Recently active
The model check results page has three sections, divided horizontally. Let us resize those sections by dragging the dividers! (See attached image) The parameter spell checker (shown in the attached image) uses such a small size for the parameter list, you have to scroll to see more than 11 characters. Resize it to fit, and let us resize it if we want to! The parameter spell checker narrows the value column so far that the word wrap causes the parameter and value to be misaligned. Resize it to fit, align it, and let us resize it if we want to! I'm sure I could find plenty of other places where this problem occurs in modelcheck, so make the change across the board.
Hello, When working with Creo Simulate 4.0, if a reference is created inside of it (for example a datum point, plane, etc...), they are all stored in the group "simulation features" : If this features are needed in modeling, they need to be promoted via right clic : Unfortunatly its not possible to promote multiple references at once Can you enable this in feature update of Creo Parametric 4.0? Thanks in advance
In a drawing, when you create Ordinate dimensioning, sometimes the edge/feature that is selected for the baseline dimension loses its connection. When that happens, you cannot “Edit Attach…” and relink the ordinate baseline to that edge/feature. As a result, your only option is to delete the baseline ordinate and as a result, ALL of the offset dimensions that reference that baseline are then deleted. This can cause a significant delay in producing a revised drawing. I’ve lost as much as an hour, dimensioning a drawing that only lost it’s baseline dimension. For the secondary dimensions that reference the baseline, this functionality works. This also would be beneficial in case an engineering/draftsman realizes he/she has selected the wrong feature for ordinate dimensions. If he/she had finished dimensioning the drawing or had that pointed out in a review, what should be a 10 second fix turns into an ordeal.
Hello, It would be great to be able to add a shaded view with Perspective in a Drawing. 2 SPR talk about this limitation in Creo Parametric : 2859727 / 2204024 It's actually the case in Creo 4.0 M020 SolidWorks allows this functionality Thanks Nicolas
Enable the export of the Sequence's to 3D PDF. Currently it is only possible to export an "Animation". It would be good if it was possbile to go through the Sequence Steps using a PDF reader, since this is a common installed tool (Creo View isn't and Admin rights are needed for installation.)
As a designer / planner, I want the drawing sheets to be named according to the FuBIT tables present thereon:e.g. Edit pages 1-21 to find the tables more easily. IST: currently the drawing sheets can only be named continuously with Toolkit.zB. Sheet6, Sheet7 Set: The sheets are named using the tables shownCase: C12460571Answer from PTC: Contacted Andrea and informed her that we do not have Pro/TOOLKIT functionality to name or rename the drawing sheets. We can get the name with ProDrawingSheetNameGet(), but we don't have a corresponding function ProDrawingSheetNameSet() or any other means to set the name. As always, one may try with macro functionality used by the application.
Referring to article CS245178: https://support.ptc.com/appserver/cs/view/solution.jsp?n=CS245178&language=en&posno=1&q=ifx%20two%20nuts&ProductFamily=Creo%20%26%20Pro%2FENGINEER%7CCreo%20Simulate%20%26%20Pro%2FMechanica&source=search&source=Sitecore%20Article%20Viewer It would be a great innovation to be able to add a secondary nut in IFX to act as a lock nut. This is a common practice in many structural industries.
The layer rules are a powerful function to optimize Creo models and the data quality within these models. We use layer rules in our standard templates to ensure, that every user can handle every model. Other user layers are allowed but they are not needed to control the visibility in our models and assemblies. This ensures better interaction between different designers and stable data exchange and data conversion processes. Today PTC provides toolkit functions to read and create layers, layer rules and to control layer visibility. We are able to check these contents with modelcheck and we can provide an automated repair function. All subsequent process assumes that all features are placed on the right layers by using the layer rules. The possibility to ignore the layer rules by including or excluding features manually is a significant quality gap for us, because we cannot check it with toolkit. Sometimes features are accidently added to our standard layers and it costs much effo
It would be nice if there was a checkbox in the Configuration Editor to turn on/off all config.pro options so you could troubleshoot if the config.pro was causing an unexpected behavior. I understand you can restart Creo without the config.pro set but it is a pain to restart sometimes. I also understand that this idea would be hard to impliment because some options can't really be turned on and off (like switching the graphics setting).
When someone has used the wrong model in an assembly you can easily switch it out by creating an interchange assembly. When someone has used the wrong model in a drawing view I just checked today using Creo 3 and you cannot switch out by an interchange (only current family table members).
