Recently active
It would be beneficial to have a button to add a family table instance to drawing. At the moment there is "Add Model" button in the menu manager but this requires user to browse first the generic part and then Creo lets user to choose the instance to be added to the drawing. This would be particularly useful with sheet metal parts if a flat instance is needed to the drawing as an informational view.
The model DTL file has a setting called "default_tolerance_mode". This setting controls the tolerance mode for both created annotation dimensions and the feature dimensions (the sketch dims, driving dims). For MBD it would be helpful to be able to control the tolerance mode independently for feature dimensions and annotation dimensions. Maybe a new DTL option called "default_annotation_tolerance_mode" that would apply to created annotations while the existing setting "default_tolerance_mode" would then apply to just feature dimensions. The reason behind this is that for MBD created annotations are used almost exclusively and it would be desirable to have the created annotations have a tolerance by default while the feature dimension would not have a tolerance.
It would be desirable - to interrupt axis- to shorten/extend axis by dragging the ends in the same way you use it with extension lines.
I mean the possibility to reorder the analises within the model tree. Now the order is chronological but often you make analyses that are similar, with only few changes, in different instants and so happens they aren't one after another. But, for a better mental order, it's convenient reorder them to have "a kind of group of similar analyses". ThanksBye
Hello, In a transient thermal analysis, for a boundary convection condition, give the possibilty to users to combine temperature dependent convection coefficient and bulk temperature dependent to time. Actually, when we try to define in Creo Simulate a such boundary condition, "Creo Simulate" give us the following message (see please the JPG file) Thank you in advance Sidi
3D Thickness control analysis for complex models can take hours, sometimes even days. It would be nice if this time could be reduced and of course the parallel calculation could help (even if the best way would be to reduce the complexity of the algorithm that performs this function ...)
It will be great having access to replace unrelated component funcionality using OTK/PROTK Nowadays do that programmatically will require a lot of work, specially if the component you want to replace is a missing component, while do that using replace UI is a really simple and straightforward process
I mean the possibility to put special items on the geometry that can start actions like forces, motors, ect....It would be a more simple way in relation to the current ways. ThanksBye
When import the attached model after exporting it in the STEP format, the surface of the model is divided without permission. The customer wants to improve so that the information of the exported model is not converted arbitrarily.
Demande d'ajouter un paramètre interne afin de pouvoir récupérer en mise le nom de la table de tolérance associée à la pièce
Creer un outil permettant d'ajouter automatiquement le(les) symboles d'une dimension dans le texte d'une autre dimension. Dans les propriétés de texte (cote, note, tolerance geom) avoir la possibilité de sélectionner un paramètre ou dimension et d'ajouter automatiquement son symbole (&pxx, &dyy) dans le texte. Pour les paramètres : selection la feature dans l'arbre de modèle obtenir la liste des paramètres internes sélectionner le paramètre pour ajouter son symbole à la note/texte de cote Pour les dimensions Selection directement la cote sur la mise en plan pour ajouter son symbole à la note/texte de cote Exemple : Texte dim A : &p99x Ch. &d10x&d11 -> x2 ch. 0.5x45° Le p99 provient de la selection du nombre d'intance d'une repetition
Afficher l'arbre de modèle et l'arbre de couche en même temps dans le navigateur par des fenêtres "dockable"
Actuellement les tables de trous ne supportent pas les parametres thread_depth et drill_depth. Les profondeur sont calculé directement dans CREO lors de la creation des trous standards. Les profondeurs proposé par defauf ne correspondent pas au standard (NFE 25-030). Ajouter les parametres thread_depth et drill_depth à la table de trous afin de pour piloter ces 2 profondeurs comme les autres parametres ( FASTENER_ID BASIC_DIAM THREAD TAP_DR ....)
Ameliorer l'interface utilisateur pour les opérations d'usinage : Supprimer le tableau des paramétrés de l'opération et le replacer par des onglets, des zones de saissie, des menu déroulants pour les options, des schemas ....
Hallo, Every real vibrating system has anti-vibration mounts to isolate the system form ground. Today there isn't any possibility to simulate this into Creo simulate. This is serius lack because the vibrating system is strongly influenced from the elastic behavior of its mounts. I suggest to implemet this by adding a two way spring table: today you can input the spring stiffness, and the spring use the same value of the stiffness both in extension and compression condition. It would be sufficient if it were possible to set two values of stiffness, one for compression, the other for extension condition in order to simulate pre-loaded elastic supports.
I propose a new config option: 'Advanced_reference_configuration' that let this Paste Special option always checked with 'yes' or unchecked with 'no': Thank you
When aksed to select a centerline when using the "mirror - mirror selected entities" function in the sketcher, any straight line, entity or reference selected should "become" a centerline. (A centerline should be created, using the selected entity or reference) Save clicks! preserve users! 🙂
Currently, the secondary dimension is truncated to be able to comply with not exceeding the value permitted by the primary dimension. The problem is that when the dimensions are displayed in reverse ("secondary [primary]"), the values are inherently incorrect. To further elaborate, we model in SI Units as we work internationally. Bur our parts are fabricated in the US, so we draft with the primary dimensions displayed as Imperial. For this example, drawing dimensions are shown as .XX +/-.xx [.Y +/-.y] where X is in inches and Y is in millimeters. A modeled dimension of 100 +/- 10 mm currently displays as: 3.9 +/-.3 [100 +/-10] This is terribly incorrect, as the dimension above would require the displayed secondary dimension tolerance to be truncated to a max of 9 mm to fit within the bounds: * max bound of 109.42 mm = 3.954 + .354 in (this assumes 5 is alway rounded down) * min bound of at 89.05 mm =
I create large machine level models with an enormous number of connections. The "Integrated Mode Error Checking" step takes about as long as the remainder of the run in some cases. I would like to either make this algorithm much more efficient or offer a lighter version of this check that performs only what is absolutely necessary for the solution to kick off. I'm 100% OK with the run failing later when it gets into the solution without providing much diagnostic information as I'm used to that having worked with Mechanica for many years.
We want to extend form and position tolerance as check dimension in Creo Elements/Direct 19.0 M050 Annotation (see screenshots).
When attaching Datum Feature Symbols, in almost all cases the user wants the datum feature symbol to be normal to surface that it is being attached. I am suggesting that for these cases the annotation plane be "Normal to surface". Obviously this case won't work for all annotations so this could be an option that shows up for a subset of annotation for which it makes sense (datum feature symbols included).
currently no notification function available for Open File Cancel Button
everyone who has used the advanced design modules yet (Relations) and created a long list of relations will know how annoying (even frustration) it can be if you need to search for that 1 relation that you want to modify. if your relation set i well build, then you mostly do not have to change more then a handfull of relations, but you need to search for these reltions every time again when you want to change them.at today there is no possibility to mark these relations as being more important. There is no possibility to put them on the top of the list.there is no possibility to filter out some sorts of realtions, so for example coincident relations are not shown. this is defenitly not an intuitive UI.the idea that I suggest goes even further. it would be great if PTC develops a sort of browser where the user could manually add his "favorite" relations.
It's not possible to modify the diameter of a cylinder but only it's radius and the dimension created by flexible modeling is a radius.We would like to have a diameter dimension it's better for use in order to use it in a drawing. We never use radius diamention on holes / full cylinders.
User must use environment variable and dos command to borrow a license for max 14 days or for return early a license or for return a license that it is not check out correctly. All is difficult!!! I think that a user interface could be usefull and also the possibility to borrow a license for longer period.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.