Recently active
Just switched to Creo 5 and the default selection filters are so annoying. Now I have to add two more clicks every time I open a file or switch windows because I have to change the filter selection from Geometry to something logical like Parts for Assembly mode of Features for Part mode. The My Filters option doesn't help either because you can't set that as the default. PTC please update the filter selection interface so users can see which filter is selected in My Filters and so that the filters can be defined in a convenient table interface. Reference: Is there a config.pro option to set a default selection filter value in Pro/ENGINEER Wildfire 5.0 and Creo Parametric https://www.ptc.com/en/support/article?n=CS19200 After digging into it a little more, I found you can actually set the My Filters setting as the default by selecting the "Set my Filter as the default selection filter" box. (File > Options > Selection). However, all that sho
Currently it is not possible to show sketcher based ordinate dimension on 3D level using Show Model Annoations (it can only be shown in drawing level) - See example attached. PTC is not planning to fix this as it is regarded as standard/intended functionality (PTC CS152204 / SPR 2856507/2203317)This is also a frustrating limitation when trying to apply other annotations to the 3D model, for example a GTOL on an ordinate dimension.You have to re-create the dimension (driving) and then only you can apply the GTOL on an ordinate dimension in 3D OR use linear dimensions, which are not always practical.
Currently there is no way to map user defined colors to different pens in the pen table. This forces all user defined colors to plot using Pen #1. It would be nice to set the user defined colors to a new pen (in our case so that we can set no color and have the PDF inherit the user defined color of the symbol). Currently there is no way to do that. The ASME standards now allow for colors to be used in drawings and our engineers would like to use custom symbols with custom colors on drawings and create the PDF properly, where geometry lines (Pen #1) are all black and the custom symbols retain their original color.
As in article CS97061 described, the redo and undo functionality is not available for mfg Features. Please add this in future
It would be very nice to have the possibility to supress single Features in the tool Motion tab of mfg Features. Similar functionality to model tree.
The actuall behavour of pattern in the mfg mode is not good. When I make a pattern of a part witch is classified for example as a fixture, all pattern parts should be fixtures to. Actual i have to do this manually
Actually, the automatic material removal cut works only for 3-axis trajectory milling Features. This functionality should be improved also for 4 and maybe for 5 axis
Wouldn't it be easier to access layer tree as a tab, like "Folders" or "Favourites" which are just next to model tree in the browser? It would save us one useless click. More generaly, a ergonomic study based on "useless click removal" would be a good thing for CREO.
At present we are unable to Save a backup of an assembly containing Many sub assemblies and child parts into a new folder along with the drawing files without altering the Model / Drawing names. This improvement will be helpful to many of the Creo Lovers.
In the measures window of an assembly, in the mechanism environment, you see all measures regard all sub-assemblies.What I suggest is a way to "filter" the measures in a better way, and a manner could be a "tree".
There is a way to link the line numbers or find numbers between WindChill and Creo as documented: https://www.ptc.com/en/support/article?n=CS197902 https://community.ptc.com/t5/Windchill/Find-and-Line-number-support-pdf/m-p/449900 and other places. This is a good starting point. However, this requires manual entry of the values within the model tree for the component level parameters. The issue with this is that Creo will fail checkin of an assembly if, for example,: There are 10 of the same screws and only 9 have the findnumber field entered (you missed one) There are 10 screws and you gave some of them one find number and others a different find number (you forgot some of these screws were higher up in the model tree with an already assigned number) You gave these 10 screws a find number that was already assigned to something else Getting the values entered correctly, effectively and quickly is almost impossible in even "smallish" assemblies when: Components are embedded
Please find attached images & the model, to demonstrate dimensions display when the annotations are activated. Attached part is with mulitiple features& when we activate the annontation dimensions display, for some of the dimensions, the witness lines are not touching the object line.This is due to the sketcher dimensions created for the first feauture.But the requirement is, when ever the new features are created with specific dimensions, proper display of dimensions to be made automatic & ther should not be any manual drafting work. This will reduce the drafting time & will be very much useful, incase we want to automate the 2D drawing process.
When using imported geometry, a surface or quilt may be present that represents a thread. However it will not behave as a cosmetic thread does in relation to hidden/no hidden in drawing view. Would like ability to select surfaces/quilts, RMB Convert to Cosmetic Thread. Does NOT have to be featured just need to behave as a cosmetic thread.
In Part & Assembly Mode make Cosmetic Threads disappear in No Hidden mode.
For the creation of a revolve (over 360°) we used the option to select twice up to the sketch plane as an option. This generation method has the advantage for us that no angle dimension 360° is displayed when showing the dimensions. Now the product specification has been changed and this generation method is no longer supported. It is not even possible to select two different planes that represent different angles. This can be read in the CS296387. This is especially unpleasant because the generation method must still be supported for existing models. Only a new generation is no longer possible. Please vote for the fact that the creation of revolve with the option "to selected" supports two datum planes!
The "insert-mode" mode allows it to better understand the structure of assemblies and parts. In Sketches there is no such possibility. For more complicated sketches an "insert-mode" might be useful, so one can better understand the structure and dependencies.
Creo 4 can insert images (png, and jpg). Toolkit lacks this feature. It would be beneficial for automation if toolkit could insert images on drawings. Thanks
The reason this is important. When items are placed on either of these layers the display of these items can only be changed by removing them from these layers. This defeats the display status of the other layers as intended. If models are checked into common-space with items on these layers(hidden/shown), then the display of these items is no longer as intended by the layering schema. This will negatively impact other users as they are no longer able to predictably control the display status of model items.
The main outcome of this result is that it shows the volume contribution from injected plastic melt of each gate, and the result values are shown in percentage. Normally, a balanced gate contribution is needed for obtaining optimized results. Since the main focus is percentage and balance, location of the gates is not currently shown. These may be noted in the PPTX file after generating the report if desired. I think this would be a nice feature to have since we do not display sprues or runners as Moldex3D does.
Dans le menu d’édition du plan de référence, je souhaiterais pouvoir modifier les valeurs de 508.660 (Largeur et Hauteur) tout en conservant l’adaptabilité des plans de référence en fonction des dimensions de la pièce modélisée. Si je coche l’option Ajuster le contour en modifiant la taille de la largeur et hauteur, je perds l’adaptabilité. La valeur de 508.66 n'est pas modifiable dans une option de configuration. Peut-on trouver une amélioration pour configurer cette valeur ? Merci
When creating a break in a drawing, and you specify the leader line on one side of a intersected dimension and the intersected dimension (not the other side), you can't control the default break width. It seems to auto-create a large break. It takes whatever value is in witness_line_offset detail option and has some hard-coded proportional increase from there.
I simply suggest to add the possibility of selecting the time/frame directly, without the need of scrolling the cursor. If I want to see the frame 36 (as in the pic) I "digit" 36 somewhere.Bye
Please create a more robust library of standard symbols for ASME (ISO, etc) including the parting line symbol and other symbols found here (that are already not in Creo): https://www.tec-ease.com/gdt-terms.php Thank you!
When using solid welds in the preferences of the welding tool (see fig. preferences.png) it is often not possible to create solid welds, because the material side of the weld is interpreted wrong by Creo (see fig. material_side.png). Please add the (grey) material arrow for solid welds, too (compare material arrow from surface welds). When creating solid welds, it is not intuitive at all to use the button "Flip material side" without any feedback from the program. Regards, Konrad
the need to simulate the deformation of the product when it is printed, like simulate but calculating on the basis of shrinkage and temperatures of the mould. model deformed.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.