Hello, We would see appear the capability to extract grid point force and grid point moment for each node location (GPF/GPM) into Simulate. The ability to extract nodal force and moment exist in all commercial FEA software (Abaqus, Ansys, Nastran, Samcef). We would see this functionality appear in a near future into PTC/Simulate. Let us know your position. Regards,
We should have to ability to filter and sort Creo Ideas by date and resolution. Someone sead that some of these ideas are under consideration. Where can I go to see the ones that are under consideration? I'd like to vote up or down on the consideration and give my opinion on ideas that are important to me. Some of the older ideas or the ones that do not affect my current software I do not want to see. Why even have Wildfire 4.0 ideas? Are they really going to add or remove functionality in a patch. They should be removed and given a reason for removal. Old ideas that are rejected should still be searchable so that we know why the ideas are rejected and won't be implemented in any new versions.
Enhance the cell drop list to display the part component instance name (Selected component). Avoid to: Highlight the cell and from the upper pull down menus select Tools / Replace Using / Family Member, and then only choose in the list.
When exporting a deformed surface from Creo Simulate as a VRML file, there are only 6 significant figures for each point in the cloud that is generated. When the significant figures move to the left side of the decimal place, the accuracy of the points decreased dramatically. There should be a config option that allows you to increase the number of significant figures when exporting a VRML file from Creo Simulate.
It's very anoying and time expensive for users to change icon sizes in Creo UI. Currently users can do this by using the function "Customize the Ribbon" and "Modify" each single function but as Iwrote before it's to time expensive to do this. It would be helpful to get an config.pro option to change the icon sizes from ui from small to large or medium or vise versa.
In one example of sweep alongside a curve material that would be removed if the sweep would be shorter are later on recreated again. There should be a option to say to remove all material that have been hit by the sweep feature:
When loading assemblies from Model Manager or from PKG format, Creo Elements Direct Modeling stops loading if EMPTY or CORRUPTED files are inside assembly structure. It can be useful if CEDModeling should continue to load all other parts and subassemblies giving a warning message insted of stop. This is standard behavior in Creo Parametric or 3D Cads in general.
Article - CS160646 Performance issue with Creo Parametric 2.0 during STEP import with confusing warning message "Creo not responding" PTC R&D said, The message 'Creo not repsonding' is a long-standing message. If Creo cannot respond because it is doing work/computations. So, I hope the Creo UI will be improved so I can see the progress. Thank you.
I would like to have an option in Creo to create family tables in a Mirrored part by keeping dependency with parent part.I have a design with Right hand Side & Left hand side which are same in geometry but mirror sides. Also I have family tables of both design with different height of one feature. So I designed Right hand side part first with family table instances. Now I have 2 options in creating Mirrored part. 1. with features & 2. with out features. With 1st option I can maintain Parent & child relation so that I can keep both parts RH & LH at a single shot by updating first designed RH part. But in this way I can not create Family Table instances for LH part since it doesnt have features. With 2nd option I can create Family Table instance since it have features, however I cant keep parent & child relation between RH & LH parts. So my request to PTC is to create an option for creating Mirrored parts with features along with ma
would it be nice to have the possibility to have CENTER in the shortcut menu when you put a dimension
Currently in Creo 4.0 M020 you are unable to controll Dual Dimensions and Ordinate/Linear properties in part mode
It is important during construction to have the possibility to convert a hole that has been created with the drilling tool into a thread or vice versa. It is often not clear at the beginning of construction which type of drilling is needed at the end.Deleting and re-creating is very time-consuming and complicated, because it may already have been referenced to this design element.
It is important during construction to have the possibility to convert a hole that has been created with the drilling tool into a thread or vice versa. It is often not clear at the beginning of construction which type of drilling is needed at the end.Deleting and re-creating is very time-consuming and complicated, because it may already have been referenced to this design element.
Customer requests rendering information is published whenever publishing AR. To do design review as mock up, rendering information is necessary. Information such as Material, Color, Texture and Shadow has to be reflected.
I want one common baseline for each direction, so I don’t have multiple baselines. The dimension 0.0 needs to be able to be shown in each view where it applies. Currently in Creo 4.0 M030 and before managing ordinate dimensions can be a mess. If you previously had ordinate dimensions in the drawing but now are suppressed and the baseline was deleted. When changing new features dimensions to ordinate a new baseline will be created, even if one currently exists.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.