Recently active
Current Creo/Simulate cannot perform a valid buckling analysis on a structure that has thermally induced contractions and/or expansions applied to it via "temperature loads". My industry (rockets) and surely many others would get much more valid buckling results if we didn't need to artificially remove this stresses from our analyses.
The current Creo/Simulate is unable to perform buckling analysis on pressurized structures. Every rocket and airplane uses pressure stabilization in order to dramatically increase vehicle stiffness without the need to "add solid mass". The lack of this ability is a huge hole in PTCs Simulate offereing as it is THE major strength analysis that all of aerospace needs for primary structural load paths.My understanding is that other codes accomplish this by defining the pressure as a pre-load somehow.4/14/2015- Everyone at my company is now being asked to use NX for all future development. I have learned enough about NX NASTRAN to confirm that for buckling analysis, pressure is entered as a pre-load. Creo really, really, is at a disadvantage in many mega-aerospace companies without this ability.
Optimizations are often necessarily based on user-defined measures such as: von_mises_of_shell1<64000 lb/in^2.In today's Creo Simulate, any small edge or point that has a singularity, negates the ability to use optimization because the measure is looking at the maximum... and that maximum is at a singularity (with bogus stress values).If a user selects such an edge or point to be "excluded", then measures including those excluded features should also ignore their values. In other words, if I am optimizing a shell thickness so that the shell's von mises does not exceed 64000 psi, and I have already "told Creo" to exclude certain junk locations, then I want the measure to be monitoring all locations of the shell EXCEPT for the excluded geometry.
This "idea" can be removed. It turns out that there already IS a built in report that does exactly what the original text in this product idea requested.
It could be useful to have same functionality for preview intersection parts in Assembly Feature, like in new Creo 2.0 sections.(I need this functionality for preparing geometry for render. Section cannot be used for render now)
Currently, the File tab allows you to select a previously opened file to work on. A very useful addition would be to allow the selection of a previously used Working Directory. Our company uses a complicated directory structure for storage of customer files. Working over the course of the day on a number of different projects requires constant traversal up and down multi-branched directory trees. Having these directories available as a "one click" selection would be much more efficient.
It's so infuriating to work in piping and not be able to use the piping centerline for other features. It looks like a curve, but cannot be selected for creating anything.PTC please allow the piping centerlines to behave like a curve.
In some analysis dialogs (global interference, pairs interference and mass properties for sure, maybe others), the user is presented with three active buttons, glasses, a green check mark and a red X.The green check mark would imply 'Go', but what it actually does is run the selected analysis and then immediately exit the dialog without allowing the user to view the results. If the user would like to see the results (why wouldn't they?), they should select the 'glasses' icon instead. Additionally, if the analysis has already been run, clicking the green check runs it again before exiting. If the analysis is time consuming, the user must wait again for it to run before moving on with their work.The functionality of the green check mark should be revised to eliminate confusion. Some alternatives:Disable access to the green check mark until an analysis has been run. The user would be presented with the glasses (run the analysis) or the red X (exit without run
In 3D Annotations, allow a datum flag to correctly "hang" off of the GD&T box like in a 2D drawing.Here is what it correctly looks like in 2D:Here is what it incorrectly looks like in 3D:Regarding the location of the datum flag in general, there does not appear to be a way to where it ends up in a 3D Annotation. See below where the datum flag would normally be attached to the leader line:
It is very easy to create cloud over some part of drawing for highlighting purpose in 2D software like Auto cad & microstation.But in pro/E it is very time consuming.Only way to use Arc and join them one by one. But if in the place of this if Pro/E is having line style like arc it can be achive very easily.
Englisch: When i add a drawing to a part of an assembly i have to update the assembly drawing. But this should only be the case if the model has also experienced a technical change (ex.: Chamfer added). Have I only add a drawing to the part the assembly drawing should not need an update. This is recognized in annotation: Add drawing to part -----> assembly drawing need an update and in Annotation is blue ( force update ) Add drawing to part with technical change -----> assembly drawing need an update and in Annotation is cyan ( normal update ) Deutsch: Keine Aktualisierung für die Baugruppenzeichnung wenn man einem Teil der Baugruppe eine Zeichnung hinzu fügt ohne technische Änderung des Modells. Füge ich einem Einzelteil einer Baugruppe eine Zeichnung hinzu so muss die Baugruppenzeichnung aktualisiert werden. Dies sollte aber nur der Fall sein, wenn das Modell auch eine technische Änderung erfahren hat
Actually the X, Y and Z sections are not working with the first Csys if it's not a default Csys.Add a detection in order to select the X Y and Z axis of the first Csys found in model Tree.
While in the creating views mode, if you click on the show planes icon or if you change from solid to wireframe (or vice versa) you are exited from creating the view. This shouldn't cancel the command. Or if there's some internal conflict in the software, activating the create views should turn on the plane automatically. Thanks, Dale
We should be able to create a spot weld on a surface explicietly, reference to a curve ,edge, surface, planes, axis, points. Spot should also be created by following a curve and able to pattern it as well.A report should be generated of the spots distances (X,Y,Z) from the respective reference and should be editable.distance between two spots should be given and should also be edited.
