Recently active
I just changed the orientation of an annotation (free note) and it went way off the page to the point where it was impossible to find it. I was surprised to find out the the zoom to selected feature doesn't apply to annotations. This idea is to make it so you can zoom to an annotation to figure out where it is in the model.
Today, if we don't have the capability to assemble several components at once. If we want to assemble several components by default constraint, we must do it, one for one. That is very tedious work. It should be allowed to assemble several components by default constraint.
Currently a cosmetic sketch is hidden when behind another component in a 3D assembly displayed as shaded. A view of that same assembly paced on a drawing displayed as shaded will show the cosmetic sketch thru all surfaces. Sketches that are behind other components should be displayed as hidden the same on a drawing as they do on a 3D model. Reference case CS149095 and the views attached.
Scope: Flexible assembly When we define a varied Items Dimension, using Method "Distance", WWE can only select a plane and not request an offset. Workaround is to create an additional offset datum Idea is to integrate the offset to the function - see picture Regards
I was seeing the following video from NX, and I think the selection method, is quite good. https://youtu.be/flLVhBiyD2Q With this selection, is easier to select some geometry in our models.
Creo currently only allows the mirror constraint to vertices in sketch mode. Even if we select some arcs, circles and lines, and select the mirror inside sketch, the mirrored geometry per se, does not have mirror constraints, but instead, it's vertices get applied the symmetric constraint. While this is fine if the new geometry is not edited, ie, trimmed, extended, etc, it's rather annoing and time consuming that whenever we later in the process add fillets, chamfers, or trim and extend geometry, the symmetric constraints on the original vertices get deleted by Creo. There was some improvements with the option to fillet and chamfer, but keeping the original symmetric vertices and split the geometry between solid and construction lines, to avoid the annoying deletion of symmetric constraints whenever a simple fillet was added. Nevertheless, this does not solve all the common problems, whenever we need to trim or extend mirrored geometry. I suggest that the "Symmetric" const
It should be an option, to global interference to stop the analysis, if users want's. I have made a calculation with wrong inputs, and I'm unable to stop it. Know I have 2 options: 1-Wait, and restart the analysis, with correct inputs 2 - Force CREO to shutdown, reopen the projet and do the analysis. Both of them are not that productive, both of them take long time!
In interactive Creo, a user can replace one component with another, even when the replacement is not part of the same family table or interchange group. This is done by enabling the ‘Unrelated Component’ option on the Replace dialog (see attachment replace.jpg). We need the equivalent API support so that the replacement can be automated within a PDM system. If the replacement component is geometrically equivalent to the original, no user intervention should be required, and any constraints should be automatically reconnected.
Tried to weld two parts together. It seems that the geometry is not that simple.With a butt weld it works but if I trie to fill the gap completly when I try to fill the gap completely with a butt weld it does't work like expectedIt's depth is 14mm and it works only when I type in 13.99mm It's possible with this workaround to type in 14mm but you have to define a face offset of -0.01mm that it worksNot so nice for users to find this workaround.Is there a possibility for the programmers to make this easier?
Today, ModelCHECK has the ability to flag over-written drawing dimensions with the DIM_OVERWRITE option. This is a request for a similar capability for solid models. We'd like ModelCHECK to be able to flag driven dimensions on solid models that were manually overwritten. This applies to our drawingless data sets. We have internal rules, training, and practices to avoid this situation, but we'd like an automated way to verify that no overwritten dimensions snuck by.
Sketch Regions are now only available fit external sketches and this wat of working is not available in internal sketches. If available in internal sketches a lot of trimming has not to be done anymore. This maken sketches more stable and working more productive. Also areas may overlap. In that case simple click the areas which have to be extruded without having to create closed loops which do not overlap.
