Recently active
under a view there always appears a label. there is a default setting that says 'No Label' and then the text is not displayed, but there always remains a vertex.to get rid of this vertex, i use the hide command.it would be great if there would be an extra option in the default settings to set these view labels hidden by default.
In Creo Elements/Direct Modeling it is possible to use the tab key to change the context when selecting items between only the objects that are completely within the box and objects that are completely or partially within the box.In Creo Elements/Direct 3D Access the tab key does not have this functionality.As 3D Access is generally used by persons with a limited command of the program, it is not acceptable to expect them to change the context in the settings menu before performing the selection (and then resetting it again afterwards!).The tab key should receive the same functionality that it has in Modeling.
Several tongues at a sheet metal already bent are to be created. The mitres for the tongues are created automatically. (see picture, red lines) Kind regards amIn deutsch: Es sollen von einem gebogenen Teil automatisch die Laschen erstellt werden. Die Gehrungen sollten wie im Bild bei den roten Strichen erfolgen. Die Abstände bei den Gehrungen sollten kleinstmöglich sein. Gruss am
Would like the ability to copy a used defined custom feature to other parts. Current workaround is to copy & paste the faces and then redefine the feature.
ProMechModel is Creo Simulate geometry model which is used for CAE simulation.Hence I expect edge should be created where two surfaces interferes. This will help us to create conforming mesh across edge where two surfaces interferes if edge gets created. In other words mesh will preserve that edge. I have attachedwhere bolt surface interferes with plate surface and edge do not get created where interference occur.
I should be good (both time and mistake reductions) to get automatically the M16 annotation symbol in stead of the diameter 16 symbol when pushing "Show Model Annotations" in the drawing for the hole with thread. Please see model, drawing and print screens in the zip.
We would like to apply a thread the full length of a bar. Current Machine features do not seem to allow this? The bar can be threaded and milled to remove material, but this invalidates the feature.
When API ProMechmodelGet fails to create ProMechModel from ProSolid model then it just return general error. It is difficult to get any additional information about issues in ProSolid or native CAD model. It is very much helpful and desirable if this API returns additional information about an error like pointing to items in assembly because of which ProMechModel creation has been failed.
Add repeat region family table function with the prt simplified representation to replace Family Tables with prt simplified representation
Creo should remember the units that the first default constraint item has eg. mm and then when a component is being added Creo should flag up a message saying that this model is not the same units, do you want to change it? This would stop many problems including the datum planes going gigantic.
Allow feature redefine in drawing mode. Why open a new window for the part to redefine a feature? Use case: just want to drag a geometry element in a sketch to a new location. I don't really care about the accuracy of the location just somewhere that looks good in the drawing. Currently either have to open part & redefine feature or calculate new dimension values, edit the values in drawing & regenerate the model.
In creating a chamfered hole for a flat head screw, I set the diameter of the chamfer, then I noted that it was a free fit not a close fit thru hole. When I switched this, the diameter of the chamfer changed. Since I had already changed this away from the default value, it shouldn't have updated, but stayed the same.Changed the diameter of the chamfer.Changed from close fit to free fit and the diameter of the chamfer changes back to .507.Remember to change the diameter of the chamfer that had been already set.Thanks, Dale
Currently there is no means by which to save lengthy data (which includes carriage returns for formatting) as a Note type parameter in a drawing.I understand there is a workaround for pointing a drawing parameter to a model note, but this sort of rigging is not straightforward and is a lot of extra work.My company uses three CAD programs in addition to Creo, which can all do this, but not Creo....yet.We want to use the Note file attribute type for lengthy material, finish and process requirements specified on the drawing (which often have a long list of alternates and/or processing steps) so that we do not have to change the model also if/when these requirements change.
Setting hidden config.pro option Trochoid_Milling yes can enable Trochoid option in 3 axis trajectory milling only. Please add new one single milling for Trochoidal in Creo ParametricAbout Trochoidal Milling, please refer to Trochoidal Milling - GARANT TPC Mills | Hoffmann Group for detail
helloHave the ability to adjust the width of the first column with a default value
In an annotation view it is possible to make all hidden lines either visible or invisible.However, it is currently not possible to make all the hidden lines that are not within a cutaway visible and at the same time all the hidden lines that are within a cutaway invisible.Workarounds:- individually make unwanted hidden lines invisible- make a separate partial view covering the area of the cutaway and define all hidden lines to be invisible in this view
'Gradient Background' color setting has no effect on the Preview in File->Open, i.e. background color of the preview gets its defaults from the syscol.scl file or system_background_color option in config.pro, BUT it is not possible to set the background as blended Gradient.In Wildfire versions of Pro/E (like Wildfire 5.0) the Gradient Background option controlled both - The main Graphic Window + the Preview Window,but in CREO 3.0 the Gradient Background option controls only the Graphic Window.Most of Pro/E users that I know prefer drafting drawings with a black background.Setting this Black background option, undesirably affects the background of the PREVIEW window - to be BLACK!It is most needed to have the Gradient Background color setting to control also the PREVIEW Window!
The Question is: How to control the length of the centreline for half section in Pro/ENGINEER, Creo Elements/Pro and Creo Parametric New drawing setup option half_section_line allows to set centreline but its length cannot be changedHow to control the length of the centreline for a half section view?Possible workaround to extend the display is to show or create a centreline and move its drag handles as desired
We often have a need to dimension a drawing with both US/Imperial and Metric dimensions. We don't want "dual" dimensions but rather the ability to display a particular dimension in a different unit than the rest of the drawing. As stated in a similar request, it is relatively common to need a metric sized or threaded hole or other features in a normally English dimensioned drawing.
Upgrade support .ai import file version from 7.0 to 15.07.0 is a little old no ?
It is possible to wrap a spline curve that is on a work plane onto a cylindrical surface using the function "Wrap on Surf".However, it is currently not possible to go the other way and to wrap a spline curve that lies on a cylindrical surface back onto a work plane.This should be made possible.Workaround: None found. Attempts to use sheet metal functions were unsuccessful.
Trace curve created with MDX analysis need to be updated When we create an analysis and a trace curve, we can’t update the curve trace. The trace curve need to be automatically updated
The acceptable type of elements for the cam cannot be a curved surface. However, this function is very used to simulate an abutment
For curves selection in CAM definition, it is not possible to use an intelligent selection (tangent, from surface,…) It’s necessary to select curves one by one with CTRL.
Have a timescale similar to Pro / animation in which we would find : -time of an analysis -motors -…
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.