Recently active
Hello,for better visibility which window is currently active it would be an advantage to highlight the current active window instead of only writing it in the title bar.I imagine a different color of the ribbon interface or a different background color in the graphics area.It should be visible even if you don't look directly on the screen.Best RegardsJens Wagner
It is currently not possible to inquire brackets of existing dimensions. For purposes of quality control, it is necessary to inquire brackets of existing dimensions. Application in Germany: Erstmusterprüfbericht
ability to measure mass properties in units other than set units.for example : if the units is set to MMNS, i would like to measure in cm,grams...without changing the set unit.at present i can only measure mass properties in other units other than the set unit after changing the unit.which some times results in failures and also it is time consuming.
we work for a medical equipment company.we regularly work with sketches which have to be wrapped around a cylindrical part.the wrapped sketches need to solid filled.at present the "wrap" option does not have the abiltiy to fill the wrapped sketches, and a considerable time is wasted in filling each wrapped sketch manually in the detailing mode.
Create different icons for shading, with transparency on or off.
When adding creation and change of a wire, I expect that the input of arbitrary diameters or a color can perform. I would like to use the wire which sometimes is not registered.
Stop the Belt Master Level Ups from being shown on the discussion board.It's a waste of space and hides the true issues that people are posting.Has is been mentioned that when these things show up on the discussion board, people looking for true answers to issues lose their ideas behind the "wave" of posts?
3D symbols (default from pallette or custom) created in a model can only be show in one drawing view at a time (similar to dimensions). This can cause problems if the symbol contains important information. One example might be if a drawing shows a front view and a iso view where the symbol should be seen in both views.The current workaround being used is to create multiple instances of the same 3D symbol (one for each veiw in the drawing where it needs to show up) on top of each other in trhe model. Weak...but it works OK.
In Creo5 this color was cyanIn Creo2 this color is pink.
When we select Transparent Overlay In Simulate results, the scaling in percent is automatically ativate.And the problem is we never used a scaling in 1 percent, always scale 1.So be able to choose if we want automatically the scaling in percent or not.
(中文测试)本意见仅用于中文测试。
I want to add another shape's into primitive shapes when using freestyle.When We design, maybe there are two cases.One case is that shapes be created by simple primitive shapes. Two case is that shapes be created by existing shapes.I think freestyle is best tool for design than now, if existing shapes be added into freestyle's primitive shapes.
this option would make alot easier to be able create a note using the on item to have an option to align note with selected item
Would be great if there was an option in text style the you can mask the background of the note, so it removes all lines ect under the note.this would make reading the note much easier
Current nonisotropic material definition does not allow for the definition of temperature-dependent functions as properties. This makes it very difficult to model nonistropic composites (such as G-10) which are used across broad (often cryogenic) temperature ranges.
When inserting a general view, if the (primary) view is named the same as the view's drawing model, the sheet number and sheet name (and maybe even the view coords) would be passed back to the instance of the drawing model within the drawing. This way a BOM table could automatically show the drawing sheet information (sheet number and/or sheet name of a multi-sheet drawing) for each line item in the BOM and parametrically update for sheet additions/deletions and view moves. Perhaps a selection (toggle or check) when creating/editing a view of a part or assembly to enable it to be identified by the sheet number and/or sheet name when the item is listed in a BOM.
Table Restricted Values can be a powerful tool and a great time-saver. Tables for restricted values are dificult to implement without considerable trial-and-error, are syntax critical, and are difficult to edit. A Restricted Values File Editor that properly parses entries and manages the context of the file would make the use of this potentially powerful feature much more efficient and practical to implement. Easily controling ranges and extents of data is the first step in uniformity and quality control.
Currently, coordinate systems are impossible to select unless you pick directly on some mysterious, unknown sweet spot.Please make coordinate systems easier to pick by increasing the area for this elusive sweet spot or providing a window selection, which would actually enhance many other selection operations as well.
When creating a foreshortened radius dimension in accordance with ASME Y14.5, the dimensions locating the center of the radius that have been foreshortened should have the "Z" shape dimension line also. Wildfire 5 added the ability to create the Z-radius, the functionallity needs to be updated to automatically cerate a Z-linear dimension for the appropriate dimensions also.
There should be a standard way to reset all View Manager states. These should be built into Creo and non-editable.They should all be consistent in their offering.For example: Simp rep has "Master Rep" which will clear all simplified reps.Orientation has "Standard Orientation" and a modifyable "Default orientation"Sections have "No Cross Section"Style has "Master Style"The following need resetable states as well: Combined states (has default all, but not master all - rep callouts are still displayed on the window and layer state remains because there is no default or master layer state)Layer StateExploded view (has the checkmark to reset, but should have a "no eploded view" as well for consistency)The default or master layer state should refer to the "save status" layer state. If you are in a layer state "save status" will save to your default and "save..." will save to the layer state. So layer states could get accidentally saved over your default layer state.
I would like to crete Trajectory Rib feature for open geometry - at this moment it is only possible create this feature for closed boundary - see discusion hereRegards,Vladimir
In aerospace "skin & stringer" structures, the lightest mass structures may want to allow the skins to buckle... but not the stringers. The current optimization capabilities only recognize a single, system provided "buckling load factor" which applies to the structure as a whole.RequestProvide some kind of ability to allow (ignore) buckling of some items but not others. I'm not sure of the best way to implement that. Perhaps allow "BLF measures" to be assigned to specific components or simulation features in exactly the same way as one can measure/monitor stress. In effect, allow a criteria like "optimize the stringer dimensions for the lowest mass that keeps the BLF of the stringers >1.5. Such an analysis would effectively "not care" if the skins were (or were not) buckling.
Below is sample of required functionality.
EDIT: I hereby withdraw this product idea, as I have finally been able to clean up the layers in our manikin library myself. I describe the procedure in full detail here (there's quite a bit to it, as there are a few of the built in layers that you need to keep to maintain expected functionality).I'm not entirely sure why I wasn't able to do this before, but it's likely one of two reasons:PTC quietly changed the read only status of these types of models in the latest version of CreoThe system I was using at the time ignored the revised versions of the models I saved (*.prt.2 & *.asm.2), and instead continued to open the original versions (*.prt & *.asm) making it seem that the saves were ineffective.Probably the latter; sometimes I'm just an idiot.New Product idea would be for PTC to incorporate some of my layering fixes out-of-the-box. In particular, making sure that all the coordinate systems that are on the MANIKIN_DRAG layer are not also on any other layer
Neither of the above functions have ever worked (over 20 years now!) when defining simplified reps and zones because they are based on each component's "bounding box" and that bounding box currently includes any copied geometry, construction features, distant (from the solids) coordinate systems, etc. So, the right rear tire of a car assembly ACTUALLY fits in a "bounding box" of perhaps 26x26x10 inches (tire diameter by tire width). HOWEVER, if, as is often the case, it has a floating coordinate system representing the origin of the car (let's say the middle of the front axle) then Creo assigns a bounding box of ~10feet x ~5feet x 26inches because that includes this floating coordinate system!If I then define a simplified rep to just show me the front axle area. ALL components (from front bumper to rear bumper) that have a "car origin" coordinate system display.This entire mess could be entirely fixed (at great advantage to drawing, and retrievals that currently cannot use size a
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.