<strong>Creo Parametric related:</strong> Expert Machinist, CMM, Molding, Casting, Additive, EMX topics, and more
Recently active
I'm in the process of developing a thread milling process but I am not getting the correct tool path. I need a single pass tool path but I'm not able to find the right parameter combination to get single pass. I using a solid tool defined in Creo to simulate a multi-tooth cutter.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
I currently use Creo for our machining software. We have three HMC's and the software works well. We are about to purchase a Vertical Turret Lathe with machining capabilities.Will Creo support or work for this type of machine? This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Is anyone programming one of these in Creo Manufacture? If so who did your post? Are you using simulation software?Thanks in advance.........This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Hello! I´m an engineer student and doing my final thesis on Creo Parametric 2.0. To be more specific, i´m researching different ways of using pictures or vector graphics as a stencil for extrusions and forward to .dfx for laser cutting etc. manufacturing. The main idea is this: I download a "dog face" from google, place it in a plane in Creo Parametric and draw the lines with splice tool etc. That is kind of slow, crappy and the results are very inaccurate in my opinion. There must be other easier ways to recognize the shapes of pictures or vector graphics etc....? My purpose is to find out different ways of doing this, test the ways, report my findings and do a tutorial of some sort. I´d be very happy if I could receive some user experiences of similar situations from more experienced Creo users so I could test them myself and use them in my report. Have a nice springtime! -EeroThis thread is inactive and closed by the PTC Community Management
I've found that when using Finishing operations that its outputting almost exclusively points instead of arcs (I's and j's) and its making my files massive when its not necessary. This happens even with simple shapes like round posts and holes. The Parameter "Circ_interpolation" is set to "Arc_Only". Is there something I'm missing here? I'd really prefer to output more arcs and cut down on file sizes where possible.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Anyone have a segment of a FIL file doing probing on a Fanuc machine for Gpost available?This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
This is just a general question for those who run Wildfire / Creo without any PDM software.How do you set up your folder structures on your server / CAD machine, also is there any advice as to the best way to manage file etc in this way.I am guessing that it is going to be what ever suits best, but ways to avoid etc would be good advice also.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
I am trying to use auto cutline in Creo 2 to mill a few hemispherical pockets with a ball end mill. I've used the auto cutline before on similar recessed pockets and it usually goes well.The problem I see in this feature is that there is no way to specify the CW or CCW direction of the cutter as it helicals into the pocket. If it defaults to the way I want to go (climb milling) things go fine. If it produces an upcutting tool path, there seems to be no way to change it.For today's project, an internal hemispherical pocket, it wants to helical CW from the top with the spindle specd at CW (upcut). If I edit the path the cutter plunges to the bottom of the feature and helicals upward.Anyone else have luck with this one?Thanks.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure
Hi,Can anyone tell me the difference between .ncl and .tap files please
I usually make Mill Volumes and Mill Surfaces to create my own sequences to rough out a part rather than make use of the Mill Window based Roughing / Re-Roughing Sequences that Creo seems geared toward. That is how I've been taught how to program and have been steered away from using the latter options. It seems safe and usually predictable. I am curious to know how others feel about the Roughing / Re-Roughing method of getting the job done. It looks to me like it could potentially save a lot of time, but the re-rough tool paths seem very unpredictable. I did try a couple of simulations and one of them had a big gouge that I couldn't get rid of in the Re-Rough.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so anot
Thank you to Bill for the parameter I needed to change. Works like a charm. This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
I am looking for people who have personal experience with a company that has done this for them.I know about ICAM, PostHaste and Gpost(Internal)Any other options that are really good?This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Need help setting up a custom drill cycle for thru spindle coolant drills in a VMC. I will be spotting the holes 2xD with short drill first. After the holes are spotted this is what I am looking to do:Enter hole at a lower rpm (around 300rpm)Turn TSC ONRamp spindle speed to desired RPMDrill HoleReturn to origanal starting pointRamp RPM back downTurn TSC OFFgo to next holeCustom drill cycle seem like the way to go to do this just not familar with them and the daocumentation is lacking to say the least. We drill anywhere from 100 to over a thousand holes in one block. I have been able to use normal drill cycles for the shorter drill but when using 15D or 20 D drills they will snap if the tip is not supported in the hole when ramping up to proper spindle RPM. I might want to try a different variation where the TSC coolant stays on the entire time instead of on/off for every hole. I will say that I do not program everyday but trying to utilize the machine and tooling to their potential. Th
Folks,I'd like to change the lead-in radius when rough-milling. The cutter chatters because the radius is too small so I'd like to increase it. I've looked all over the place and cannot find any way to change it. Does any one know how to do this? BTW I'm on Creo 2, M100.Ray AvilesThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Dear partners,I am working in a graduation project with PTC Creo Parametric, it is about a machine for make torsion springs, the shape of these is like a Z, I would like to know if there is any solution from PTC for this job, I need to make a simulation of torque motor, I need to simulate the deformation wire for find the maximum torque motor, I have not been able to find a tool that allow me make this simulation,I will be grateful if you my dear partners can collaborate me with a solution, or tips about How can I solve the problemThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Every time I open Creo Prismatic and want to use the Multisurface Milling Extension I have to go into the options menu, refresh the licenses, and select the correct license. Is there a way to make this persistent so I don't have to do this every time?This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Hi i made a postprocessor using GPOST for a double turret, double spindle lathe on Creo 1The most heavy thing was to force user to insert manual commands on sequences to tell wich spindle to useIn Creo 3 i can define a lathe machine with double spindle and simply choose what i want to use from a dropdown menuGpost doesn't manage this information How to simplify user life (and why not... my own life programming GPOST)?ByeOsvaldoThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
how to machine the part with Slice by Slice strategyThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Hi,I am trying to create a post-processor for Heidenhain iTNC 530 controller.I have few questions in writing blocks to PP from Creo.1. How to add BLK FORM 0.1 Z X-0 Y-0 Z-77 from CAD?2. What options in option file generator or Creo has to be enabled/ disabled for M127, M129?--DhineshThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
I am looking for some inter-company help with Creo Manufacturing implementation, post-processing, and managing files in Windchill inside Ingersoll-Rand.Scott JohnsonManufacturing EngineerMocksville, NC siteThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
I have had limited expirence using this 3rd party addon within Gibbs Cam but i was wondering if anyone had tried integrating it with NC manufacturing. The tool paths it generates look alot better than our constant load paths. http://www.celeritive.com/index.phpThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Tell me, how to find the flatness and the Ra value in the manufacturing?This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Hi, I have a arbortext editor installed in my machine, can somebody help me on how to configure and compile a new dtd? Also i would like to know what necessary files are required to configure the same.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Pro/E used to have the option to use a part to subtract material from another. Does Creo 2.0 have this? I can't find it, or find anything on the web in this regard. I have a student that wants to make a matching thread in another part. This used to be easy, but now I can't figure it out!This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.