Recently active
This may be a repeat request (but I didn't see one when I searched).There may also be another option than what I'm proposing here, so please be kind.This is a request to allow ModelCHECK to flag specific density values (like an itemized list of values) that are bad. Today, the DEF_DEFAULT setting looks for 1.00. That's fine in some cases, but not all. Imported vendor models will often have densities assigned that are not 1.00, a value based on the material, or even a value that's anywhere near a realistic value. This means ModelCHECK skips them.This request would effectively allow us to use an "OR" statement.Here's an example: IF density = 0 OR density = 1000 OR density = 1.2345 THEN issue an error. Something like that.I don't know if this would also require some sort of tolerance/accuracy, or would read the exact value including significant digits. 1.00 vs. .999. I realize that we'd could end up with a pretty long list, but the cap
Below functionality need to be done through toolkit:-- Set Start (under Routing tab of piping application)-- To Pnt / port (under Routing tab of piping application)-- Pipe Solid (under Fabrication tab of piping application)Thanks and RegardsKetan
Hi,Currently, we are not getting any report parameter for pipe segment length i.e. length between two bend in pipe.So our idea is to create repeat region report parameter for segment length.e.g. shown in below snapThanks,Prashant Pandarkar
Modelcheck help indicates that you can combine several start files into a single configuration. The example they gave was PRT_PARAMETER WIDGET STR EQ GREEN in one file and BLUE in another. After speaking with support, this will ONLY work if the "first three items after start tag (Mode) in the start item are same (WIDGET STR EQ)". However, if the two start files include PRT_DATUM PLANE 'name' 'number' and the name changes with the same number then it will not work. Modelcheck should be able to use the last start file and understand that the feature name will be different for the feature number and not flag it as an error - no matter what is listed, since it will be in violation of at least 1 start file.
It would be great if there was a way to accomodate using 2 different size clearance holes, as is necessary when using a shoulder bolt. You need a clearance hole on the top layer for the shoulder, a smaller clearance hole for the second surface (which the shoulder rests on), and then a nut on the bottom surface. To broaden the suggestion: It would be great if in the IFX references dialogue, there was an advanced option that allowed for non generic fasteners like shoulder bolts, anchor nuts, barrel nuts and others that require more than just a surface and axis reference (that aren't uniform around an axis).
Currently it is not possible to allow for drawings to have no format while using ModelCheck FORMAT_NAME option. Please add an option to allow no format as we create DXF drawings without drawing formats and need an ModelCheck option to allow a drawing to not have a format. This would be option the Creo Admins could decide to use or ignore. Another way to "solve" this today would be turning off the format display but this would require a change of a lot of legacy drawings. It would be much simpler to have to option of allowing no formats or not.
Добрый день there is no solution how to let users simply pass through MCH pop-up prompt asking to perform a drawing check. Users always have to type Y/N and confirm some option. It is annoying and wasting of time for most of them. According to our beloved PTC there is no option driving it (except Toolkit) and workaround given in this case is silly bcs calling macro or clicking dialog is almost the same. My suggestion is to add config option like "MCH_run_on_dwg_models" with 3 options: Yes - Always run on all drawing models/sheets (don't ask user = no dialog) No - Always run on current drawing model/sheet only (don't ask user = no dialog) Ask - Ask user (same as now = show dialog)
https://community.ptc.com/t5/Discussions/Material-and-covering-for-the-fasteners/m-p/479151#M141 One of the solution is to add SUBTABLES in dat files like in AFX. Need to possibility to select a material, covering and so on (a value to model parameter) from drop down menu. Without a need to duplicate dat files.
ModelCHECK should be enhanced to have a check to inform the user if a table is missing. Currently there is only a check to see if the values are correct in specific cells (DRW_TABLE_CELLS ), but not if the table exists.
A drawing dimensions that is set to "Tolerance Value Only" should be flagged by ModelCHECK as an overwrite dimension. Currently, we are getting a lot of fake values by engineers who are adding text to dimensions that are set to display the tolerance only.
