Recently active
When we select, we may select part, component, surface, curve etc. We can filter as from the bottom filter. However, the filter need to set every time. I suggest if pressing a functional key could have alter the selection filter that would be great. For example, f2+ mouse click to select surface, f3+ mouse click to select part etc...Regards,Jayanta Sarkar
Same part in an assy drawing assembled multiple times. Create assy section view in drawing. Want to make the xhatching the exact same for the same part everywhere it is used. Currently this must be done manually, but there should be a way to state or copy (or a rule) to make the exact same part have the exact same xhatching everywhere it is used in the assembly so that they all show the same in the drawing cross section view. THIS WOULD BE A HUGE TIME SAVER.
There is currently no way to programmatically set the orientation of a ProUISeparator. The only way to set the orientation is through the use of resource files. Please create a function similar to "ProUISeparatorOrientationSet()" (and potentially a paired "ProUISeparatorOrientationGet()" function) to allow users to set this value in their code.
Please add functionality to show or hide the combined states at the bottom of the Creo window (something along the lines of "ProCombstateTabHide" and "ProCombstateTabShow"). This is needed since ProModelitemHide returns a PRO_TK_INVALID_TYPE when operating on a type of PRO_COMBINED_STATE, so another solution would be to simply adding support for that function instead.
Hello,When I want to investigate a specific part in an assembly model, I select the part, then click on the 'ONE' icon. The selected part is then highlighted in the model tree. Even if the sub-assembly in which the part is located had been minimised, the 'ONE' icon expands it so the selected part is visible. That all works, unless I activate the sub-assembly first. Then, the 'ONE' icon apparently does absolutely nothing.This idea is to make the 'ONE' icon work regardless of what is already selected in the Model Tree.Shoot me down if this already happens in Creo x, but it works (doesn't work?) the way I described in WF4, M220.John
Go back to old functionality to be able to add different image/texture on both side of the same surface/quilt.It was able like that in WF, but at the Creo if we wish to have different view from front view and something else from back view we must use two different surfaces...
The possibility to edit the whole Nested Family table in Excel:Currently it is only possible to edit the Top level of a nested family table in Excel. The instances of the Top level have to then be individually opened and edited in Excel seperatelyThis means it takes lot of time to create/update library items that uses nested family tables.
Functions exist to create, delete, rename, and even to "display" an Xsec, however there is no function to "activate" a cross section. Please add this functionality.
Please add functionality to restore "automatic sorting" combined-state tabs. As of right now, tabs are automatically sorted alphanumerically until they are manually moved. Once any one of the tabs is relocated, it completely breaks the automatic reordering scheme, and now all future combined states must forever be manually sorted for that model. Please add functionality (potentially in the View Manager?) to reoder the combined-states as appropriate, possibly with an option to "Sort by Name" set by default, so that automatic sorting can be re-enabled.
Most of my design time I use boundary blend to close some surface gaps like in this example and will be nice to have ability to have predefined feature like Boundary Blend when the boundaries condition as default will be set to tangent (can be also another one for curvature or normal but as e.g. different icon under BB icon). This can be solved similar like we have with Round, chamfer, draft or Rib - where we chave options of choice shown by triangle.Creo here should try to set at pointed deges tangency to default surfaces nothing more - if user need to set it free or curvature or even normal still should be able to do it, but the benefit is that user will win a lot of the time as it is at the moment when we must spend another time to choose the condition from the list...Also simple rule can be here - if default condition e.g. on 3D spline not exist - this confition will be set to "free" - isn't it simple?
I wish to have influence to change the default direction of the loop path in sweep, because it is alwais oposite It can work also better if Creo maintain the same direction as it is on preview with only the first edge selected - because it is generelly correct!First selected edge:I see also that the source of the problem is because start point is in other place:I recommend to maintain the start point as it was the start during first edge selection!Then result will be ok! This improvement will help to not flip direction almost every time, so the work will give more pleasure Sometimes plaing with direction to obtain right position on the path is much harder in comparison to this example - when the pathe edge is solid not a surface Creo can catch side surfaces as reference instead face surface etc.
to improve shrinkwarp - to Associative shrinkwrap with associative mass properties
Replace more than one face with a quilt
to add the ability to have a hole on an inner cylindrical face :
Allow using portions of a sketch for feature creation. For example, extrude:
Add adaptive, graphical, popup menus for common comands.
Add "select group" option: select a feature, then select the group (similar to select parent in assembly)
To enable alphabetical order for File Open/Save.this is to allow easy selection
Allow isolation of a datum (plane, axis, etc.) directly without thetedious use of layers:
Fast highlight for component selection in assembly (a bounding box or shaded selection) instead of full geometry.Today when you have complex assembly with complex parts ( many surfaces ) highlight is time consuming.
Default selection will be on the closet element to the user, forexample, while hovering and/or pointing over a geometry the closest face will be selected and not the underlying edge.
to allow smooth selection of those basic entities ANYTIME. ANYWHERE.as of today there is inconsistensy in method of selection and availability of option.
The ability to copy a view in a drawing, keeping all the drawing view properties the same.I frequently have to create multiple partial section views of a large assembly. All the views are oriented exactly the same, the only difference is that they each reference a different cross section, and sometimes a different origin and spline for the partial views. Current workaround is that you have to add a general view or projected view, orient it properly. Change its properties to partial view, apply, do the whole ref point & spline thing, apply, change the scale, apply, set the cross section, apply...etc.A huge time saver would be if you could just make an exact copy of the view, and then you only have to ref a different cross section, and/or ref point for the partial view, and you are done.
In the normal mode of creo it's the drop-down menu for the right click. If you use freestyle mode i saw that it's a quick selection wheel (same as solidworks)and i think it's a pretty good feature. If it's develop why PTC don't put this everywhere.like this one:
As of right now, there is VERY limitied capability for a ProCompdisplay relative to the rest of the elements of a ProCombstate. Please create the following functions: ProCompdisplayCreate ProCompdisplayRemove Also, since a styleState operates similar to a layerState/simpRep in the respect that it must be able to touch components beneath it... there may be a requirement to add something similar to a ProCompdispdata structure, so that the style can be applied for individual components in the assembly. This would raise the need for a set of ProCompdispdata functions as well to add/remove components and their desired states as desired.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.