We should be able to create a Two Panel spot weld and Three panel spot weld with respect to a co-ordinate system or with respect to a edge or surface. We should be able to define all the Fastener Process Category (Welding, Adhesive, Seleants , Unspecified ) and spot represenatation
PDMlink choose configurations like this when doing a add to ws:B.2 LatestB.1 As StoredA.2 LatestA.1 As StoredI would like to get it to work as this:B.2 LatestB.1 As StoredA.2 As StoredA.1 As StoredFrom Tech support:There are two types of LATEST:1. LATEST_LATEST: Latest iteration of latest revision2. LATEST: Latest iteration of current revisionAdd To Workspace determines the use of As Stored if the initially selected (iteration to be added to the Workspace) is an iteration prior to the LATEST of the revision (2. above), not the revision/iteration that is prior to LATEST_LATEST (1. above).I agree with you that it could be useful to have the default behavior to use the Latest configuration for LATEST_LATEST only, or to have a preference to control this.
We want Spot welding to be user freindly.we should be able to apply spot on the fly where ever we click on the surface.With respect to a co-ordinate system it should we give the details of the spot (X,Y,Z details)
Support nVidia 3D Vision (or other equivalent from other manufacturer) for simulated 3D effects display on 3D capable displays.
As a product designer, I do a lot of trade studies to compare various options, or compare one design in the various states it can take. Oftentimes, I need to collaborate with someone else, who may look over my shoulder at my Creo Parametric screen. To understand the differences between options or states, you often want to do "A - B studies". Do you like "this" or "that"? So, you may wish to switch back and forth from one simp rep to another quickly, to highlight the changes. Or turn a section cut on and off. Or, do a "poor man's animation", by setting a relation such as "X = X+1", so a dimension grows slightly with each regen.In these cases, the ability to visualize the changes is severely hampered because Creo Parametric automatically refits the view when you regen, when you switch simp reps, and when you turn a section on or off. You really just want to see what changed in the model, without the model moving across the screen, or the zoom lev
2 Item's must be changed in future Release for DXFDWG / SVG-Konverter- the Conf-File must be separated because DXFDWG and SVG using different Values for example Font-inclusion. In dxf-Conf I need the filename (finding in the font-folder of Windows) for the specified font In svg-Conf I need the name of the font (showed p.e. in Adobe Illustrator). This meens, I have to copy the Conf-File but in- WIN7 it isn't allowed for a user to modify / overwrite files in the program-path. So it must be possible to search the conf-file first in a folder which is accessible for everyone. Maybe there is an undocumented environment-variable DXFConfDir available?
If you create a face set feature you cannot copy it to another part without using the copy faces function, when you use custom features you can select a face on any part to create it, it would be good to be able to do the same when copying user defined features. It would be even better if you could save a new feature to then create commonly used ones from the custom feature table.
If a feature (extrude,revolve,etc) is made from an existing sketch, there is no access to that sketch from the feature's dashboard. The only options are to either unlink the sketch to redefine it or to cancel the feature redefine (and possibly loose any changes made) and then go back to redefine the sketch.A mechanism for redefining external sketches would be beneficial.
図面モードにて、寸法プロパティを修正すると、引出線の上側には1行しか記入できません。これを、引出線の上側に複数行入力できるようにしてください。なお、注記で作成すると、下記のように”@o”を入力して改行すると引き出し線の上側に複数行を表示できます。寸法プロパティでは同じように入力することができません。『φ6深さ15後φ8.2深座ぐり深さ3@o(注記2.)』
I would like to set up a weld preference for tack welds. We have a standard that defines the number of tack welds along a joint based on the length of the joint. Unfortunately, the interface where we define the variable called 'Number of Welds' in the Weld Preferences menu only accepts an integer in that field. Rather than hard-coding in some value that will almost certainly need to be calculated & modified later, why not have that happen automatically by entering a relation that refers to the weld joint parameter LENGTH, performs some function on it, then rounds it up to thge next highest integer, something like CEIL(function of LENGTH). By automating this, you could not only eliminate the need to manually calculate & enter the number of welds, but you could also easily ensure some level of consistency in the definition of tack welds by making that preference available to all users at a facility.
COM & .NET API of Cocreate Modeling are able to connect to a specific version of the application but not to a specific instance opened. If there are many instances running it connects to the first opened. Code example: Sub ConnectToOsdmServer() Dim OsdmApp As CoCreate_OsdmObjects.IApplication Set OsdmApp = CreateObject("CoCreate.OsdmServer") OsdmApp.LoadFile("c:/temp/foo.pkg") End Sub Then I would like to have API to manage multiple instance of SolidDesigner.exe running. Windchill Workgroup Manager is able to do this.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.