and Babuska, Finite Element Analysis (1991). There are other important areas where the p-version has clear and substantial advantages: adhesively bonded joints (where very large aspect ratios are required), structural plates and shells, fracture mechanics,
Thanks Denis.
Erik,Are your contact analyses failing due to contact with finite friction? That's what I'm asking.
Ketan,Can you upload a sketch of how you would like your drawing to appear with coordinates? You can identify a coordinate in any drawing with a note. Since you're dealing with a 2D planar drawing, there is an X and Y to every point relative to the csys. But you want to identify a dimension, not a point in space?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.