Analysis Features have to be one of the best kept Creo secrets. The ability to create patterns of Analysis Features (Lengths, distances etc.) would be beneficial from a productivity standpoint, even if it's limited to specific use cases such as being able to create a reference pattern from another pattern of features such as points... The most likely candidates would be geometry measures such as distances and lengths. Add in the ability to create repeat region reports (for X, Y, Z point measurements from a common datum coordinate system gets the Dev Team bonus points!!
Can we please get a config option that would automatically assemble the first part in the assembly to the default location?
1. Describe your environment: What is your industry? What is your role in your organization? Describe your stakeholders.Space industry. I am the mechanical team lead. Stakeholders are my team.2. What version of Creo Parametric are you currently running?9.0.2.03. Describe the problem you are trying to solve. Please include detailed documentation such as screenshots, images or video.It would be great to have a design critera for minimum thickness. This willl ensure that the part can be produced through AM.4. What is the use case for your organization?For components to our satellites.5. What business value would your suggestion represent for your organization?Mass savings on structural components can reduce launch costs and increase the mass that the satellite payload can have.
1. Describe the ProblemWhen we have complex calculations which need several minutes to be solved or when we want to run them on a calculation server, it will be good to have a batch mode as wehave in Creo SImulate. Example in Creo Simulate: 2. Are you using a workaround?Run the calculation in interactive mode.3. What is the use case for your organization?In our company, we design hydraulic components for hydrostatic transmissions, we democratized CFD's calculation, we have 29 designers using Creo Flow Analysis.4. What impact does this problem currently have on your organization?We have time's losses on CFD's calculations.
1. Describe the Problem When sketching in 2D detailing, lines drawn over a view of 3D model are always below the lines of model. This creates problems. Please provide either: - Creo drawing option to show sketched lines on top yes/no. - "Bring to front" / "Send to back" feature in drawing mode. 2. Are you using a workaround?Workaround is to make sketch line thicker and it will make it visible. But this is not satisfactory. Or we can edit PDF after export and there fix the visibility of certain lines.3. What is the use case for your organization?We highlight sometimes certain parts of view in drawings. Or have to draw something over it.4. What impact does this problem currently have on your organization?Unsatisfactory drawings and waste of time to fix them with workarounds.
1. Describe the Problem Reference: Ticket - 17627996 Article - CS155799 When creating a drawing template, a note can not be 'related to view' when the view is a template view. This should be allowed. We have a requirement that notes be related to views or objects, yet our own templates won't follow that rule. 2. Are you using a workaround?No. The engineer will need to do it on their own later.3. What is the use case for your organization?Engineers create drawings using a template with the notes under a view already related to the view.4. What impact does this problem currently have on your organization?The engineers will be flagged by our checking system that these notes are not related to view. The ENGINEERS will be flagged for a note that they didn't even create. The optics look bad, where the policy is to not have unrelated notes, but the corporate template DOES have unrelated views.
1. Describe the ProblemPlease comb through the app especially drawing mode and add undo and redo wherever missing. Do not throw away stack after save operations. Modernize. 2. Are you using a workaround?No. Maybe maokeys for redo.3. What is the use case for your organization?There are sporadic support for undo redo and when I need it - it’s not available. Worse off is undo / redo stack is thrown away after save operations.4. What impact does this problem currently have on your organization?Huge. Since the UI is clunky especially drawing mode, I need undo and redo to speed up my workflow.
1. Describe the ProblemI find dealing with accuracy a nightmare when you run up against it, and there is a number that can be found manually by trying many times to find a suitable “magic accuracy” setting that will regenerate all features. We need these accuracy issues to go away. I propose somehow to build a magic accuracy button/system which manages accuracy for me automatically so my models don’t fail. Especially suitable for tiny geometric entities like lattice structures. 2. Are you using a workaround?Manual labor3. What is the use case for your organization?Designers have to manage and understand the inner workings of creo to master the use of accuracy4. What impact does this problem currently have on your organization?Huge. Hard to sell explicit geometric kernel in an implicit world of solvers. Design intent unclear.
