Recently active
I’m not sure if I understand comment #4, but you can certainly control which view you would like to sketch from. If you have a datum plane or even a surface highlighted before you select the extrude command, for example, Creo will automatically orientate the model for you, perhaps to an undesired view. Make sure nothing in the model is highlighted, and you can control it with the placement tab then define the view. I find myself often overlooking this, as I will have something highlighted and the model will flip to a view that I didn’t want when performing certain operations. As much experience you have from the Pro|Engineer days, I think you are probably aware of how to define a sketch placement, but Creo has the automatic function.
Davor,Who invented the first splash screen?
If you want to warp one half, then the other half, you will have to make two separate part halves and place them in an assembly. If you extrude one half, then extrude the other half all as one part, you encounter the problem you just described.
The bottom line is, it currently does not exist.
Before I submit a product idea, I was wondering if there was an existing way to notify users of the Community if the attached files are student or commercial. I would like to see a way to notify users if they are going to upload a student file or a commercial file to let the readers know in advance of what kind of file it is. So many times I have downloaded a file to work on and found out it was a student version of Creo, a file that cannot be opened in a commercial version.
Here's why you would not want to make this with Warp. Notice how the washer twists, and I had to make two halves and place them in an assembly. And it doesn't mate very well on the opposite end.
I rather have them do one more step than for me to ask them if it is a student version file and they have already posted it in the commercial forum. Now, they will have to post it again in the academic forum, another step.
Whoever programs the Community web site would know the best approach.
I never stated Jive notifies automatically. I stated that there would have to be a pop-up window when attaching files, and that pop-up window would have functionality to notify readers if the file is student or commercial.
Did this post answer your question?
I just don't see "user education" preventing the uploading of commercial files in the Creo forums. If all of the student files would be uploaded in the Academic Program, then yes, that would work fine. But everyone who post questions with student files don't always go to the Academic Program. So if Jive would tell the users that are about to attached students files (or academic files) to move the discussion to the Academic Program, that would be great. But there is no warning in place for that. So what I try to remember before I respond to an attached file, I ask the author if it is a student version file, and if it is, then that author has to start another post in the Academic Program to receive assistance. And I'm not talking about just a few files, there have been a lot of student files posted outside of the academic forum.
Hi Senna, See if the attached discussion will help you, as I had raised the same question. Solved: Re: Creo Simulation 2.0 M050 - Inertia Relief - PTC Community
Even though you have asked the user to identify the file type before uploading, it just doesn't work very well. When attaching a file, there needs to be a pop-up for the user to mark the file type, and as David pointed out, even the software version. A lot of questions are posted under Creo, and not in the academic forum, which are still student versions of Creo.
Hi Kriste, I have not used the hard drive for memory since WF5, because back in those days, the RAM allocation was about 8GB. So I would allocate swap space on the hard drive to run larger models, and it would work, but ran much slower. I submitted a product idea years ago to address this problem, to increase the RAM allocation for Creo Simulate. The product idea is linked below, and you can see some comments from Mark Fisher on product development. Welcome to the forum. Creo Simulate - RAM Allocation for 64-bit Windows... - PTC Community
Congratulations on finding meaningful employment and working with Creo 3. I hope it continues for you, and I’m glad to see that you like the ribbon based GUI vs the old pull-downs, even though I still like the pull-downs myself.
Tobias,I would like to know how you got the Free Curve to snap to the datum points after selecting the Shift key, because that doesn't work for me. The below image shows five datum points on an active plane. When the Shift key is selected, the Free Curve will not snap to any point.
What version and date code of Creo are you using?
How about this Product Idea?https://www.ptcusercommunity.com/ideas/8048
If Creo is old-fashioned, what software do you think is new-fashioned?
That works if you're using Edit Curve, and that I knew. But to make this work with an initial curve, I don't see it. Thanks.
I would like to set this up for myself, except for importing models that were created with metric units and will always come in IPS units. Thanks for sharing.
You have to change the units, it's not done automatically.
File > Prepare > Model Properties > Units > System of Units > Select Units > Set
Curve though Datum Points will snap to each point, as shown below, not using the Style Tool.
I missed that part (you have already ordered). So Lenovo is the winner!
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.