Recently active
That's a different model from the first one you posted.
Here's what I'm getting from your testpart.prt.
I'm not getting those. Try importing the IGES file I uploaded.
I think you need to unhide the features in the layers then save the layer status.
You don't have to use Copy Geometry as I showed in my example. If you just Copy/Paste then save it as an IGES from the original, that will work also. If you have Creo Parametric 2.0, you have the Copy/Paste in the toolbar. I just wanted to show you about Copy Geometry. Copy/Paste on the original model is faster. But you stated that you don't have Copy/Paste?
I was able to get the curves into an IGES file for you. I just imported this into Creo to see if it was valid, and it is. I've attached the IGES file for you. You had a lot of the features hidden in the layer tree. Let me know if this works for you.
Ketan,You should be able to achieve a wireframe model by following the below instructions and images. This is a demonstration on a simple boundary blend.1. Copy/Paste the edges of your boundary blends in the original model. You may have to set the smart filter to Geometry. Notice in the model tree there are four copied curves from the boundary blend. Save the model.2. Start a new model and use Copy Geometry. Turn publisher off. Look for the reference model and copy the chains (curves) from the reference model. Select Ok.3. Notice in the model tree there is a external copied id. This model can be saved as an IGES.4. In the Export IGES dialog, select Datum curves and points.5. Import the IGES file. You should get an exact wireframe model as the original.Let me know if this works for you, as it should. Just apply the same methods for your model.
It may be that you didn't select datum points and curves. Look at the sample below that I just posted.
Delete the unwanted surfaces.Be sure that only Wireframe Edges is selected when exporting.OR...You could copy the desired curves within Creo under a new model, then save as an IGES.I just saved a wireframe IGES export without any complications (Creo 3 M100).
Never seen anything like that before. Are you having a graphics card problem?Welcome to the forum.
If you're allowed to upload the model, I will take a look at it.
Not that I know of. The 45XD is built in functionality in the pull-down.
Shashi,Don't forget to vote for yourself.
Are you allowed to post a screenshot of the previous CAD drawing with the dimensions?
If a spring is made as a sweep using a trajectory, then you can just measure the trajectory.
I must say it is a pleasure to meet you in the Community. I started using Pro|Engineer V18, and when 2000i2 came out, I purchased your book Pro/ENGINEER 2000i2. And I still use it at times to this day, even though I'm on Creo 3. I really like the book, because it has a section on Pro/SHEETMETAL. Best Pro/E book I ever bought for that version of software. You made every lesson so easy to follow with the images and click-by-click instructions.
But it's not out-of-the-box (OOTB) functionality.
Actually, you can measure the length of any coiled spring. Remember, a cylinder has two surfaces. Notice the image below, where the entire length of the spring is measured. This is done by copy/paste one side of the cylindrical surfaces, and then measure the total length of the edge of those surfaces.
I've added a Product Idea to be able to change units on-the-fly.https://www.ptcusercommunity.com/ideas/7871
Could you elaborate on this? Can you provide some screenshots?
Excellent. You can do it this way too.
Hannah,Here a more in-depth video on Direct Editing in SW.https://www.youtube.com/watch?v=u5bASMMkNtQ
Chris,Yes there is, if I understand your question. Set your units to FPS then measure, as shown in the below images.
What is the other CAD package? Welcome to the forum.
Hannah,Once you import a neutral CAD file into SW, you will need to use the Direct Editing capabilities to modify the model, if you have them. If you're already familiar with Direct Editing, that's good. If not, here's a video on how to use it. Direct Editing in Creo requires an additional license, but I don't know about SW. Check your SW software to see if you have it. The attached video is an example where a neutral file was imported into SW for editing. In addition to all this, Creo has the capability to import SW files, modify them, and export SW files in the SW format.https://www.youtube.com/watch?v=uSXdOGb3o4I
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.