1. Describe the ProblemIt’s very annoying to have the default tabs be to a company website advertising IE and AI. It’s not useful and strange. Get rid of these default tabs and let user decide during install. Do not drive traffic to others websites on each time I install creo. 2. Are you using a workaround?Yes I have to tell everyone how to shut off with config.3. What is the use case for your organization?It’s a useless page and doesn’t feel like anyone is using it.4. What impact does this problem currently have on your organization?None. Just explain to people how to get rid of it.
1. Describe the ProblemThe new sketch selection widget is driving my customers crazy. It’s too easy to lose your selection with middle button which throws away your selection. Also it seems more clicks are required to get the loop or extra options. 2. Are you using a workaround?I have to explain to customers to be careful here and do not accidentally hit the middle button or you accept the sketch which discards your selection.3. What is the use case for your organization?Having to start over.4. What impact does this problem currently have on your organization?Painful experience having spent minutes on the perfect selection just to accidentally lose it.
1. Describe the Problem Reference: Ticket - 17606227 Article - CS433748 We are trying to use the SEARCH tool to find features that do NOT belong to a specific layer. The issue is that if the layer doesn't exist, the search results come back empty. It should be the exact opposite! In other words, if there are 20 features in a model, and I want to find all features not on layer TEST, and there is no layer TEST then all 20 features should be shown! We have our library models have some layers that other design models don't and we would like this logic to work across all of our parts, but they don't. 2. Are you using a workaround?NO3. What is the use case for your organization?We are trying to use a mapkey to select specific features for an automation that creates and shows dimensions in a drawing.4. What impact does this problem currently have on your organization?We won't be able to leverage the power of the mapkey automation, which will cost us time and money, doi
1. Describe your environment: What is your industry? What is your role in your organization? Describe your stakeholders.Company: Manufacturer of hydraulic components for hydrostatic transmissions.2. What version of Creo Parametric are you currently running?8.0.9.03. Describe the problem you are trying to solve. Please include detailed documentation such as screenshots, images or video.This product idea is a response to PTC case C17596679 (Case Details: 17596679 (ptc.com))An option will be good in Creo drawing for avoid to apply a scale during a copy of a sheet in a different format from the one define at the drawing's creation. Currently when we copy a sheet with a format different than the one define at the drawing's creation, it is applied a scale (ratio between the 2 formats) to the copied's sheet.4. Are you using a workaround?We change the format of the sheet to copy to the format define at the creation of the drawing.5. What is the use case for your organization?We create for
1. Describe the ProblemIn the model tree graphics area, you can add folders as shortcuts in the Common folders area.This allows you to click on the folder and Creo jumps to that location. But to work in this location you still need to set the working directory to this location. It would be handy if you could right click on the common folder that you've added, and select set working directory.2. Are you using a workaround?The current workaround is to click on the saved folder shortcut in the Common folders window. Then it will show the contents of the folder in the browser window. Then you need to go up back one folder level by selecting the one level higher folder name that is shown in the address bar at the top of the imbeded browser. This will then show your saved folder name in the embeded browser. You can then right click on the folder in the imbeded browser and select working directory for your saved common folder name.3. What is the use case for your organization?This will b
1. Describe the ProblemAfter using Creo 11 performance report, it occurs to me that there is no force full regeneration function. Doing a full regeneration is really important to investigate hidden errors and problems in models. This is evident when using the new reporting tool compute which I’ve been using on models to find serous errors that otherwise are hidden from uses with the part hasn’t changed since last regeneration caching. This hides problems. 2. Are you using a workaround?None, but there are some odd techniques to force a full regeneration but no direct action. I’m forced to use creo 11.3. What is the use case for your organization?The use case for the enhancement you suggested revolves around model integrity and error detection. Specifically: - Improved Debugging: A “force full regeneration” feature would allow users to identify and address hidden errors or issues in models that might otherwise go unnoticed due to caching or other optimization mechanisms. - Enhanced
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.