When modifying the original value of the fillet in a sketch there are 2 different conditions that are causing constraint related failures.1) 1) When there are 2 intersecting lines that are not in the horizontal or vertical position.2) 2) When there is an intersection between entities that are not lines. (Arcs or Splines)With the shown example I have locked the dimensions that I need to keep the sketch stable.With case 1 even though the intersection is dimensionally locked when a fillet is applied it replaces these constraints.Creo even recognizes the error it creates as shown below.When you modify the fillet to the needed size it will invariably move the position as shown below.With case 2 instead of having 2 lines I have replaced one of the lines with an arc. (The same type of results apply with using a spline), once again when I place a fillet it removes the original locked constraints. Once again in the message tree y
The Proj. Ref. Point in Annotation only supports normal Lines. It might be possible to select Arcs.Der Projiz. Bezugspunkt im Annotation sollte auch Bögen unterstützen und nicht nur gerade Linien.
Sehr geehrte Damen und Herren,wenn ich mit Creo 2.0 eine Zeichnung öffne, dann ist immerdie Registerkarte "Layout" aktiv.Nun habe ich mir eine neue Registerkarte erstellt mit meinem Namen.Man sollte die Multifunktionsleiste so umdefinieren können,dass unmittelbar nach dem Öffnen einer Zeichnung die selbst erstellte Registerkarteaktiv ist.Im Moment ist nach dem Öffnen einer Zeichnung nach wie vor die Registerkarte "Layout" aktiv.Dies kann man zur Zeit nicht umsellen.
Below are a few suggestions to help constrain the model better by removing unecessary 0 dimensions:Config option that defaults a constrain type for Mate/Align to coincidentSheetmetal Flat/Flange Feature: be able to constrain the ANGLE by Perpendicular, Parallel...Sheetmetal Flat Feature: be able to constrain the edge offset without going into the sketch to coincident
This way it would be quick & obvious which BrowserView was being shown. This is consistent with other parts of the UI like the main window title bar which can show things like the active viewport or current "application."
When using the external placement functionality of a Merge/Inheritance feature, the placement functionality is not as robust as assembling a component in an assembly. For instance, you can only preview the model in the main geometry window. You can't select surfaces in the main geometry window. You don't get the option to toggle between seeing the component in the small window or the main window. It would be helpful to see and manipulate the placement in the main window.
Repeat component, with new component referance could be very time saving.
Dear Sir or Madam,I would wish for enhancement in this case to keep the name of the feature an extend the name a with an additionel index such as _1. (serially numbered)With kind regardsHans-Jürgen Kapfer
If a part is unreserved, or otherwise locked, Draft Analysis will not run. There are some features in Draft Analysis that modify the part, but for the vast majority of uses, there is no change, just visualization. Don't warn me that Draft Analysis can't be run until I'm actually trying to changes a part. See also more efficient communication with warnings/dialogs
If from Drafting or Annatation I save for the first time a Drawing in Model Manager or I save one that already exist, happens that mi file created has titleblock not proplerly filled with masterdata ed drawing metadata information. So if I export mi file from Model Manager Workspace I obtain a mi file that has titleblock not properly filled. I ask to modify this behavior that seems to be a bug.
Similar to Application.ScreenUpdating = False in VBA. It would help speed up actions for more complex mapkeys.
If you have a flexible component or multiple simplified reps of a component that has a parameter with type NOTE in the repeat region the current functionality does not combine the same component into a single row. I would like the same behavior in the repeat region for flexible component and simplified rep components with note parameter as I get when I use a a string parameter. Reference Case# 11800613
In drawing mode give function to determine reference of a snapline. Can currently change the attachment, also need the ability to know what the reference is.
When doing a nibbling sequence in NC Sheetmetal Manufacturing, to avoid selecting each individual edge and have the Creo auto detect when there isn't material, on the workpiece, to remove.
Flat Pattern Preview is a great enhancement for Creo Parametric, if we can use Boundary Box dimensions of Flat Pattern Preview in relations, it will more perfect.https://support.ptc.com/appserver/cs/view/case_solution.jsp?n=CS106486&lang=en
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.